Molecular oxygen (O2) is the ultimate “green” oxidant for organic synthesis. There has been recent intensive research within the synthetic community to develop new selective liquid phase aerobic oxidation methodologies as a response to the necessity to reduce the environmental impact of chemical synthesis and manufacture. Green and sustainable chemical processes rely not only on effective chemistry but also on the implementation of reactor technologies that enhance reaction performance and overall safety. Continuous flow reactors have facilitated safer and more efficient utilization of O2, whilst enabling protocols to be scalable. In this article, we discuss recent advancements in the utilization of continuous processing for aerobic oxidations. The translation of aerobic oxidation from batch protocols to continuous flow processes, including process intensification (high T/p), is examined. The use of “synthetic air”, typically consisting of less than 10% O2 in N2, is compared to pure O2 (100% O2) as an oxidant source in terms of process efficiency and safety. Examples of homogeneous catalysis and heterogeneous (packed bed) catalysis are provided. The application of flow photoreactors for the in situ formation of singlet oxygen (1O2) for use in organic reactions, as well as the implementation of membrane technologies, green solvents and recent reactor solutions for handling O2 are covered.
Molecular oxygen (O2) is inexpensive, the most readily available oxidant on Earth, and completely harmless to the environment. O2 is therefore perhaps the greenest reagent available to the organic chemist . Furthermore, O2 is a nontoxic gas and is easy to remove after a reaction. Aerobic oxidation reactions are generally very green because they typically display high atom economy and, in most cases, water is the only stoichiometric byproduct. Until very recently, classical oxidation methods using stoichiometric quantities of toxic inorganic oxidants, such as CrO3, KMnO4 and MnO2, were favored in organic synthesis, even though these protocols generally display poor atom economy and use highly energetic oxidants . More recently adopted oxidation approaches use less toxic oxidants, such as dimethylsulfoxide (DMSO) and hypervalent iodine compounds, but are no less green. As social concern regarding the environmental impact of chemical processes gains more interest, there is an increasing demand to design more sustainable chemical methodologies. Anastas introduced the 12 principles of green chemistry, outlining the steps necessary for more sustainable synthesis practices . Over the last 10–15 years, groundbreaking progress has been made in the development of highly selective aerobic oxidation reactions . The replacement of toxic and corrosive stoichiometric oxidants with processes that use O2 combined with catalytic methodologies will ensure atom efficient and selective synthetic oxidation approaches that are sustainable into the future .
Oxidation chemistry utilizing pure O2 or air as the oxidant source is already used extensively within the bulk and commodity chemical manufacturing sector . For example, 6 basic chemicals are produced using pure O2 and 12 chemicals using air at > 2 Mt/a scale. In the bulk and commodity chemicals sector, the use of air and O2 as the oxidant source is driven by the requirement to keep costs as low as possible. However, O2 is underutilized as an oxidant within the fine and pharmaceutical chemical industry. The bulk chemicals sector deals with low value, high volume products and the corresponding production plants are generally designed and engineered as dedicated continuous processes, whereas fine chemicals and the pharmaceutical sector have historically favored the use of multipurpose batch reactors for the manufacture of high value, low volume products . There are unique process challenges associated with handling gas–liquid transformations within multipurpose batch reactors. Efficient mixing between the liquid phase and gas phase is difficult to achieve; therefore, reactions are often mass transfer limited, which leads to problems when scaling up from laboratory to manufacturing scale. The solubility of O2 in water and organic solvents is poor, thus the reactor needs to be pressurized to maximize the amount of gas in solution to reduce mass transfer effects. Typical commercial scale batch reactors can operate between 2 and 6 bar; therefore, higher pressures require more specialized and expensive equipment. In addition, aerobic oxidation reactions are typically highly exothermic, meaning the heat generated needs to be efficiently removed. These challenges, and the fact that the reaction utilizes potentially flammable O2 under certain conditions, unfortunately increase the perceived scale-up risk, which has rendered the use of O2 virtually unacceptable for pharmaceutical and fine chemical synthesis.
The challenges associated with handling O2 are better addressed by using continuous processing than multipurpose batch reactors [7, 8]. There is a current paradigm shift in the pharmaceutical industry from traditional batch manufacturing to continuous processing for the preparation of active pharmaceutical ingredients (APIs) [9,10,11,12]. This paradigm shift is reflected by a new focus in the pharmaceutical industry on process intensification, sustainability, product quality, safety, energy usage and cost . The United States Food and Drug Administration (FDA) is taking proactive steps to facilitate the implementation of continuous manufacturing within the pharmaceutical industry as an attempt to improve product quality and reduce the environmental impact of pharmaceutical manufacture . The University of Wisconsin-Madison Oxidation Consortium (MadOx) involving Eli Lilly and Co., Merck and Pfizer was established in 2012 as a precompetitive collaboration aimed at solving the challenges associated with aerobic oxidations in pharmaceutical manufacturing . In particular, the consortium focused on the development of safe and scalable continuous flow technologies for aerobic oxidation reactions. Recent reviews have provided overviews of the significant progress made in the last decade towards the utilization of O2 within continuous flow environments [16,17,18].
A significant obstacle to the uptake of aerobic oxidation reactions is that undergraduate organic chemistry textbooks still teach classical oxidation methods, which use toxic inorganic oxidants in stoichiometric quantities rather than more recently developed greener aerobic oxidation strategies. Therefore, organic chemists lack the necessary knowledge to implement these new greener methods. There are hurdles to the implementation of large-scale aerobic oxidations owing to the lack of experience and equipment within pharmaceutical manufacturing. In this article, we highlight selected synthetic examples of liquid phase aerobic oxidation reactions under continuous flow conditions. The first section deals with the process aspects associated with utilizing aerobic oxidation reactions, and also gives an overview of a typical continuous flow setup for performing aerobic oxidations. Subsequently, homogeneous catalysis and heterogeneous catalysis examples are discussed. The utilization of photochemistry for the in situ formation of singlet oxygen (1O2) from ground state triplet oxygen (3O2) is treated only briefly, owing to the large number of examples published. The use of supercritical fluids and liquid carbon dioxide (CO2) as green solvents for aerobic oxidations is examined. Membrane technologies, new reactor developments and scale-up strategies are discussed. The advantages and challenges associated with the utilization of continuous processing for liquid phase aerobic oxidations are highlighted throughout.
Mass and Heat Transfer
The solubility of O2 in organic solvents and water is generally very poor; therefore, the reaction rate for liquid phase aerobic oxidations in many cases is determined by mass transfer from the gas phase to the liquid phase . The solubility of O2 in the liquid phase obeys Henry’s law whereby the amount of dissolved gas is proportional to its partial pressure in the gas phase . Continuous flow reactors have advantages over standard glassware and sealed batch autoclaves in terms of mass transfer, even at a laboratory scale . Within a batch processing environment, much of the gas is in the headspace, thus the reactor needs to be pressurized to maximize the amount of gas in solution. The rate of mass transfer from the gas phase to the liquid phase is also dependent on the interfacial contact area between the gas and liquid phases. The gas–liquid interfacial area to volume ratio decreases considerably with increasing batch reactor size  (see Fig. 1). Consequently, the results achieved within a small scale batch reactor are often irreproducible even within a laboratory batch reactor of slightly different dimensions. The highly exothermic nature of many aerobic oxidations also creates the need for efficient heat removal of the heat generated in the reaction to avoid thermal runaways. The reduction in reactor surface area to volume ratio with increasing reactor size makes it more difficult to remove the heat generated from a reaction at larger scales.
