Russian Metallurgy (Metally)

, Volume 2019, Issue 13, pp 1373–1377 | Cite as

Technologies of Production of Layered Composites

  • A. N. Marycheva
  • T. A. Guzeva
  • P. M. P’e
  • L. Kh. Tun
  • G. V. MalyshevaEmail author


Two technologies of single-part production of layered composites are considered, the main technological operations are normalized, and the properties of the prepared materials are considered. A nonwoven material with a honeycomb structure is used as one of the components of the layered composite material. The properties of the nonwoven material, foam plastic, honeycomb fillers, and spheroplastics are compared. The total time of impregnation of a layered composite material is theoretically and experimentally studied.


layered material composite material vacuum infusion impregnation under pressure 



  1. 1.
    A. P. Petrova and G. V. Malysheva, Glues, Glue Binders, and Glue Prepregs (VIAM, Moscow, 2017).Google Scholar
  2. 2.
    S. L. Bazhenov, A. A. Berlin, A. A. Kul’kov, and V. G. Oshmyan, Polymer Composite Materials (Izd. Dom Intellekt, Dolgoprudnyi, 2010).Google Scholar
  3. 3.
    N. I. Baurova and V. A. Zorin, Application of Polymer Composite Materials for the Production and Repair of Machines: A Tutorial (MADI, Moscow, 2016).Google Scholar
  4. 4.
    I. I. Sokolov, “Cold-curing spheroplastics based on glue binders for aviation engineering,” Klei. Germetiki. Tekhnologii, No. 3, 25–28 (2013).Google Scholar
  5. 5.
    M. G. Dolmatovskii, I. I. Sokolov, and A. V. Stepanov, “Fracture and control of honeycomb structures with spheroplastics,” Konstrukts. Komposit. Mater., No. 2, 97–103 (2009).Google Scholar
  6. 6.
    V. A. Nelyub, M. A. Gorodetskii, L. Kh. Tun, and G. V. Malysheva, “Properties of multilayer polymer composites based on a nonwoven material made of polyethylene terephthalate,” Vestn. Tekhnol. Univ. 20 (24), 74–77 (2017).Google Scholar
  7. 7.
    V. A. Nelyub, “Characteristics of interfacial layers of polymer composite materials,” Polym. Sci., Ser. D 7 (4), 310–312 (2014).Google Scholar
  8. 8.
    N. I. Baurova, “Influence of nanostructured defects in carbon fibers and ribbons on sensor properties,” Polym. Sci., Ser. D 4 (3), 242–245 (2011).Google Scholar
  9. 9.
    G. V. Malysheva, E. S. Akhmetova, and Y. Y. Shimina, “Determination of phase transition temperatures of polymer binding agents by differential scanning calorimetry,” Polym. Sci., Ser. D 8 (1), 17–21 (2015).Google Scholar
  10. 10.
    N. I. Baurova and A. Y. Sergeev, “Structural studies of fracture patterns in adhesive joints after pull out testing,” Polym. Sci., Ser. D 7 (4), 298–302 (2014).Google Scholar
  11. 11.
    N. I. Baurova, “A method of imitational modeling that permits optimizing the properties of polymeric composite materials,” Polym. Sci., Ser. D 6 (3), 265–268 (2013).Google Scholar

Copyright information

© Pleiades Publishing, Ltd. 2019

Authors and Affiliations

  • A. N. Marycheva
    • 1
  • T. A. Guzeva
    • 1
  • P. M. P’e
    • 1
  • L. Kh. Tun
    • 1
  • G. V. Malysheva
    • 1
    Email author
  1. 1.Bauman Moscow State Technical UniversityMoscowRussia

Personalised recommendations