Background

Microalgae are considered one of the most promising biofuel feedstocks [1, 2]. However, the high cultivation cost is still a limiting factor for its further commercialization [3]. Using wastewater for microalgal cultures is considered mutually beneficial, because the wastewater provides nutrients for microalgal growth, while the microalgae remove pollutants from the wastewater [4, 5].

Digestate is an important byproduct of the anaerobic digestion of organic waste [5, 6]. Traditionally, land application is the primary method for managing digestate from livestock farms [7]. However, with the rapid development of the biogas industry, the volume of digestate has increased substantially in recent years. Land application and other digestate processing techniques require large energy inputs and increase environmental risk, especially with respect to liquid digestate from large scale biogas plants in large livestock or poultry farms [6]. Digestate management has become a major bottleneck in the development of the biogas industry, as well as for the livestock and poultry breeding industry [8]. On the other hand, the liquid digestate is rich in nitrogen (N), phosphorous (P), potassium (K), and other nutrients essential for microalgal growth [9]; thus, its use as a microalgal culture medium is considered a new opportunity for digestate valorization [6, 9].

Culturing microalgae in liquid digestate can reduce the cost of nutrients for microalgal cultivation, while simultaneously reusing liquid digestate [9]; however, there are some limiting and inhibitory factors in liquid digestate-based microalgal cultivation. First, the high turbidity of liquid digestate, caused by suspended materials, can lead to low transmittance. This reduces the efficiency of photosynthesis and the growth of microalgae [10]. Moreover, the ammonium-nitrogen (NH4+-N) levels in liquid digestate are usually high and can potentially inhibit microalgal growth [11]. Pretreatments, such as separation and dilution, are often used to reduce the negative effects associated with high NH4+-N and turbidity; however, these processes consume a large quantity of energy and fresh water [9].

Struvite (magnesium ammonium phosphate; MAP) precipitation can reduce NH4+ and suspended solids (SS) in wastewater under alkaline conditions, while simultaneously generating slow-release fertilizer [12, 13]. This technique has been also used to recover N from digestate [14]. However, the pH of liquid digestate is usually neutral or weak alkaline, and it has less PO43− and Mg2+ compared to NH4+. As such, chemicals containing PO43−, Mg2+, or OH− must be added to facilitate effective NH4+ removal [15, 16]. As a result, the candidate supernatant for microalgal culture following precipitation usually has a high pH and salinity, as well as an unsatisfactory N:P ratio for microalgal growth. The suggested optimal N:P mass ratio for microalgal growth is approximately 7:1, based on the composition of microalgae [17]; however, the N:P molar ratio in liquid digestate is usually adjusted to approximately 1:1 (mass ratio around 0.45) at the beginning of the reaction to achieve a high precipitation efficiency [18, 19]. In fact, the remaining N and P levels, as well as the N:P ratio in the supernatant, are under the control of the reaction conditions, such as pH value and PO43−:Mg2+:NH4+ molar ratios [19]. Thus, one goal of this study was to determine the optimal combination of chemical additives and reaction conditions of struvite precipitation in liquid digestate, to obtain an optimal supernatant for microalgal growth.

Most microalgae prefer neutral environments; as such, the high pH and salinity in the struvite-precipitated supernatant may negatively affect algal growth. However, reducing the pH and salinity in the supernatant is usually not economical. Microalgal species have a range of optimal pH and salinities, with some species tolerating high pH and salt conditions [20]. Selecting high pH and salt tolerant species is beneficial for culturing microalgae in liquid digestate after struvite precipitation. Therefore, in this study, struvite precipitation was selected as a digestate pretreatment technique to determine the optimal combination of chemical additives and reaction conditions, and to investigate suitable microalgal species. This provides a new way for combining liquid digestate treatment and microalgal cultivation [21].

Methods

Liquid digestate collection and characterization

The liquid digestate used in this study was obtained from a pig farm located in Jianyang, Sichuan province in China. The samples were collected from a storage pond after treatment in an anaerobic continuous stirred tank reactor (CSTR) with the raw materials of swine wastewater after separation. They were immediately transported to the laboratory and stored at 4 °C until use.