A simplified representation of a gas–liquid flow system for liquid phase aerobic oxidations is shown in Fig. 2. A mass flow controller (MFC) is used to introduce O2 (or diluted O2) in a controlled manner directly from a cylinder. The liquid feed is usually introduced using a pump, either a HPLC, syringe or peristaltic pump. A typical reactor is either a chip-based, tubular coil, packed bed catalyst, photochemical or tube-in-tube system. A back pressure regulator (BPR) is used to control the system pressure. When the O2 gas is not fully dissolved within the liquid phase, different flow regimes can occur within a flow system (Fig. 3), with the exact flow regime depending on the gas and liquid flow rates, channel pattern and dimensions, and the physical properties of the fluid and gas composition. By far the most commonly observed flow regime within microchannels for liquid phase aerobic oxidations is a gas–liquid segmented (Taylor or slug) flow regime. The small vortices, known as toroidal currents, created inside each segment within a segmented flow regime result in enhanced mass transfer . Typical interfacial area to volume ratio value ranges for different reactor types are shown in Table 1 . The small channel dimensions of continuous flow reactors provide a high reactor surface area to volume ratio, enabling the generated heat to be dissipated quickly and allowing precise control of the reaction temperature.
Using Diluted O2
The main challenge associated with the adoption of aerobic oxidation reactions in the pharmaceutical and fine chemical industry is the concern over safety due to the high risk of fires and explosions when flammable organic solvents and O2 are used in combination . The combination of oxygen, organic solvent as a fuel and an ignition source (from a spark, flame, static electricity or heat) results in a potentially flammable mixture, because it satisfies the flammability triangle and thus the conditions for combustion to occur. A common strategy applied in batch manufacturing is to operate below the limiting oxygen concentration (LOC) value by diluting O2 gas with an inert gas, typically consisting of less than 10% O2 in N2 (“synthetic air”), to ensure the system never enters the explosive regime. The LOC value is defined as “the minimum partial pressure of oxygen that supports a combustible mixture”. Stahl and co-workers determined the LOC values experimentally in nine different solvents at elevated temperatures and pressures to ensure that a system could be safely operated without entering the explosive regime (Table 2) . The benefit of operating at such low oxygen concentrations is that it ensures the process is inherently safe because a combustible mixture can never be formed.
Ability to Use Pure O2
Increasing reaction efficiency is fundamental to chemistry. The safe utilization of pure O2 at intensified conditions has been demonstrated on a number of liquid phase aerobic oxidation reactions. The limitation of using a diluted form of O2, for example 10% O2 in N2, is that the O2 is competing with N2 for dissolution in the liquid phase, therefore the reaction is more likely to be mass transfer limited (Fig. 4a) . A substantially enhanced reaction rate can be achieved by using higher concentrations of O2, and even pure O2. The significant improvements in reaction rate achieved by using pure O2 can result in improved product quality and process efficiency. Superior space time yields (i.e., the product yield per unit of time and per reactor volume) can be achieved by using pure O2 compared to using synthetic air because a smaller gas phase is needed for the reactor (Fig. 4b). The utilization of pure O2 may also allow a lower system pressure to be used.
The minimum ignition energy (MIE) is the lowest energy required for an oxygen/organic vapor mixture to spontaneously ignite . The MIE of flammable mixtures are over ten orders of magnitude lower for pure O2 than for air. Most safety studies carried out in microreactors examine the use of O2 for reactions occurring in the gas phase. Veser demonstrated for a Pt-catalyzed H2/O2 reaction to H2O2 that explosion propagation can be completely suppressed at channel sizes below the millimeter range, and thus the process is inherently safe . However, at larger channel dimensions (> 0.4 cm) Poliakoff and co-workers, when investigating the catalytic dehydrogenation of 4-vinylcyclohexane, observed periodic temperature spikes near the surface of the Pd/Al2O3 catalyst bed that indicated the occurrence of cycles of propagating flames . In the case of liquid phase aerobic oxidation reactions, O2 is substoichiometric to solvent, which significantly reduces the likelihood of an explosion. Small oxygen segments alleviate the likelihood that autoignition will occur, because the small channel dimensions do not exceed typical quenching distances for explosion propagation. Furthermore, the solvent plays a role as a heat sink. Unlike batch reactors, tubular flow reactors possess no headspace; therefore there is no headspace containing a large volume of potentially combustible oxygen/organic vapor. Nonetheless, the safety associated with a process should be assessed carefully on a case by case basis. Safe operation can be ensured by employing a properly designed continuous flow reactor that can withstand an explosion event in a worst case scenario . A key benefit of continuous processing is that, generally, a far smaller inventory of the overall material to be processed is present within the system at any one time. Miniaturization reduces the risks and allows for secondary containment of the reactor in the case of an explosion event.
Scale-up and Manufacture
When there is sufficient understanding of a reaction system and adequate process design to address safety concerns and mitigate risks, aerobic oxidations, even using pure O2, can be adopted at large scales through the utilization of appropriate continuous-flow processing systems. Experiments including microcalorimetry, differential scanning calorimetry (DSC) and autoclave explosion pressure measurements should focus on minimizing the perceived scale-up risk through contingency planning for worst case scenarios . There are a number of scale-up strategies that can be applied, including: (1) running the process for a longer time in the same equipment (scale-out); (2) a larger reactor volume with the same channel diameter but faster flow rates; (3) unit parallelization (numbering up); and (4) channel dimension enlarging to provide a larger volume through smart dimensioning . Examples of all of these strategies are shown below.
Oxygen in its ground state, triplet oxygen (3O2), displays relatively low reactivity and poor selectivity; therefore, a catalyst system and/or elevated temperatures and pressures are required to increase reaction rates and improve selectivity. Palladium is perhaps the most studied metal for homogeneous catalyzed aerobic oxidations. A broad range of homogeneous Pd-catalyzed aerobic oxidations reactions have been developed over the last 10–15 years . Palladium catalysts are very sensitive to the oxygen concentration. Pd(II) is reduced to Pd(0) species, which aggregate to form inactive Pd black . This phenomenon causes a significant challenge when attempting to scale-up this chemistry under batch conditions due to poor mixing and temperature control. The direct oxidation of Pd(0) by O2 is kinetically unfavored. With this in mind, the utilization of continuous flow reactors that provide good heat and mass transfer can be beneficial for this type of chemistry by preventing catalyst decomposition through the rapid reoxidation of Pd(0) to Pd(II).
In collaboration with Eli Lilly and Co., Stahl and co-workers reported a continuous-flow setup for the Pd-catalyzed aerobic oxidation of alcohols to their corresponding aldehydes and ketones . The system utilized a homogeneous Pd(OAc)2/pyridine catalyst system and a diluted oxygen gas source (8% O2 in N2). As stated in the Introduction, the main benefit of operating at such low oxygen concentrations is that it ensures that the oxygen/organic vapor will never enter the explosive regime, which makes the process inherently safe. A segmented (Taylor) flow regime provided a large interfacial area between the gas and liquid phases to increase mass transfer. The system was applied for the oxidation of primary and secondary alcohols (ten examples, 76–93% yields) within a 400 mL flow reactor. The oxidation of 1-phenylethanol to acetophenone was demonstrated within a 7 L stainless steel coil flow reactor at a 1 kg scale (Scheme 1). The limitation of Pd catalysts is the low catalytic turnover rate; therefore, in this case, a relatively long residence time (4.5 h) was necessary. Eli Lilly and Co. calculated that it is possible to scale-up from the 7 L reactor vessel by a minimum of two orders of magnitude, while retaining the high pressure rating, low cost, and a length/diameter ratio for the tube of ≥ 20,000/1.
