Abstract
While the quadriceps muscles of human body are quite important to the daily activities of knee joints, the determination of quadriceps forces poses significant challenges since it cannot be measured in vivo. Here, a novel approach is presented to obtain the forces in squat through the combination of motion photography, force transducers measuring, multi-rigid-body theory and finite element analysis. Firstly, the geometrical and angular data of human for squat process were obtained through the analysis of photographed pictures for human squat with camera. At the same time, force transducers were used to measure the reaction forces from feet and to determine the center of gravity for identical squat process. Next, based on the multi-rigid-body dynamics, a mathematical model for human right leg and foot was established in order to determine the quadriceps torques under different squat angles. Then, so as to determine the quadriceps forces along with varied squat angles, a simplified three-dimensional finite element model was built, including tibia, fibula, patella, patella ligament and quadriceps tendon. Finally, the contact pressure of knee joint was analyzed for the squat with the established model of knee joint involving the obtained quadriceps forces from finite element analysis. And it showed that in the 0–90 degree squat process, the peak value of contact pressure of articular cartilages and menisci is increased with the increased squat angle. This study can be referenced for further understanding of the biomechanical behaviors of knee, contact pressure effects of daily activities on knee, and is significantly instructive for sports rehabilitation.
Similar content being viewed by others
References
Anderson, F.C. and Pandy, M.G., Dynamic optimization of human walking. Journal of Biomechanical Engineering, 2001, 123: 381–390.
Anderson, F.C. and Pandy, M.G., Static and dynamic optimization solutions for gait are practically equivalent. Journal of Biomechanics, 2001, 34: 153–161.
Anderson, F.C. and Pandy, M.G., Individual muscle contributions to support in normal walking. Gait Posture, 2003, 17: 159–169.
Komistek, R.D., Mathematical Modeling of the Human Arm: an Aid in the Investigation of the Role of Muscle Forces in the Development of Lateral Epicondylitis. PH.D. Dissertation, University of Memphis, 1992.
Komistek, R.D., Stiehl, J.B., Dennis, D.A., et al., Mathematical model of the lower extremity joint reaction forces using Kane’s method of dynamics. Journal of Biomechanics, 1998, 31(2): 185–189.
Komistek, R.D., Kanec, T.R. and Mahfouz, M., Knee mechanics: a review of past and present techniques to determine in vivo loads. Journal of Biomechanics, 2005, 38: 215–228.
Farahmand, F., Rezaeian, T., Narimani, R., et al., Kinematic and dynamic analysis of the gait cycle of above-knee amputees. Scientia Iranica, 2006, 13(3): 261–271.
Yang, J.Y., Wang, R.Y., Xiong, K.Y., et al., The EMG determination and analysis of quadriceps isokinetic concentric contraction. Journal of Beijing University of Physical Education, 1995, 18(4): 28–34.
Jiang, H.Y., The relationships between integrated EMG activity and mechanics parameters of human quadriceps muscle during voluntary contraction. China Sports Science, 1989, 3: 50–54.
Janet, L.K., Marcus, G.P. and John, C.P., Moment arm of the patellar tendon in the human knee. Journal of biomechanics, 2004, 37: 785–788.
Dimitrios, E.T., Vasilios, B. and Paula, J.R., In vivo changes in the human patellar tendon moment arm length with different modes and intensities of muscle contraction. Journal of biomechanics, 2007, 40: 3325–3332.
Bendjaballah, M.Z., Shirazi-Adl, A. and Zukor, D.J., Biomechanics of the human knee joint in compression: reconstruction, mesh generation and finite element analysis. Knee, 1995, 2: 69–79.
Bendjaballah, M.Z., Shirazi-Adl, A. and Zukor, D.J., Finite element analysis of human knee joint in varus-valgus. Clinical Biomechanics, 1997, 12(3): 139–148.
Bendjaballah, M.Z., Shirazi-Adl, A. and Zukor, D.J., Biomechanical response of the passive human knee joint under anterior-posterior forces. Clinical Biomechanics, 1998, 13: 625–633.