Microalgal strains and growth medium

Nine microalgal strains were collected from the Freshwater Algae Culture Collection at the Institute of Hydrobiology (FACHB-Collection, Wuhan, China), including Chlorella regularis FACHB-1068, Chlorella pyrenoidosa FACHB-9, Botryococcus braunii FACHB-357, Scenedesmus obliquus FACHB-417, Dictyosphaerium ehrenbergianum FACHB-1223, Haematococcus pluvialis FACHB-712, Spirulina subsalsa FACHB-351, Spirulina platensis FACHB-900, and Spirulina maxima FACHB-438. The three Spirulina strains were cultured in the Spirulina medium [22] and the other strains were cultured in BG-11 medium [23].

Experimental procedures

Struvite precipitation

MgSO4·7H2O, MgCl2·6H2O, and MgO were used as sources of Mg2+; and K2HPO4·3H2O, KH2PO4, and NaH2PO4 were used as sources of PO43−; Fig. 1 and Table 1 show the combinations tested in this study.

Fig. 1
figure 1

Effect of Mg2+ and PO43− sources and stirring time on transmittance (NH4+:Mg2+:PO43− molar ratios at 1:1.2:1.2, pH at 9.0, and constant rate at 150 rpm). Errors bars show standard deviation (n = 3)

Full size image
Table 1 Effect of KH2PO4 and NaH2PO4 on transmittance, NH4+-N removal rate, and salinity
Full size table

To evaluate the effect of the Mg2+ and PO43− sources and stirring time on struvite reaction, 300 ml of liquid digestate were fed into a 500-ml beaker. After this, different combinations of Mg2+ and PO43− sources were added and mixed by continuous stirring with a magnetic stirrer at a constant rate (150 rpm) to make the PO43−:Mg2+:NH4+ molar ratios of each solution at 1:1.2:1.2. When the exogenous compounds were dissolved, the pH of the mixture was adjusted to 9.0 using 0.1-M NaOH [19]. The stirring continued for 0, 1, 2, 5, 10, and 20 min after the pH reached 9.0; stirring then stopped to allow sampling. A 10-ml sample of each mixture was placed into its own 15-ml centrifuge tube. After settling for 30 min, the supernatant from each centrifuge tube was used for analysis.

To select the best precipitation conditions for optimal microalgal growth in terms of residual NH4+-N concentration and N:P mass ratio, further experiments were done at different pH values (8.0, 8.5, and 9.0) and at different P:Mg:N molar ratios (1:1:0.95, 1:1:1, and 1:1.2:1.2) with the ideal Mg2+ and PO43− sources and stirring pattern identified above.

Microalgal cultivation

The struvite-precipitated supernatant obtained above acted as a nutrient source to cultivate nine microalgal strains. Each strain was cultivated in an Erlenmeyer flask (250 ml) as a single batch (100-ml working volume) at a constant temperature (25 °C). A 12-h light/12-h dark cycle was provided using daylight fluorescent tubes with a photon flux density of 40–50 μmol/m2/s. The cultures were manually shaken 2–3 times per day to prevent biomass sedimentation as described previously [24]. The biomass in each Erlenmeyer flask was after 7-day cultivation.

Once a suitable microalgal strain was chosen, laboratory-scale cultivations were conducted in 1.2 l reactors (1 l working volume) for 10-day cultivation. Either struvite-precipitated supernatant or BG-11 was used as the culture medium. An ambient air flow of 0.2 l/min was provided to each reactor in a 12 h/12 h cycle, consistent with the photoperiod described above.

Analytical methods

Water quality analysis

The pH value and salinity of the solution was measured using a pH meter and conductivity meter, respectively. Transmittance was measured using spectrophotometry at 680 nm [25]. Chemical oxygen demand (COD) was determined according to standard methods described by APHA [26]. After filtration through a 0.45 μm membrane, the concentration of NH4+-N and NO3−-N was analyzed using an AA-3 autoanalyzer (Bran + Luebbe, Germany). PO43−-P was measured by the molybdate-ascorbic acid colorimetric method described by APHA [26]. Scanning electron microscopy and X-ray diffraction analysis were used to analyze the struvite precipitate.

The struvite precipitate collected from the bottom of the beakers was dried at room temperature (25 ± 2 °C) and ground using a mortar. The powder (with particles that passed through a 200 mesh) was imaged using scanning electron microscopy (Hitachi SU1510, Japan) with an energy-dispersive spectrometer system (SEM–EDS) (Horiba EX-250, Japan). The crystal structures of struvite precipitation were measured using X-ray powder diffractometer (XRD) (Bruker D8 ADVANCE, Germany). The scattering was operated at a power level of 60 kV and at 80 mA. The data were recorded at a speed of 4°/min over the angular range of 10°–60°.