An instructive example for catalyst decomposition in homogeneous Pd systems is a study by Kappe and co-workers (Scheme 2) . Pd black formation was observed in the development of a protocol for a Pd-catalyzed oxidative cleavage of olefins to their corresponding aldehydes and ketones. The system was studied in a relatively simple and cost-effective perfluoroalkoxy (PFA) coil. Improved yields could be obtained by using pure O2 instead of air. Poly(ethylene glycol)-400 (PEG-400) was utilized as a co-solvent in an attempt to stabilize the Pd catalyst under process intensified conditions. PEG has received significant attention as an inexpensive, non-volatile, and an environmentally benign solvent. Visual inspection and inductively coupled plasma mass spectrometry (ICPMS) analysis demonstrated that virtually no Pd black formation occurred when PEG-400 was used as co-solvent. Catalyst loading was lowered successfully to 0.1 mol % without compromising product yield. A variety of alkenes were converted in moderate to good yields using the flow protocol.
The N-methyl group is contained in naturally occurring alkaloids (e.g., morphine, codeine, thebaine or oripavine) and its removal is needed to gain access to potent N-alklyated opioid receptor antagonists. In particular, the Pd-catalyzed aerobic N-demethylation of 14-hydroxymorphinone 3,14-diacetate was achieved using pure O2 in a 100 mL stainless steel flow reactor on a 1 kg scale (Scheme 3) . Prior to scale-up, micro-calorimeter (μRC) experiments and differential scanning calorimetry (DSC) had demonstrated that a safe operation can be ensured. The reaction could be successfully scaled-up by selecting a proper structure geometry for the gas–liquid mixing function . The combination of a FlowPlate A6 and a coiled tube provided good mixing of the gas and liquid phases and sufficient residence time, respectively, for almost quantitative conversion. Subsequent hydrogenation and hydrolysis in flow resulted in noroxymorphone—a precursor to naloxone used to block the effects of opioids in the case of overdose.
The American Chemical Society (ACS) Green Chemistry Institute (GCI) Pharmaceutical Roundtable identified the direct activation of an aryl hydrogen (C–H activation), the conversion of Ar–H into Ar–Ar, as one of the top aspirational reaction classes . One of the benefits of developing selective C–H activation procedures is that it avoids the preparation of aryl halides. An interesting example that highlights the use of process intensified conditions under continuous flow for C–H activation is the aerobic cross-dehydrogenative homocoupling of the unactivated arene o-xylene to 3,4,3′,4′-tetramethyl-biphenyl . The product is important since it is used as a precursor for metal organic frameworks (MOFs). Stahl and co-workers reported a Pd-catalyzed batch approach using 1 bar O2 under unoptimized batch conditions to give the product in a very low yield (7%) after 17 h reaction time . Noël and co-workers successfully developed conditions that were amenable to flow processing. The reaction time could be reduced to 40 min by operating at 100 °C and 40 bar within a stainless steel capillary microreactor to afford the product in 41% yield (Scheme 4a), albeit with higher catalyst and additive loadings.
The same group also reported the connection of two different C–H bonds via a cross-dehydrogenative Heck reaction of indoles and alkenes to prepare vinylindoles . A small library of 3-vinylindole derivatives was prepared in residence times between 10 and 20 min under continuous flow conditions (Scheme 4b).
A benefit of continuous flow reactors is the ability to precisely control the gas stoichiometric ratio when using multiple gas feeds . Kappe and co-workers reported the development of a Pd-catalyzed oxidative carbonylation for the formation of carbonylated heterocycles by using CO and O2 (Scheme 5) . However, the composition of CO in O2 between 15.5 and 93.9 vol% is within the explosive regime. Typically, batch reactions are operated outside of this regime to ensure safety. The flow experiments demonstrated that the stoichiometric ratio of CO to O2 had a critical influence on the yield. A high concentration of CO is important for the carbonylation; however, too much CO was determined to cause faster deactivation of the Pd(II) catalyst by reduction to Pd(0). O2 is also critical to the reaction because it maintains a high level of iodine, which is critical for the reoxidation of Pd(0) to Pd(II), although too much O2 can oxidize the substrate. The optimal CO to O2 ratio was identified as 1:1, which is within the explosive regime but the characteristics of the flow set-up enabled operation within this regime, which would otherwise be inaccessible under batch conditions.
Copper is a non-noble and inexpensive abundant metal, thus its use as a catalyst for aerobic oxidations is desirable . Stahl and co-workers developed a continuous flow process for the aerobic oxidation of alcohols using a Cu(I)/TEMPO catalyst system and 9% O2 in N2 (Scheme 6a) . The reaction rate in this system is usually limited by the aerobic oxidation of Cu(I) to Cu(II). One strategy to increase the O2 concentration in the liquid phase to accelerate the oxidation of Cu(I) is through increasing the system pressure. Thus, relatively short residence times could be achieved by operating at 35 bar pressure and 100 °C to oxidize a variety of alcohols to their corresponding aldehydes. Longer residence times were used for less reactive alcohols. The flow protocol was applied to the oxidation of benzyl alcohol to benzaldehyde, with 100 g of product synthesized over a 24 h operation time.
As stated above in the section Using Diluted O2, a limitation of using O2 diluted with N2 is that the O2 is competing with N2 for dissolution in the liquid phase. Favre-Réguillon and co-workers studied the same Cu(I)/TEMPO alcohol oxidation but used pure O2 as the oxygen source (Scheme 6b) . They argued that by utilizing pure O2 it would be possible to operate the system at a lower pressure and decrease the reaction temperature, because the reaction would be less likely to be mass transfer limited. A substantially enhanced reaction rate and similar yields were achieved by using higher concentrations of O2. The same residence time could be used to obtain similar yields at 5 bar pressure and room temperature. Superior space time yields (i.e., the product yield per unit of time and per reactor volume) were achievable by using pure O2 when compared to using diluted O2.
One of the most active liquid phase oxidation systems is cobalt, manganese and bromide salts in acetic acid as solvent (MC-system). Kappe and co-workers investigated the oxidation of ethylbenzene to acetophenone by using either hydrogen peroxide (H2O2) or air (Scheme 7a) . In contrast to when using H2O2 as oxidant, no catalyst deactivation was observed for oxidations using O2. The selectivity of reaction for either acetophenone or benzoic acid could be controlled through careful manipulation of the residence time and reaction temperature, thus demonstrating the benefit of having precise control over the reaction parameters within a flow environment. A short residence time (6 min) and low reaction temperature (120 °C) resulted in acetophenone as the main product, whereas a long residence time (16 min) and high reaction temperature (150 °C) resulted in the formation of benzoic acid as the main product. The reaction times were significantly shorter than previously published examples for the aerobic oxidation of ethylbenzene (15–50 h).
By using a similar continuous flow configuration, Pieber and Kappe also developed a flow protocol for the Fe-catalyzed aerobic oxidation of 2-benzylpyrdines to their corresponding ketones (Scheme 7b) . Propylene carbonate could be used as solvent instead of using environmentally less desirable DMSO. Propylene carbonate is a nontoxic and biodegradable cyclic carbonate.
