Abstract
A new linear integral method for bar hot rolling on roughing train was obtained. First, for plastic deformation energy rate, equivalent strain rate about Kobayashi s three-dimensional velocity field was expressed by two-dimensional strain rate vector; then, the two-dimensional strain rate vector was inverted into inner product and was integrated term by term. During those processes, boundary equation and mean value theorem were introduced; for friction and shear energy dissipation rate, definite integral was applied to the solution process. Sequentially, the total upper bound power was minimized, and the analytical expressions of rolling torque, separating force, and stress state factor were obtained. The calculated results by these expressions were compared with those of experimental values. The results show that the new linear integral method is available for bar rough rolling analysis and the calculated results by this method are a little higher than those of experimental ones. However, the maximum error between them is less than 10%.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Khaikin B E, Kisilenko I A, Tranovskii I Y. Pressure of Metal on Rolls in Section Rolling [J]. Steel USSR, 1971(1): 884.
Arnold R R, Whitton P W. Spread and Roll Force in Rod Rolling [J]. Metal Tech, 1975(2): 143.
Shinokura T, Takai K. Mathematical Models of Roll Force and Torque in Steel Bar Rolling [J]. Tetsu-to-Hagane, 1986, 72(14): 1870 (in Japanese).
Ahmed Said, Lenard J G, Ragab A R, et al. The Temperature, Roll Force and Roll Torque During Hot Bar Rolling [J]. J Mater Process Technol, 1999, 88(1–3): 147.
Oh S I, Kobayashi S. An Approximate Method for a Three-Dimensional Analysis of Rolling [J]. Int J Mech Sci, 1975, 17 (4): 295.
Kazunori K, Tadao M, Toshihiko K. Flat-Rolling of Rigid-Perfectly Plastic Solid Bar by the Energy Method [J]. J Jap Soc Tech Plasticity, 1980, 21(231): 359 (in Japanese).
Pittman J F T, Zienkiewicz O C, Wood R D, et al. Numerical Analysis of Forming Processes [M]. New York: John Wiley and Sons Ltd, 1984.
Kim N, Lee S M, Shin W, et al. Simulation of Square-to-Oval Single Pass Rolling Using a Computationally Effective Finite and Slab Element Method [J]. J Eng Ind, 1992(114): 329.
Park J J, Oh S I. Application of Three Dimensional Finite Element Analysis to Shape Rolling Processes [J]. J Eng Ind, 1990 (112): 36.
Kim N, Kobayashi S, Altan T. Three-Dimensional Simulation of Gap Controlled Plate Rolling by the Finite Element Method [J]. Int J Mach Tolls Manuf, 1990, 30(2): 269.
Montmitonnet P, Chenot J L, Bertrand-Corsini C, et al. A Coupled Themomechanical Approach for Hot Rolling by a 3D Finite Element Method [J]. J Eng Ind, 1992(114): 336.
LI Chang-cheng, REN Yu-hui, ZHANG Li-fen, et al. Measurement and Study on ϕ500 mm Rougher Mill of High Speed Untwist Rod Mill [J]. Iron and Steel, 2002, 37(2): 59 (in Chinese).
ZHAO De-wen, WANG Guo-dong, BAI Guang-run. Theoretical Analysis of the Wire Drawing Through Two Roller Dies in Tandem [J]. Science in China; Series A, 1993, 36 (5): 632.
WANG Guo-dong, ZHAO De-wen. Modern Materiel Forming Mechanics [M]. Shenyang: Northeastern University Press, 2004 (in Chinese).
ZHAO De-wen. Mathematical Solution of Continuum Forming Force [M]. Shenyang: Northeastern University Press, 2003 (in Chinese).
ZHAO De-wen, GUO Chang-wu, LIU Xiang-hua. Surface Integral of Three-Dimensional Velocity Field for Square Bar Drawing Through Conical Die [J]. Trans Nonferrous Met Soc China, 1996, 6(3): 131.
ZHAO De-wen, XIE Ying-jie, LIU Xiang-hua, et al. Three-Dimensional Analysis of Rolling by Twin Shear Stress Yield Criterion [J]. Journal of Iron and Steel Research, International, 2006, 13(6): 21.
ZHAO Zhi-ye. Metal Forming Mechanics [M]. Beijing: Metallurgical Industry Press, 1987 (in Chinese).
ZHAO Ji-hua, GUAN Ke-zhi. Resistance of Metal Plastic Deformation [M]. Beijing: Mechanical Industry Press, 1989 (in Chinese).
Author information
Authors and Affiliations
Corresponding author
Additional information
Foundation Item: Item Sponsored by National Natural Science Foundation of China (50474015)
Rights and permissions
About this article
Cite this article
Deng, W., Zhao, Dw., Qin, Xm. et al. Linear integral analysis of bar rough rolling by strain rate vector. J. Iron Steel Res. Int. 17, 28–33 (2010). https://doi.org/10.1016/S1006-706X(10)60068-4
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S1006-706X(10)60068-4