Microalgal growth and total lipid analysis

The specific growth rate (μ) based on dry cell weight (DCW) was used to evaluate the growth of each microalgal strain in the struvite-precipitated supernatant. To determine DCW, 10-ml microalgae samples were collected and centrifuged at 3200g for 10 min and then washed twice in 0.5 M of ammonium formate (HCOONH4) to remove impurities. The harvested microalgae were dried in an oven at 60 °C until the samples reached a constant weight. The samples were subsequently cooled to room temperature in a desiccator before weighing. The specific growth rate (μ) was calculated as follows:

$$\upmu = ({ \ln }X_{\text{final}} {-}{ \ln }X_{0}) /(t_{\text{final}} {-}t_{0} ).$$
(1)

In this expression, Xfinal and X0 are DCW (mg/l) at the first (t0) and last time point (tfinal), respectively.

Growth curves based on DCW, biomass productivity (BP), and lipid productivity (LP) were used to calculate the growth status of the selected microalgal strain. To draw the growth curve, 10-ml microalgae samples were collected from the 1.2-l reactors every day, and the DCW was measured as described above. At the end of the exponential phase, the BP was calculated using the following equation:

$${\text{BP}}\left( {{\text{mg}}/{\text{l}}/{\text{day}}} \right) = \left( {{\text{DCW}}t_{\text{final}} {-}{\text{DCW}}t_{0} } \right)/\left( {t_{\text{final}} {-}t_{0} } \right).$$
(2)

This calculation applied two time intervals of DCW (mg/l).

The total lipid content was extracted using an extraction method adapted from Bligh [27]. Approximately 0.1 g of dried microalgae powder was transferred into a 10-ml glass tube, and 3-ml 2:1 chloroform–methanol (v/v) mixture was then added. This mixture was blended with a vortex mixer at room temperature for 10 min. Then, 1-ml methanol was added to the mixture and blended for 1 min; 1.8-ml distilled water was then added to the mixture and blended for 5 min. Finally, the mixture was centrifuged at 3200g for 10 min. The organic phase was transferred to another glass tube and washed twice using a 5% NaCl solution. The final organic phase was carefully collected, the solvents were dried at 60 °C in an oven, and the weight of the remaining lipids was recorded. The total lipid content was calculated as a percentage of the total biomass (in % DCW). LP was calculated using Eq. (3):

$${\text{LP}}\left( {{\text{mg lipid}}/{\text{l}}/{\text{day}}} \right) = {\text{BP}} \times {\text{lipid content}} \times 100.$$
(3)

Fatty acid profile analysis

Fatty acid content and composition analysis were determined in two consecutive steps, including the preparation of fatty acid methyl ester (FAME) and the analysis using Gas Chromatography–Mass Spectrometry (GC–MS) (Agilent, USA). FAME was prepared using a one-step extraction–transesterification method, as described by Indarti et al. [28], with a minor modification. Dried microalgal samples (approximately 500 mg) were weighed into clean, 50-ml screw-top glass bottles, to which a 20 ml mixture of methanol, concentrated sulfuric acid, and chloroform (4.25:0.75:5) were added. Transesterification was carried out in a 90 °C water bath for 90 min. Once the reaction was completed, the chloroform layer containing the FAME was carefully collected for GC–MS analysis. The oven temperature was set at 80 °C, held steady for 5 min, was then raised to 290 °C at a rate of 4 °C/min, and was then held at 290 °C for 5 min. The resulting compounds were identified in the NIST Mass Spectral Database and quantified by the area normalization method.

Statistical analysis

Each experiment was performed in triplicate and was repeated at least three times. The experimental results were reported as the mean value of each parameter with standard deviation. Statistical analysis was performed using a one-way analysis of variance (ANOVA) followed by a Tukey pairwise comparison, using Origin 10.0. A p value < 0.05 was considered statistically significant.

Results and discussion

Optimization of struvite precipitation

The concentrations of COD, NH4+-N, NO3−-N, and PO43−-P in the digestate used in this study were 629.05, 591.2, 0.07, and 9.87 mg/l, respectively. The pH value was 8.2; the transmittance was 0.11%; and the salinity was 0.26%.