Favre-Réguillon and co-workers studied the liquid phase uncatalyzed autoxidation of aldehydes to carboxylic acids within a relatively simple and cost-effective PFA coil reactor operated at room temperature and 5 bar pressure (Scheme 8a) . The group successfully showed that an increase in the two-phase superficial velocity resulted in higher conversions due to the increase of the recirculation velocity within the liquid slugs. At room temperature, and in less than 2 min residence time, without using metal catalysts or radical initiators, conversions up to 50% were observed. By increasing the residence time and, in some instances, by addition of Mn(II) 2-ethylhexanoate (Mn(II)EH) as a catalyst at 100 ppm, conversions could be improved to > 95%. In a later study, the same group conducted a high-throughput optimization for the oxidation of 2-ethylhexanal to 2-ethylhexanoic acid, one of the acids with the highest production capacity worldwide, using a sequential pulse experimentation approach to minimize material consumption . Through this study, the group demonstrated the synergistic use of a large range of salts and Mn(II) catalyst resulted in highly selective aldehyde oxidation. The optimization provided conditions that afforded ethylhexanoic acid in 98% yield within 6 min residence time. In a subsequent final optimization and scale-up study, the oxidation of 2-ethylhexanal in flow was achieved successfully at a throughput of 130 g/h . The same group investigated a Mukaiyama epoxidation of cis-cyclooctene by using a similar flow configuration (Scheme 8b) .
Yu and co-workers developed a continuous flow synthesis for the oxidation of 2,4-dichloro-5-fluoroacetophenone to 2,4-dichloro-5-fluorobenzoic acid with air and pure O2 . 2,4-Dichloro-5-fluorobenzoic acid is a very important API intermediate. Nitric acid functioned as a catalyst and co-solvent (Scheme 9). The reaction proceeded under 2 bar pressure and at 70 °C; thus, only standard PFA tubing was required. The reaction proceeded to give a quantitative yield and the system was stable for 1 kg product to be manufactured. Air could also be utilized as the oxygen source, with only a small drop in yield observed.
A limitation of homogeneous catalysis is that the product needs to be separated from the catalyst after the reaction. The use of a heterogeneous catalyst is one method to prevent the product from becoming contaminated by the catalyst because it is in a different phase, provided that leaching into the liquid phase does not occur. The active metal is dispersed on a support, such as carbon, metal oxide or other inorganic material as a packed bed within a flow system . A number of techniques are used for the preparation of catalysts, including impregnation, adsorption, precipitation or ion exchange . The stabilization of a catalyst on an inert solid support can also improve the thermal stability of catalysts. The improved thermal stability is particularly beneficial given the high temperatures often employed within continuous flow reactors. The incorporation of one or more promoters, derived from the early transition metals, lanthanides and/or main group elements, can further modulate activity and selectivity. However, additional challenges exist for heterogeneous catalyst systems compared to their homogeneous counterparts. Isothermal temperature control can be difficult to obtain and the efficient mixing between the gas, liquid and solid phases can be difficult to achieve . A high steady-state conversion is sometimes not possible to achieve due to catalyst deactivation and/or leaching . An additional difficulty regarding their widespread uptake is that the preparation of heterogeneous catalysts is often outside the skill set of a standard organic chemist.
The aerobic oxidation of alcohols using transition metal catalysts on solid supports has received significant attention . Hii and co-workers incorporated a heterogeneous Ru(OH)x/Al2O3 catalyst within an adapted version of the X-Cube flow reactor for the oxidation of benzylic and allylic alcohols using pure O2 (Scheme 10a) . The system could be considered inherently safe under the conditions used, because, even under the maximum pressure of 25 bar, only −97.3 J heat can be generated from the process based on the amount of O2 present. This amount of heat corresponds to an adiabatic temperature rise, ΔTad = 77 °C, and pressure rise, ΔP = 7.1 bar, from the liberation of CO2, a temperature and pressure rise that the reactor can safely withstand. High yields were obtained; however, the flow system was essentially operated in a semi-batch manner, because the reacting mixture was recirculated continuously through the packed bed reactor to achieve high conversions. The resulting reaction times were between 0.75 h to 7 h for the different substrates. Stahl and co-workers also reported using a heterogeneous Ru(OH)x/Al2O3 catalyst for the aerobic oxidation of alcohols (Scheme 10b) . However, in this case, a diluted oxygen source (8% O2 in N2) was used. The catalyst deactivation kinetics were characterized to provide a basis for identification of process conditions that enabled high single-pass yields for a number of aldehydes. In particular, the oxidation of 2-thiophenemethanol was achieved in > 99% yield, which was successfully maintained over a 72 h operation time. The same flow system was also applied to the dehydrogenation of indoline to indole (Scheme 10c).
Kappe and co-workers reported the selective oxidation of benzyl alcohol to benzaldehyde by using an iron oxide nanoparticle catalyst stabilized in a mesoporous aluminosilicate support (Fe/Al-SBA15) within a continuous flow reactor, which the authors term as “flow-nanocatalysis” (Scheme 11) . A 42% fraction of benzyl alcohol could be oxidized within a single pass but recirculation was necessary to achieve full conversion. ICPMS analysis demonstrated that the catalyst does not leach from the reactor, thus indicating the heterogeneity of the reaction mechanism.
Jensen and co-workers studied the oxidation of 4-isopropylbenzaldehyde to cumic acid, an important API intermediate, using a Pt/Al2O3 packed bed within a silicon–Pyrex microreactor (Scheme 12) . An aqueous slurry of the catalytic material was loaded onto glass beads to prepare Pt/Al2O3 as a tightly packed catalyst bed. Conditions that enabled air to be used instead of oxygen without compromising yield and selectivity were identified successfully. The transformation was estimated to take only a few seconds under continuous flow conditions, compared to several hours under semi-batch conditions. Very recently, Lee and co-workers reported the oxidation of cinnamaldehyde to cinnamic acid using silica supported Pt nanoparticles under base-free continuous flow conditions .
A gold catalyst immobilized within a microreactor was used for the oxidation of alcohols with O2 by Kobayashi and co-workers (Scheme 13) . A polysiloxane-coated capillary column was used. The cyanopropyl groups of the polysiloxane were reduced to primary amines, which were cross-linked to the gold catalyst by passing through a colloidal solution of microencapsulated gold at 170 °C for 5 h. The optimal conditions for the oxidation of alcohols were identified as ~ 60 °C, 5 bar pressure and 90 s residence time. A pipe-flow three-phase system was obtained under these conditions, which provided very good mixing between the gas, liquid and solid phases. Benzylic, aliphatic and allylic alcohols were all converted to their corresponding aldehyde or ketone in good to excellent yields. The system was operated successfully using 1-phenylethanol as substrate for 4 days without loss in activity, and no leaching of gold was observed.
