Abstract
The current investigation involves the fabrication and characterization of an aluminium metal matrix composite reinforced with sintered metal preforms. Two types of metallic preforms were used (steel and stainless steel) and a variety of squeeze casting conditions were investigated using systematic design-of-experiments techniques to determine the effect of casting conditions on the composite microstructure and mechanical properties. It was observed that a detrimental reaction phase containing iron, aluminium and silicon formed around the metallic preform particles, with a lower volume fraction of reaction phase forming at the lower melt casting temperature. This reaction phase appears to promote premature fracture by facilitating crack initiation and propagation. The stainless steel-reinforced composites had a smaller volume fraction of reaction phase and exhibited superior properties compared to the steel-reinforced composites.
Similar content being viewed by others
References
F. M. HOSKING, F. FOLGAR PORTILLO, R. WUNDERLIN and R. MEHRABIAN, J. Mater. Sci. 17 (1982) 477.
M. S. HU, J. YANG, H. C. CAO, A. G. EVANS and R. MEHRABIAN, Acta. Metall. Mater. 40 (1992) 2315.
M. J. O'CONNER, F. E. WAWNER and C. C. JONES, J. Mater. Sci. 31 (1996) 164.
T. W. CLYNE, M. G. BADER, G. R. CAPPLEMAN and P. A. HUBERT, ibid. 20 (1985) 85.
D. CRATCHLEY, Powder Metall. 11 (1963) 59.
R. B. BHAGAT, Metall. Trans. 16A (1985) 623.
Idem, AIAA J. 23 (1984) 912.
Idem, Composites 19 (1988) 393.
C. COLIN, Y. MARCHAL, F. BOLAND and F. DELANNAY, J. Phys. IV 3 (1993) 1749.
A. MORTENSEN, L. J. MASUR, J. A. CORNIE and M. C. FLEMINGS, Metall. Trans. 20A (1989) 2535.
L. J. MASUR, A. MORTENSEN, J. A. CORNIE and M. C. FLEMINGS, ibid. 20A (1989) 2549.
A. MORTENSEN and V. MICHAUD, ibid. 21A (1990) 2059.
V. J. MICHAUD and A. MORTENSEN, ibid. 23A (1992) 2263.
P. JARRY, V. J. MICHAUD, A. MORTENSEN, A. DUBUS and R. TIRARD-COLLET, ibid, 23A (1992) 2281.
T. W. CLYNE and J. F. MASON, ibid. 18A (1987) 1519.
R. B. BHAGAT, J. Mater. Sci. 24 (1989) 1496.
C. MITCHELL, in “Metals Handbook, Desk Edition” edited by H. Boyer and T. Gall (ASM International, OH, 1985) p. 420.
J. R. DAVIS, in “Stainless Steels” edited by J. R. Davis and Davis and Associates (ASM International, OH. 1994) p. 21.
R. F. LYNCH, R. P. OLLEY and P. C. J. GALLAGHER, Trans. AFS 83 (1975) 569.
V. R. RYABOV, in “Aluminizing of Steel” edited by V. S. Kothekar (Oxonian Press, New Delhi, 1985).
F. DELANNAY, L. FROYEN and A. DERUYTTERE, in “Cast Reinforced Metal Composites” edited by S. G. Fishman and A. K. Dhingra (ASM International, 1988) p. 83.
F. P. KNUDSEN, J. Am. Ceram. Soc. 42 (1959) 376.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Baron, R.P., Wert, J.A., Gerard, D.A. et al. The processing and characterization of sintered metal-reinforced aluminium matrix composites. Journal of Materials Science 32, 6435–6445 (1997). https://doi.org/10.1023/A:1018686505563
Published:
Issue Date:
DOI: https://doi.org/10.1023/A:1018686505563