Additional Mg2+ and PO43− ions were required to achieve high struvite precipitation efficiency in the liquid digestate. The sources of Mg2+ and PO43− significantly affected the quality of the struvite-precipitated supernatant [12]. In this study, six combinations were first tested at a NH4+:Mg2+:PO43− molar ratio of 1:1.2:1.2 and a pH of 9.0, as described by Perera et al. [19]. Figure 1 shows that the combination of KH2PO4 + MgCl2 resulted in the highest transmittance at the first test time point (0 min), reaching 80%; this combination was followed by KH2PO4 + MgSO4, K2HPO4 + MgCl2, and K2HPO4 + MgSO4, which resulted in transmittances of more than 60%. The two MgO combinations exhibited low transmittance due to the low solubility, while the K2HPO4 + MgO combination resulted in the lowest transmittance of approximately 10%. This indicated that KH2PO4 and MgCl2 were the better choices for obtaining supernatant with high transmittance after struvite precipitation.

In addition, the maximum transmittance of each combination occurred when the pH reached 9.0, and it gradually decreased with continued stirring (Fig. 1). The struvite formed flocs and rapid precipitation reduced the suspended solids, thereby improving the transmittance of the liquid digestate. Continuous stirring could destroy the flocs, causing suspended fine particles that could decrease the transmittance. Therefore, in subsequent experiments, the stirring was stopped as soon as the pH reached the predetermined value.

The NH4+-N removal rate and the salinity of the supernatant were measured after 30 min of sedimentation at the first test time point (0 min). The NH4+-N removal rate displayed the same trends as the transmittance (Fig. 2). The combination of KH2PO4 + MgCl2 also resulted in the highest NH4+-N removal rate, at more than 90%. In addition, the KH2PO4 resulted in a lower salinity, while the MgCl2 resulted in a higher salinity than with MgO and MgSO4; however, the two MgO combinations were not considered due to low light transmittance and NH4+ removal. The remaining two KH2PO4 combinations were considered as alternatives. The salinity of KH2PO4 + MgCl2 was 0.63%, which was slightly higher than KH2PO4 + MgSO4.

Fig. 2
figure 2

Effect of Mg2+ and PO43− sources on NH4+-N removal rate and salinity (NH4+:Mg2+:PO43− molar ratios at 1:1.2:1.2, the stirring was stopped as soon as the pH reached to 9.0). Errors bars show standard deviation (n = 3). Different letters indicate a significant difference at p < 0.05

Full size image

In nature, microalgae have a large species diversity, allowing them to adapt to salinity changes. In the open ocean, salinity varies between 3.3 and 3.7% [29], which is significantly higher than the salinity obtained in this study. Moreover, salt stress could increase the lipid content of some microalgal species [30]. Of the six combinations, we selected KH2PO4 + MgCl2 for further investigation. Other studies have confirmed that the dominant form of P in MAP formation reaction is H2PO4− or HPO42− [31]. In this study, the H2PO4− achieved better results with higher transmittance, NH4+-N removal rate, and lower salinity. Yetilmezsoy and Sapci-Zengin [32] found similar results when recovering NH4+-N from the effluent of a UASB treating poultry manure using MAP precipitation.

NaH2PO4 is often used as a PO43− source for struvite precipitation [12]. As such, we further analyzed the differences between NaH2PO4 and KH2PO4. The results indicate that the KH2PO4 + MgCl2 combination achieves higher transmittance, higher NH4+ removal rate, and lower salinity (Table 1). The MgKPO4·6H2O (MKP) is one of the struvite analogs, but it is more likely to form if NH4+ concentrations are low [31, 33]. The liquid digestate used in this study was high in NH4+; the presence of K+ did not interfere with removing NH4+. Otherwise, potassium is an essential macronutrient and is most abundantly absorbed cation playing an important role in algae growth.

The initial NH4+:Mg2+:PO43− molar ratio and pH of the reaction system significantly affected the precipitation results [12], especially with respect to the remaining N and P in the struvite-precipitated supernatant, which determined the NH4+-N levels and N:P mass ratio in the supernatant. High NH4+-N may inhibit microalgal growth, but inhibitory thresholds vary widely within microalgal species [9]. In general, when the NH4+-N concentrations are below 100 mg/l, the growth of most microalgae will not be significantly inhibited [11, 34]. Only at a NH4+:Mg2+:PO43− ratio of 1:1:0.95, and a pH 8.0 and 8.5, did the remaining NH4+-N in the supernatant exceed 100 mg/l (Table 2).