The activity, selectivity and stability of a catalyst can be improved through the development of bimetallic catalysts due to the synergistic effects between the two metals when compared to their monometallic counterparts . Gavriilidis and co-workers reported the oxidation of cinnamyl alcohol to cinnamaldehyde by using a bimetallic catalyst system, Au–Pd/TiO2, as a packed bed within a capillary microreactor system (Scheme 14) . The catalyst was prepared by co-impregnation, perhaps the simplest approach for catalyst bimetallic catalyst preparation, with an Au–Pd weight ratio of 1:19. Initially, the researchers demonstrated that the catalyst was stable over a 30 h time period for the oxidation of benzyl alcohol to benzaldeyde. For the cinnamyl alcohol oxidation, in addition to cinnamaldehyde formation, 3-phenyl-1-propanol and trans-β-methylstyrene were also observed as side products. An improved selectivity for cinnamaldehyde was observed at higher oxygen equivalents, albeit with elevated catalyst decomposition. Elevated reaction temperatures were also responsible for catalyst deactivation. A partial recovery in catalyst activity could be achieved by treatment with hydrogen.
A key challenge to designing sustainable flow processes is the discovery of robust multicomponent catalysts which display high catalyst turnovers. The inclusion of promoters has been associated with mediating the adsorption and dissociation of O2, thus preventing over oxidation of the metal surface. Stahl and co-workers conducted an admixture screening in batch for the discovery of new heterogeneous Pd catalyst and promoter compositions . Over 4000 catalyst compositions were explored for the oxidative methyl esterification of 1-octanol to methyl octanoate (Scheme 15a). The screening of simple binary and ternary admixtures of Pd/charcoal in combination with one or two metal and/or metalloid components was conducted. The optimal results were observed with Bi-, Te- and Pb-based additives. PdBi0.35Te0.23/C as catalyst was utilized within a flow system for the oxidative methyl esterification of benzyl alcohol (Scheme 15b). There was no drop in catalytic activity over 120 h after nearly 60,000 catalytic turnovers. ICP-AES (inductively coupled plasma atomic emission spectroscopy) analysis to determine metal content showed that less than 1 ppm (part-per-million) of the three elements leached from the packed bed, corresponding to a stoichiometry change of PdBi0.35Te0.21 to PdBi0.21Te0.12.
The earliest example of a translation of a batch manufacturing process to flow for an aerobic oxidation within the pharmaceutical sector was described by Bristol–Myers Squibb (BMS). BMS researchers were interested in the oxidation of the imide within buspirone to produce 6-hydroxybuspirone (Scheme 16a). Initially, they reported the aerobic oxidation in batch to produce 6-hydroxybuspirone at a 10 kg scale . The reaction was achieved in ~ 71% yield with a throughput of 7.53 kg day−1. However, the conditions used were sub-optimal, the reaction was conducted using synthetic air (6% O2 in N2) to ensure the headspace was kept below the LOC, and cryogenic conditions (− 78 °C) were used to minimize mass transfer effects and to control the reaction exotherm (ΔH = 685 kJ mol−1, ΔTadiabatic = 68 °C). The poorer mass transfer observed at larger scales caused the reaction time to increase from 8 h within a laboratory setting to 16–24 h at the pilot plant scale. Pure O2 had been demonstrated to significantly increase the reaction rate. Thus, BMS sought to identify conditions under continuous flow that could be used to prepare large quantities . Initial studies were conducted using pure O2 at an elevated temperature of −10 °C within a CPC CYTOS stacked-plate microreactor (Scheme 16b). A higher cooling efficiency was possible from the high reactor surface-to-volume ratio within the microreactor. A > 85% conversion could be achieved in less than 3 min residence time to achieve a throughput of 300 g day−1, which, unfortunately, was insufficient to reach manufacturing demands and was much lower than the batch manufacturing protocol. Subsequently, a trickle bed reactor system was developed, which was operated at −38 °C and < 4 min residence time with a counter current flow of O2 (Scheme 16c) . Four reactors in parallel through a numbering up strategy enabled the production of 15.8 kg day−1, which was sufficient throughput for late stage clinical trials. The improvement in yield and throughput from the batch process was attributed to the higher O2 mass transfer rate and the utilization of pure O2 instead of a diluted O2 blend.
The catalyst-free in situ generation of diimide (HN=NH) as a hydrogenation transfer agent for the reduction of alkenes was achieved through the oxidation of hydrazine monohydrate by using O2 as oxidant. Kappe and co-workers reported a continuous flow protocol (Scheme 17a) . However, it was difficult to drive the reaction to full conversion in the case of poorly reactive alkenes. An important step in the production of artemisinin is the diastereoselective reduction of artemisinic acid to dihydroartemisinic acid. A commercial scale synthesis in batch using synthetic air (5% O2 in N2) under atmospheric pressure was reported on a 1 kg scale by Sanofi-Aventis. The reaction proceeded in 11 h using 3 equivalents of hydrazine monohydrate to afford more than 90% yield and 97% diastereoselectivity, corresponding to a space time yield (STY) of 0.023 mmol L−1 h−1 . Kappe and co-workers devised a multi-injection strategy for the introduction of fresh hydrazine hydrate for the reduction of poorly reactive alkenes. (Scheme 17b) . The synthesis of dihydroartemisinic acid could be achieved in 93% yield, corresponding to a STY of 0.56 mmol L−1 h−1. The flow procedure provided a significant improvement in space–time yield in comparison to the batch synthesis. The reduction of thebaine was also achieved using a multi-injection approach but by using four inlet feeds for hydrazine monohydrate .
Organomagnesium and Organolithium Reagents
He and Jamison investigated the direct oxidation of aryl Grignard reagents to form substituted phenols by using compressed air within a segmented flow reactor (Scheme 18a) . Typically, under batch conditions, the aerobic oxidation of aryl Grignard reagents is poor yielding (10–20%) and a mixture of by-products are formed. The flow protocol was successful for the formation of a range of phenols, with either electron-withdrawing or -donating groups, and tolerant for a range of oxidation sensitive functional groups, including alkenes, amines, and thioethers. The protocol was then extended to a three-step continuous flow process by an upstream in situ generation of the aryl magnesium species starting from 1,2-dibromobenzene, iPrMgCl·LiCl and a nucleophile (Scheme 18b). Benzynes were formed as intermediates from the dibromobenzene and the isopropylmagnesium chloride, and subsequent addition of the nucleophile gave the arylmagnesium species. Aerobic monooxygenation finally afforded the phenols in moderate yields after a combined residence time of 14 min for all the steps.
Cyclopentyl mandelic acid (CMPA), a key intermediate in the synthesis of glycopyrronium bromide (glycopyrrolate), is a synthetically challenging intermediate to prepare. The existing manufacturing routes utilize Grignard reagents to afford CPMA in 28–56% yield. Kappe, Luisi and co-workers devised a flow protocol for the sequential α-lithiation and subsequent hydroxylation of α-phenylcyclopentylacetic acid by aerobic oxidation (Scheme 19) . Hexyllithium was utilized as a cost-effective and industrially safe base. A multistep continuous flow protocol was developed that afforded CPMA in 50% isolated yield under homogeneous and mild conditions (atmospheric pressure and room temperature). However, it was difficult to further improve this process and very challenging to prevent decomposition of the desired product, with excess O2 resulting in the formation of the undesired ketone product. The reaction was very sensitive to changes in the input parameters, including temperature, pressure and residence time, thus demonstrating the importance of having precise control over the reaction parameters.
A membrane acts as a gas permeable contact interface between the liquid phase and gas phase to enable the liquid phase to be saturated with dissolved gas . Membranes have been used to pre-load the liquid phase with O2 before a reaction or to continuously introduce O2 to the liquid phase throughout the duration of a reaction. The nature of the contacting method ensures the process is inherently safe because the liquid phase and gaseous O2 are in different channels, thus flammable organic solvents are never in the presence of gaseous O2. In addition, this method also enables better control over residence time at different gas flow rates compared to flow regimes containing undissolved O2, such as a segmented gas–liquid flow regime, within a single microchannel. Membranes are designed to have a large interfacial area to minimize mass transfer effects.
