Abstract
The effect of surfactant admixture (stearic and oleic acids) with a variety of milling (dry milling, milling in water and ethanol) on pressing and sintering and magnetic properties of the Fe-30Cr-20Co-2Mo-2W (wt %) hard magnetic powder alloy was studied. The addition of stearic and oleic acids in the amount of up to 2 wt % during dry or wet milling increases the density of pressed samples. The use of surfactants during milling in water and ethanol increases the density of sintered samples. X-ray diffraction shows that only accumulation of defects takes place in the crystal structure of the particles, and no additional phases form during dry or wet milling of powder mixtures containing a surfactant. The best magnetic hysteresis properties were obtained with samples milled in ethanol with 1% stearic acid.
Similar content being viewed by others
References
Kaneko, H., Homma, M., and Nakamura, K., New ductile permanent magnet of Fe-Cr-Co system, Proc. AIP Conf. “Magnetism and Magnetic Materials,” 1971, no. 5, pp. 1088–1092.
Green, M.L., Sherwood, R.C., and Wong, C.C., Powder metallurgy processing of CrCoFe permanent magnet alloys containing 5–25 wt % Co, J. Appl. Phys., 1982, vol. 53, pp. 2398–2400.
Alymov, M.I., Ankudinov, A.B., Zelenskii, V.A., Milyaev, I.M., Yusupov, V.S., and Ustyukhin, A.S., Effect of alloying and sintering regime on magnetic hysteresis properties of Fe-Cr-Co powdered alloy, Fiz. Khim. Obrab. Mater., 2011, no. 3, pp. 34–37.
Milyaev, I.M., Alymov, M.I., Yusupov, V.S., Zelenskii, V.A., Ankudinov, A.B., and Milyaev, A.I., The effect of silicon and molybdenum on magnetic hysteresis qualities of powder 22Kh15KA hard-magnetic alloy, Poroshk. Metall. Funkts. Pokr., 2011, no. 4, pp. 54–57.
Ryaposov, I.V. and Shatsov, A.A., Peculiarities of alloying, structure and properties of powdered hard-magnetic alloy with increased exploitation characteristics, Perspekt. Mater., 2009, no. 1, pp. 57–61.
Shatsov, A.A., Powder materials of the Fe-Cr-Co system, Metal Sci. Heat Treat., 2004, vol. 46, pp. 152–155.
Shatsov, A.A., RF Patent 2334589, 2006.
Shatsov, A.A., RF Patent 2038918, 1991.
Saryanarayana, C., Mechanical alloying and milling, Progress Mater. Sci., 2001, vol. 46, pp. 1–184.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © M.I. Alymov, A.B. Ankudinov, V.A. Zelenskii, I.M. Milyaev, V.S. Yusupov, T.A. Vompe, 2014, published in Perspektivnye Materialy, 2014, No. 4, pp. 51–57.
Rights and permissions
About this article
Cite this article
Alymov, M.I., Ankudinov, A.B., Zelenskii, V.A. et al. The effect of surfactant admixture during milling on pressing, sintering, and magnetic properties of FeCrCoMoW alloy. Inorg. Mater. Appl. Res. 5, 530–535 (2014). https://doi.org/10.1134/S2075113314050037
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S2075113314050037