Table 2 Characteristics of struvite-precipitated supernatant under different NH4+:Mg2+:PO43− molar ratio and pH
Full size table

The initial NH4+-N concentration of the liquid digestate used in this study was 591.2 mg/l. As more PO43− and Mg2+ was added, less NH4+-N remained. In addition, at the same NH4+:Mg2+:PO43− molar ratio, the remaining NH4+-N concentration decreased with an increasing pH value. At a NH4+:Mg2+:PO43− ratio of 1:1.2:1.2 and pH of 9.0, the NH4+-N concentration in supernatant was as low as 38.95 mg/l, indicating a NH4+ removal rate of more than 90% (Table 2). This led to the hypothesis that this method could be used to treat liquid digestates containing up to 1000 mg/l of NH4+-N, to meet the 100-mg/l NH4+-N concentration requirements for microalgal growth.

The N:P ratio is another important factor affecting microalgae growth. According to the typical microalgae composition formula (C106H181O45N16P), optimal microalgae growth occurs when the mass ratio of N to P that can be absorbed by microalgae is approximately 7:1 [17]. NH4+-N, NO3−-N, and PO43−-P are the main forms of N and P absorbed by microalgae [35]; as such, the ratio of the sum of NH4+-N and NO3−-N to PO43−-P was used to evaluate the N:P ratio in this study. The N:P mass ratio in the supernatants ranged from 2.70 to 7.04 (Table 2). At a NH4+:Mg2+:PO43− molar ratio of 1:1.2:1.2 and a pH of 8.5, the N:P mass ratio in the supernatant was 7.04, approaching the ideal value. Moreover, at this condition, the supernatant had the second highest transmittance and NH4+ removal rate.

The shape and composition of the precipitates formed at a NH4+:Mg2+:PO43− molar ratio of 1:1.2:1.2 and a pH of 8.5 were further analyzed using SEM–EDS and XRD techniques. The precipitates showed a typical orthorhombic crystal shape and surface characterization (Fig. 3A), similar to results obtained from other pig slurry and described by Cerrillo et al. [18]. The crystal surface linked some ‘amorphous’ materials and contained a trace level of carbon (C). This probably related to the suspended solids generated from the liquid digestate. The XRD patterns also support the findings that the precipitates were made up of a mixture of struvite and amorphous materials. The prominent peaks of the precipitate matched the standard model for struvite very well, but there was an uneven baseline induced by the amorphous material (Fig. 3B). Flocculating suspended solids is one of the reasons that struvite precipitation improves the transmittance.

Fig. 3
figure 3

Scanning electron microscopy with energy dispersive analysis (a) and X-ray diffraction patterns (b) of struvite from liquid digestate (NH4+:Mg2+:PO43− molar ratios at 1:1.2:1.2, the stirring was stopped as soon as the pH reached to 8.5)

Full size image

In summary, to achieve optimal transmittance, NH4+-N levels and N:P mass ratio for microalgal growth, the NH4+:Mg2+:PO43− ratio of the liquid digestate should first be adjusted to 1:1.2:1.2 using KH2PO4 and MgCl2 with continuous stirring. The pH should then be adjusted to 8.5 by adding NaOH. At that point, the stirring should be stopped. The supernatant obtained under this condition was used for the subsequent microalgae culture.

Screening of suitable algal species

Nine microalgal species were cultured in the struvite-precipitated supernatant (Table 3). After 7 days of cultivation, D. ehrenbergianum showed the highest specific growth rate, followed by C. regularis FACHB-1068 and S. obliquus FACHB-417. In contrast, C. pyrenoidosa FACHB-9, B. braunii FACHB-357, H. pluvialis FACHB-712, and S. platensis FACHB-900 showed almost no growth during this period.

Table 3 Specific growth rate (μ) of different microalgae strains cultured in struvite-precipitated supernatant
Full size table

The genus Dictyosphaerium is found in both marine and fresh water environments [36] and some species in this genus have a strong ability to adapt to extreme environments [37]. For example, D. chlorelloides can survive in alkaline and moderately acidified aquatic environments containing hexavalent chromium [38] and Dictyosphaerium sp. has been found in high rate algal ponds (HRAPs) used for wastewater treatment [39]. D. ehrenbergianum was designated as a type species of the genus of Dictyosphaerium [37]. To date, research on this species has mainly focused on its taxonomy [40, 41]; therefore, this study provides a novel application for this alga.