Ley and co-workers pioneered the tube-in-tube reactor gas-loading concept to enable the safer introduction of gases into the liquid-phase . A semipermeable polymeric membrane is permeable to gases but impermeable to liquids. The nature of the contacting method ensures that the use of pure O2 is inherently safe, because it avoids the direct mixing of gaseous O2 with the liquid phase. Teflon AF-2400 (a fluoropolymer) was selected as an appropriate membrane material due to its high permeability to a wide range of gases while remaining impermeable to (nonfluorinated) liquids, its thermal stability and for its resistance to corrosion. The tube-in-tube reactor was successfully demonstrated by Ley and co-workers on the synthesis of phenylacetaldehydes from functionalized styrenes using an aerobic anti-Markovnikov Wacker oxidation involving pure O2 (Scheme 20a) . The O2 was loaded into the reaction mixture using the tube-in-tube gas-loading tool, and the gas-saturated solution then passed through a tubular reactor at 60 °C for 60 min. A copper-catalyzed Glaser–Hay acetylene homocoupling reaction was also demonstrated by the same group (Scheme 20b) . The reaction mixture was loaded with the tube-in-tube gas-loading tool, and the gas-saturated solution then passed through a tubular reactor at 100 °C. The copper and the amine base were then removed from the flow stream by passing it through a cartridge of polymer-supported thiourea and polymer-supported sulfonic acid. The 1,3-butadiynes were isolated in up to quantitative yields, generally without the need for chromatography. Polyzos and co-workers translated the nitro-Mannich α-C(sp3)–H functionalization of N-aryl tetrahydroisoquinolines mediated by iron salts to flow by using the tube-in-tube reactor for the introduction of O2 (Scheme 20c) . Kirschning and co-workers used a Teflon AF-2400 tube-in-tube reactor to pre-saturate the liquid feed with O2 before the feed entered a packed-bed reactor containing immobilized gold-doped nanoparticles (Scheme 20d) . Au-NPs were immobilized on a nanostructured Fe3O4-containing core and a silica shell that was heated in an external oscillating electromagnetic field to catalyze benzylic and allylic alcohol oxidation in the presence of pure O2 or air.
Park and co-workers reported the study of the synthesis of meta-substituted phenols via an oxidative Heck/dehydrogenation sequence within two complementary microreactors, a segmented flow capillary system and a tube-in-tube microreactor . The capillary segmented flow reactor had an internal volume of 0.098 mL, which enabled a microgram optimization study without wasteful reagent consumption (Scheme 21a). The reaction took 130 min within a segmented flow regime compared to 36 h in a traditional batch system. The conditions were then successfully translated to gram scale by using a larger volume tube-in-tube microreactor (7.72 mL) (Scheme 21b). The yields for the reaction of 4-methoxyphenylboronic acid and cyclohex-2-enone conducted within a segmented flow regime and tube-in-tube reactor were comparable, 85% and 84%, respectively.
The performance of reactions can be improved by the continuous supply of O2 through the membrane during the reaction, thus replenishing O2 as it is consumed, rather than pre-saturating the liquid feed prior to the reaction. Continuous penentration of gas ensures that the liquid phase is saturated with O2 throughout the reaction. Enzyme-mediated oxidation chemistry is an emerging topic in organic synthesis . Woodley and co-workers utilized a tube-in-tube flow reactor for the collection of time-series experimental data for the biocatalytic oxidation of glucose to glucose-δ-lactone by glucose oxidase (Scheme 22) . The system displayed a low-dispersed flow regime at the scale investigated resulting in a high degree of accuracy for the kinetic data with minimal material consumption. Buehler and co-workers investigated the hydroxylation of 3-phenylcatechol catalyzed by 2-hydroxybiphenyl 3-monooxygenase (Scheme 22) . The tube-in-tube reactor performs well for research scale experimentation; however, the technology can suffer from limited scalability in terms of performance at scale-up due to mass transfer limitations .
A further benefit of the tube-in-tube approach is that catalyst immobilization is possible within the tube containing the liquid phase. Gavriilidis and co-workers packed a porous inner tube of a Teflon-2400 tube-in-tube reactor directly with the bimetallic catalyst Au–Pd/TiO2 (discussed earlier). The flow system was applied to the oxidation of benzyl alcohol to benzaldehyde (Scheme 23) . Again, the benefit here is that the O2 is introduced along the whole of the packed bed, thus preventing the system from becoming starved of oxygen towards the end of the reactor. Subsequently, the same group developed a packed-bed porous ceramic membrane reactor . However, results indicated that the rate of O2 supply may not be sufficient for fast reactions not to be mass transfer limited .
Stahl and co-workers reported a tube-in-shell reactor (also referred to as tube-in-flask reactor) as an alternative membrane strategy for the safe introduction of O2 into the liquid phase (Scheme 24) . Gaseous O2 is introduced from a cylinder into a stainless steel shell and the O2 permeable tubing carrying the liquid phase is coiled within the shell. A limitation of the Teflon AF-2400 membrane used in the tube-in-tube applications is its relatively high cost (US $25,000/kg). The group identified a polytetrafluoroethylene (PTFE) membrane as an inexpensive alternative (US $2–10/kg) to Teflon AF-2400, which was also compatible with elevated temperatures and pressures. The system was initially demonstrated using the homogeneous Cu(I)/TEMPO catalyst system for alcohol oxidation, with good yields achieved within 1 min residence time. In this case, however, pure O2 was utilized due to the inherent safety associated with the introduction of O2 by using a membrane system. Scale-up was proposed by numbering-up the membrane reactor by assembling a configuration with multiple tubes operating in parallel. The permeable tubing was also packed with Ru(OH)x/Al2O3 and trialled for the aerobic oxidation of benzyl alcohol to afford quantitative yield within 55 min residence time.
Dual- and Triple- Channel Microreactor
Park and Kim developed a dual-channel microreactor with a thin poly(dimethylsiloxane) (PDMS) membrane sheet sandwiched between the two channels (Scheme 25a) . O2 flowing in one channel can pass through the membrane into the second channel containing the liquid phase. The reactor system was applied to a Pd-catalyzed oxidative Heck reaction. The system was shown to give significant improvements over a batch reactor and a segmented microreactor; in particular, less Pd black formation was observed thus demonstrating improved phase contact. The cross coupling products were synthesized in good yields (72–82%) in a short 30 min residence time, compared to 12 h in batch. The dual channel microreactor was also modified and applied to a photosensitized oxygenation of (−)-citronellol . The limitation of the dual-channel microreactor is that only one face of the reaction channel is exposed to gas. The group subsequently developed a triple channel microreactor where the O2 was introduced from either side of the liquid phase to give improved performance (Scheme 25b) .