Jalani, A., Shirazi-Adl, A. and Bendjaballah, M.Z., Biomechanics of human tibio-femoral joint in axial rotation. The Knee, 1997, 4: 203–213.
Shelburne, K.B., Pandy, M.G. and Torry, M.R., Comparison of shear forces and ligament loading in the healthy and ACL-deficient knee during gait. Journal of Biomechanics, 2004, 37(3): 313–319.
Périé, D. and Hobatho, M.C., In vivo determination of contact areas and pressure of the femorotibial joint using nonlinear finite element analysis. Clinical Biomechanics, 1998, 13: 394–402.
Li, G., Gil, J., Kanamori, A., et al., A validated three-dimensional computational model of a human joint. ASME Journal of Biomechanical Engineering, 1999, 121: 657–662.
Li, G., Lopez, O. and Rubash, H., Variability of a three-dimensional finite element model constructed using magnetic resonance images of a knee for joint contact stress analysis. ASME Journal of Biomechanical Engineering, 2001, 123: 341–346.
Peña, E., Calvo, B., Martinez, M.A., et al., A three-dimensional finite element analysis of the combined behaviour of ligaments and menisci in the healthy human knee joint. Journal of Biomechanics, 2006, 39: 1686–1701.
Shirazi-Adl, A. and Mesfar, W., Effect of tibial tubercle elevation on biomechanics of the entire knee joint under muscle loads. Clinical Biomechanics, 2007, 22: 344–351.
Guo, Y., Zhang, X.S. and Chen, W.Y., Three-dimensional finite element simulation of the total knee joint in the gait cycle. Acta Mechanica Solida Sinica, 2009, 22(4): 347–351.
Zheng, X.Y., Jia, S.H., Gao, Y.F., et al., Modern Sports Biomechanics. National Defense Industry Press, 2002, 100–163: 366–407.
Ashvin, T., James, C.H.G. and Shamal, D.D., Contact stresses in the knee joint in deep flexion. Medical Engineering & Physics, 2005, 27: 329–335.
Hao, Z.X., Jin, D.W. and Zhang, J.C., Finite element analysis of in vivo tibio-femoral contact features with menisci. Journal of Tsinghua University, 2008, 48(2): 176–179.
Harrington, I.J., A bioengineering analysis of force actions at the knee in normal and pathological gait. Biomedical Engineering, 1976, 11(5): 167–172.
Moeinzadeh, M.H., Engin, A.E. and Akkas, N., Two-dimensional dynamic modeling of human knee joint. Journal of Biomechanics, 1983, 16: 253–264.
Thambyah, A., Pereira, B.P. and Wyss, U., Estimation of bone-on-bone contact forces in the tibiofemoral joint during walking. The Knee, 2005, 12(5): 383–388.
Tumer, S.T. and Engin, A.E., Three-body segment dynamic model of the human knee. ASME, Journal of Biomechanical Engineering, 1993, 115: 350–356.
Taylor, S.J.G., Walker, P.S., Perry, J.S., et al., The forces in the distal femur and the knee during walking and other activities measured by telemetry. Journal of Arthroplasty, 1998, 13: 428–437.
Taylor, S.J.G. and Walker, P.S., Forces and moments telemetered from two distal femoral replacements during various activities. Journal of Biomechanics, 2001, 34(7): 839–848.
Author information
Authors and Affiliations
Corresponding author
Additional information
Project supported by the National Natural Science Foundation of China (Nos. 10702048 and 11102126) and Natural Science Foundation of Shanxi (No. 2010021004-1).
Rights and permissions
About this article
Cite this article
Guo, Y., Zhang, X., An, M. et al. Determination of Quadriceps Forces in Squat and its Application in Contact Pressure Analysis of Knee Joint. Acta Mech. Solida Sin. 25, 53–60 (2012). https://doi.org/10.1016/S0894-9166(12)60006-8
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S0894-9166(12)60006-8