Growth of D. ehrenbergianum in struvite-precipitated supernatant

The growth curve of D. ehrenbergianum based on DCW was monitored in both the struvite-precipitated supernatant and BG-11 (Fig. 4). After a 1-day adaptation period, D. ehrenbergianum showed a higher growth rate in the supernatant than in BG11. By the seventh day, the growth of D. ehrenbergianum cultured in BG-11 stagnated; however, D. ehrenbergianum continued to grow in the supernatant. BG-11 medium, designed to cultivate blue–green algae, is now widely used to grow many microalgal strains, including the genus Dictyosphaerium [23, 38]; however, our results indicate that the struvite-precipitated supernatant was more conducive to D. ehrenbergianum biomass accumulation.

Fig. 4
figure 4

Growth curve of Dictyosphaerium ehrenbergianum in struvite-precipitated supernatant and BG-11. Errors bars show standard deviation (n = 3)

Full size image

Table 4 shows the biomass and lipid productivity of D. ehrenbergianum in both the supernatant and BG-11 after 10 days of cultivation in the same culture conditions. The microalgae exhibited higher biomass productivity (161.06 mg/l/days) in the supernatant than in the BG-11 media. However, the biomass productivity is still lower than reported in other studies [42]. This may be because of the low light intensity of the light incubator (about 40–50 μmol/m2/s) used for this study; similar results were also found in Chlorella sp. [43].

Table 4 Biomass productivity, lipid content, lipid productivity, and fatty acid profiles of Dictyosphaerium ehrenbergianum in struvite-precipitated supernatant and BG-11
Full size table

In this study, the lipid level of D. ehrenbergianum cultured in BG-11 was 23.67%, which is close to the level found for Dictyosphaerium CFR 5-01/FW by Vidyashankar et al. [44]. However, the lipid content of D. ehrenbergianum cultured in the struvite-precipitated supernatant was as high as 34.33%, resulting in lipid productivity of 55.29 mg/l/days. This indicates that the supernatant was also beneficial for D. ehrenbergianum lipid accumulation. Other research has shown that lipid accumulation can be promoted when microalgal cells are cultivated in stressed conditions, such as high salinity [45]. By adding KH2PO4 and MgCl2, the presence of K+, and other ions, increased the salinity (from 0.26 to 0.66%) of the supernatant following struvite precipitation; therefore, the increased salinity in the supernatant did not inhibit microalgae growth, but actually contributed to greater lipid accumulation.

The predominant fatty acids of D. ehrenbergianum cultured in both the struvite-precipitated supernatant and BG-11 were C16 and C18 (Table 4), which are the main components of biodiesels [10]. This indicates that the oil from D. ehrenbergianum is an ideal biodiesel alternative. The microalgae biodiesels usually have poor oxidative stability due to the low monounsaturated fatty acid (MUFA) and saturated fatty acid (SaFA) content [46]. The proportion of total MUFAs and SaFAs of D. ehrenbergianum increased from 32.24% in BG-11 to 45.27% in the supernatant, whereas the proportion of polyunsaturated fatty acid (PUFA) was decreased. This indicated that the lipid profiles of D. ehrenbergianum could change with growth conditions, the supernatant generated through in this study was more favorable for culturing D. ehrenbergianum for ideal biodiesel production. Similar results were also found in the previous study [47].

Conclusions

This study constructed a new way to combine liquid digestate treatment and microalgal cultivation. The study also determined the optimal struvite precipitation conditions for pretreating liquid digestate intended for use as a microalgal culture medium. KH2PO4 and MgCl2 were the optimum source of Mg2+ and PO43− to adjust the NH4+:Mg2+:PO43− molar ratio to 1:1.2:1.2. Continued stirring should be stopped when the pH reaches 8.5. D. ehrenbergianum grew best in the struvite-precipitated supernatant, which enhanced D. ehrenbergianum biomass productivity and lipid content, and also improved the accumulation of MUFAs and SaFAs. The struvite-precipitated liquid digestate can be used to culture D. ehrenbergianum for biodiesel production.