Photochemistry and Singlet Oxygen
Singlet oxygen (1O2) is an attractive reagent due to its low cost and negligible environmental impact. The formation of 1O2 is usually achieved through the excitation of triplet oxygen (3O2) by using a photoinitator and light irradiation . 1O2 is a highly reactive, unstable and explosive species, which is used as a reagent in a plethora of reactions, including heteroatom oxidations, ene reactions, and cycloaddition reactions . These transformations are often thermally forbidden, but can proceed photochemically. Flow photooxygenations are treated here only briefly owing to the breadth of examples reported; comprehensive reviews can be found elsewhere [94,95,96]. Some examples are given in the sections below. Seeberger and co-workers developed a photochemical flow process for the preparation of 1O2 from 3O2 . Subsequently, the same group applied this technology to the multistep synthesis of the anti-malarial drug artemisinin in continuous flow (Scheme 26a) . The key step towards artemisinin from more readily available artemisinic acid is the formation of allylic hydroperoxide. In this step, the in situ formation of 1O2 is achieved by irradiation with blue LED light (λ = 420 nm), inducing an ene reaction on dihydroartemisinic acid to form a hydroperoxide as an intermediate. The accumulation of peroxide intermediates is avoided because only a small inventory of material is processed at any one time, and the intermediates are telescoped into the subsequent reaction straightaway. The addition of trifluoroacetic acid results in a Hock cleavage of the hydroperoxide. Triplet oxygen then reacts to give artemisinin. Large scale reactions utilizing 1O2 normally require non-flammable halogenated solvents to ensure safe operation, but the process could be modified in flow to use toluene owing to the low amount of oxygen present within the flow system at any one time .
Photochemical reactions pose an additional challenge for scale-up, because the light penetration depth has a critical influence on the performance of photooxygenations . Noël and co-workers presented an interesting numbering-up approach to facilitate the scale-up of a photochemical aerobic oxidation of thiols to disulfides by placing eight capillaries in parallel that are irradiated with white LEDs (Scheme 26b) . A further challenge in parallelization of gas liquid reactions is that efficient and uniform gas liquid distribution can be difficult to achieve within parallelized reactor configurations. The lack of uniform mixing in flow can cause stoichiometry imbalance and poor control of residence in the channels. In the study by Noël and co-workers, the calculated standard deviation for yield was less than 10% across the different channels.
Noël and co-workers reported a mild and selective direct oxidation of activated and unactivated C(sp3)–H bonds enabled by decatungstate photocatalysis (Scheme 26c) . Hydrogen atom transfer (HAT) can be utilized for the production of highly reactive radical species, which can be trapped to give synthetically useful products. Decatungstate is a versatile and inexpensive HAT catalyst that readily performs hydrogen abstraction on C(sp3)–H upon photochemical activation. Initial optimization studies using tetrabutylammonium decatungstate (TBADT) demonstrated that full conversion could not be achieved in batch probably caused by the slow diffusion of oxygen into the liquid reaction mixture and the limited light penetration. Nonetheless, significantly improved results were observed within a continuous flow environment. In particular, the flow approach was successful for the oxidation of natural scaffolds such as (−)-ambroxide, pregnenolone acetate, (+)-sclareolide and artemisinin.
A re-emerging area is electroorganic synthesis [103, 104]. The limitations of conventional batch electrosynthesis can be overcome by using electrochemical flow cells [105,106,107]. Flow electrochemical reactors can be designed to have short distances between electrodes, so no, or only low, concentrations of added supporting electrolyte are required, and a large ratio of electrode area to reactor volume exists. Mo and Jensen reported N-hydroxyphthalimide (NHPI)-mediated electrochemical aerobic oxidation of benzylic C–H bonds to form the corresponding ketones (Scheme 27) . A tube-in-tube reactor was used for the safe introduction of O2 as a co-oxidant into the system. The cation-exchange membrane prevented the reductive decomposition of NHPI at the cathode, because it minimized the crossover of the NHPI anion from anolyte to catholyte. Relatively inexpensive RVC electrodes could be used instead of a platinum electrode. The system described is not inherently a continuous flow process, because the liquid feeds were recirculated to obtain high conversions to accommodate the slow reaction kinetics. In a recent perspective article, Maes and co-workers proposed that many of the challenges associated with selective aerobic oxidation on unactivated C–H bonds could be addressed effectively and safely by making use of flow electrochemistry .
There has been a recent drive within the pharmaceutical and fine chemicals industry towards the utilization of more environmentally benign solvents . GlaxoSmithKline, among others, have published green solvent guides to support the implementation of greener solvents at the discovery and manufacturing stages in API development [111,112,113,114]. As discussed in the Introduction, the main safety challenge associated with liquid phase aerobic oxidations is the utilization of O2 in the presence of flammable organic solvent. A benefit of using continuous flow reactors is the ability to safely operate above the boiling point of a solvent through the pressurization of the system. This feature enables access to elevated reaction rates that would be less accessible, or even forbidden, within batch reactors. The solubility of O2 decreases with an increase in temperature; therefore, the ability to pressurize the system is very important. Another limitation is that the mass transfer of O2 from the gas to the liquid phase is often the rate-limiting step in these processes. Significant efforts have focused on identifying solvents that, under certain conditions, can dissolve all the reaction components (substrate, catalyst and O2) within a single phase. One such solution is to operate within the supercritical regime for a solvent to generate a single phase. CO2 and H2O are both nonflammable and have both been employed in this manner. The application of continuous flow technologies facilitates the effective and safe use of these green supercritical solvents at elevated temperatures and pressures, which would otherwise require more cumbersome, expensive and specialized batch reactors. Another way to reduce the impact of chemical manufacture is to utilize no solvent whatsoever, and to conduct reactions with neat reagents. However neat systems can add complications in terms of thermal management, impurity formation and on the physical properties of the reagents for a particular reaction. Ionic liquids and fluorous solvents are also potentially green solvents for conducting aerobic oxidations [115, 116]; however, as of yet there are no reported aerobic oxidation examples that use these solvents within continuous-flow reactors.
CO2 has attracted significant interest as a green solvent for organic synthesis and chemical manufacture . In fact, CO2 has been proposed as an ideal solvent for pure O2 chemistry . CO2 is produced on a very large scale as a chemical waste product and thus is available in large quantities. There are certain features of CO2 that make it desirable for use as a solvent, and specifically for reactions utilizing O2 . CO2 is inert because it is already oxidized and therefore cannot react further with O2. CO2 has a relatively low critical point (Tc = 31.1 °C, Pc = 72.9 bar). ScCO2 has interesting physical properties such as zero surface tension and high diffusivity. O2 is completely miscible with scCO2 thus the reaction will not be driven by mass transfer from the gas to the liquid phase. Using CO2 as a solvent is advantageous over conventional solvents as it is miscible with oxygen; therefore, only a small excess, or sometimes even stoichiometric amounts, of oxygen are needed in these reactions. However, product extraction after the reaction can be challenging. Leitner, Greiner and co-workers described a continuous-flow system capable of pilot scale production, although not specifically for a reaction utilizing O2 . Leitner and co-workers demonstrated a proof-of-concept Pd-catalyzed aerobic oxidation of primary alcohols to their corresponding aldehydes using scCO2 as reaction medium in flow (Scheme 28a) . To circumvent catalyst deactivation, a giant Pd cluster [Pd561-phen60(OAc)180] was stabilized by a poly(ethylene glycol) (PEG)-1000 matrix to circumvent Pd deactivation, and immobilized within a flow reactor. It is important to ensure good mixing between O2 and CO2 to form a homogeneous mixture before the introduction of the substrate. The catalyst demonstrated reasonable activity and selectivity under unoptimized flow conditions after a single pass.
