Advertisement

Analysis of effect of gas temperature on cooling stave of blast furnace

  • Ning-qiang Xie
  • Shu-sen Cheng
Article

Abstract

In order to study the effect of gas temperature variation on cooling stave, temperature, stress and displacement distributions of cooling stave were analyzed respectively when gas temperature inside blast furnace increases from 1000 to 1600 °C. The results show that the temperature field on cold side is under control of cooling pipes and hardly changes when gas temperature increases. The temperature gradient and change rate with time near hot sides are greater than those in other regions and the later can reach 100 °C/s. The stress intensity near middle area of hot surface is up to 400 MPa and that’s why there are lots of cracks at this place. The edge of stave is bent to cold side and middle regions between fixed bolts and pin moves to hot side. The displacement around fixed pin is smaller but larger on the edge and the maximum is located on hot side of top surface. The maximum displacement in z direction is about 4 mm and 3 mm in y direction. If the expansion coefficient of packing layer is 1/4, the thickness of packing layer between the cooling staves is 32 mm and 24 mm between sides up and down.

Key words

temperature variation displacement temperature change rate stress intensity packing layer 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    CHENG Shu-sen, XUE Qing-guo, CANG Da-qiang. Heat Transfer Analysis of Blast Furnace Stave [J]. Iron and Steel. 1999, 34(5): 11 (in Chinese).Google Scholar
  2. [2]
    CHENG Shu-sen, YANG Tian-jun, XUE Qing-guo. Analysis of Computational Heat Transfer of the Arrangement for the Cooling Apparatus on Long Campaignship Blast Furnace [J]. J Univ Sci Technol Beijing, 2004, 11(2): 15.Google Scholar
  3. [3]
    CHENG Shu-sen, YANG Tian-jun, YANG Wei-guo. et al. Analysis of Heat Transfer and Temperature Field of Blast Furnace Copper Stave [J]. Iron and Steel, 2001, 36(2): 8 (in Chinese).Google Scholar
  4. [4]
    CHENG Shu-sen. Comprehensive Technology on Long Campaignship of Blast Furnace [D]. Beijing: University of Science and Technology Beijing, 1998 (in Chinese).Google Scholar
  5. [5]
    CHENG Shu-sen, SUN Lei, YANG Tian-jun. Study on Temperature Field of Cooling Plate Lining of Blast Furnace [J]. Iron and Steel, 2004, 39(2): 14 (in Chinese).Google Scholar
  6. [6]
    QIAN Liang, CHENG Shu-sen, ZHAO Hong-bo. Quantificational Indexes for Design and Evaluation of Copper Staves for Blast Furnace [J]. J Univ Sci Technol Beijing. 2008, 15(1): 10.CrossRefGoogle Scholar
  7. [7]
    CHENG Shu-sen, YANG Tian-jun, XUE Qing-guo, et al. Optimum Design and Layout of the Cooling Apparatus for Long Compaignship Blast Furnace [J]. J Univ Sci Technol Beijing, 2003, 10(4): 24.Google Scholar
  8. [8]
    QIAN Liang, CHENG Shu-sen. Realizing the Self-Protect Ability of a Blast Furnace Cooling System With Copper Stave [J]. J Univ Sci Technol Beijing, 2006, 13(11): 1052.Google Scholar
  9. [9]
    QIAN Liang, CHENG Shu-sen, ZHU Qing-tian. Monitoring of Blast Furnace Wall With Copper Stave [J]. Metallurgical Industry Automation, 2006(4): 20 (in Chinese).Google Scholar
  10. [10]
    SHI Lin, CHENG Shu-sen, RUAN Xin-wei, et al. Analysis of Thermal Performance of Blast Furnace Cast Copper Stave [J]. Iron and Steel, 2006, 41(6): 13 (in Chinese).Google Scholar
  11. [11]
    SHI Lin, CHENG Shu-sen. Study of Thermal Distortion Cast Iron Cooling Stave With Surface Alloyed Steel Pipe [J]. Iron and Steel, 2007, 42(11): 9 (in Chinese).MathSciNetGoogle Scholar
  12. [12]
    PAN Hong-wei, CHENG Shu-sen, WU Di-feng. Study on Thermal Test and Computational Simulation of Cast Steel Stave [J]. Ironmaking, 2007, 26(5): 28 (in Chinese).Google Scholar
  13. [13]
    ZHU Qing-tian. A Study on Gas Flow Distribution in Blast Furnace [D]. Beijing: University of Science and Technology Beijing, 2007 (in Chinese).Google Scholar

Copyright information

© China Iron and Steel Research Institute Group 2010

Authors and Affiliations

  1. 1.School of Metallurgical and Ecological EngineeringUniversity of Science and Technology BeijingBeijingChina

Personalised recommendations