Poliakoff and co-workers reported the optimization of the oxidation of 2-octanol over a packed bed reactor (5% Pt + 1% Bi on Al2O3) using scCO2 (Scheme 28b) . The system afforded 2-octanone in a consistent 75% yield for 5 h with no evidence for catalyst deactivation and no formation of the octene shown. Subsequently, the system was applied for the oxidation of a number of secondary alcohols (11 examples, 10–75% yield).
Larger scale processes utilizing 1O2 normally require non-flammable halogenated solvents to ensure safe operation. ScCO2 is a greener alternative to these halogenated solvents. ScCO2 has an additional benefit that it lengthens the lifetime of 1O2 (5.1 ms). An early example by George, Poliakoff and co-workers was the photooxygenation of α-terpinene and of citronellol using immobilized photosensitisers . More recently the same group have examined using liquid CO2 (liqCO2) for conducting aerobic oxidations . The vapor pressure of liqCO2 can be much lower than for scCO2, which can enable a reduced pressure limit for the reactor. The production of artemisinin was achieved using liquid CO2 as solvent with EtOAc or PhMe as co-solvent over an immobilized dual function solid acid/photocatalyst (Scheme 29a). It can be difficult to achieve a rapid enough reaction rate at the conditions for liquid CO2, which may limit its widespread applicability. Very recently, the same group also reported the photooxygenation of a range of fulvenes to 3-substituted oxepinones in liqCO2 (Scheme 29b). However, in this case they used a CO2-soluble porphyrin photosensitizer [5,10,15,20-tetrakis-(pentafluorophenyl)porphyrin, TPFPP] . The reactive intermediate was generated within a sapphire tube reactor irradiated with LEDs strips, and the intermediate then decomposed under thermal irradiation to yield the 3-substituted oxepinones. The ratio of the different products formed could be controlled by varying the reaction temperature in the two different reactors, co-solvent selection, substrate concentration and CO2 flow rate.
Water is a green and non-flammable solvent, thus, on these terms, water is the ideal solvent for aerobic oxidations. However, a significant limitation associated with using water within flow reactors is that the inherent carbon richness of organic substrates mean that most do not dissolve in water, causing slow reaction rates. Uozumi and co-workers studied the aerobic oxidation of alcohols in H2O within a catalyzed by platinum nanoparticles dispersed in an amphiphilic polymer within a continuous flow reactor, but very low substrate concentrations were used (10–100 µM) . The likelihood of multiple phases complicates the development of a flow process due to the multiple phases present. One approach to avoid multiple phases is through the dissolution of organic compounds and O2 within a single phase by operating in the supercritical regime for water.
As a proof of concept study, Poliakoff and co-workers demonstrated the aerobic oxidation of methylaromatic compounds to their corresponding carboxylic acid derivatives by using manganese(II) bromide as catalyst and scH2O as the reaction medium . H2O has a high critical point (Tc = 374 °C, Pc = 221 bar). Even at high temperatures, below the supercritical regime H2O still displays some interesting properties. In a more recent example, the same group studied the selective aerobic oxidation of para-xylene to terephthalic acid at both subcritical and supercritical conditions (Scheme 30) . O2 was generated from the high temperature decomposition of H2O2 in a pre-mixer. Subsequently, the same group reported the identification of improved catalyst systems for the reaction . Nonetheless, the high critical point of H2O makes the use of scH2O less synthetically relevant for pharmaceutical applications.
Novel Reactor Developments
The recent developments in reactor technologies for handling O2 have aimed to address the challenge associated with the poor solubility of O2 in water and organic solvents. Thus, efforts have focused on reducing residence times through the enhancement in the mass transfer from the gas to the liquid phase without the need to employ high pressures, which are often undesired. Recent reactor designs have focused on maximizing the interfacial area between the gas and liquid phase to enhance mass transfer.
The laboratories at the University of Bergen and at Fluens Synthesis developed a novel reactor platform called the multi-jet oscillating disk (MJOD) reactor . An electric motor powers the up–down movement of a piston by a variable-frequency and variable-amplitude oscillator (Scheme 31a). The reaction mixture moves from one cavity to the next, and is pushed up the reactor through the jets of the MJOD disks. The reactor was applied to the organocatalyzed Minisci aerobic epoxidation of olefins by N-hydroxyphthalimide (NHPI) . The batch process for this reaction suffers from the limitation of long reaction times (24–48 h), which limits the efficiency and throughput of the process. The changes in the flow created by the oscillating disks resulted in very good mixing, which accelerated reaction rates and enabled residence times of 1–4 h.
A nebulizer-based continuous-flow reactor has been developed for the photochemical 1O2 chemistry (NebPhotOX) by Vassilikogiannakis and co-workers at the University of Crete . A solution containing the substrate and the photosensitizer is nebulized by using pure O2 or air into a chamber that is enclosed by LED light strips to form 1O2 as the reactive intermediate. The NebPhotOx system was used for the photooxidation of β-citronellol (Scheme 31b). The pneumatic nebulizer generates aerosols consisting of fine droplets with an approximate 60 μm average diameter corresponding to a droplet-specific surface areas of 100,000 m2 m−3. The same group also reported the synthesis of cyclopent-2-enones from furans using the NebPhotOx reactor in a similar manner .
Raston and co-workers have developed a vortex fluidic device (VFD) for accelerating and increasing the efficiencies of organic reactions . The dynamic thin film is generated by continuously adding a fluid from jet feeds to a rapidly rotating surface (Scheme 31c). The reaction mixture is rotated at very high speeds (up to 9000 rpm) to produce the liquid phase as a thin film, thus providing a large surface area between the liquid and gas phases. The reactor system was demonstrated on the aerobic oxidation of thiols to disulfides . In particular, the aerobic oxidation of N-acetyl-l-cysteine in water was investigated. Full conversion was achieved in less than 2.5 min residence time within a VFD. The aerobic oxidation within a VFD configuration performed significantly better compared to in batch where only 5% conversion was observed after 1 h reaction time. However, the system was not compared to a segmented flow reactor setup.
George, Poliakoff and co-workers at the University of Nottingham recently reported the construction of a thermal and photochemical “vortex reactor” that uses a rapidly rotating cylinder to generate Taylor vortices (Scheme 31d) . The vortices result in a high interfacial area between the gas and liquid phases, thus enabling rapid dissolution of oxygen into the liquid phase. An interesting feature of the reactor system is that it draws air in from the laboratory so does not specifically need pressurized oxygen from a cylinder, with the optimal uptake of air observed at 4000 rpm. The reactor was demonstrated for a number of reaction systems that utilize 1O2 as a reagent, including the photooxygenations of α-terpinene and furfuryl alcohol and the photodeborylation of phenyl boronic acid. The system was also applied successfully to develop a single process for a three-step synthesis of artemisinin from artemisinic acid.
The falling film microreactor was developed by the Institut für Mikrotechnik (IMM, Mainz). The liquid phase flows through microchannels under gravity to form a thin liquid layer, which is as thin as 20 µm in some instances. The gas input then flows co- or counter-currently to the liquid phase with specific phase interfaces of up to 20,000 m2m−3 generated. Oelgemöller and co-workers studied the photooxygenation of 1,5-dihydroxynaphthalene within a falling film reactor. A 31% yield could be achieved in 160 s residence time (Scheme 32a) . Similarly, Jähnisch and Dingerdissen reported the implementation of a falling film microreactor for the photooxygenation of cyclopentadiene (Scheme 32b) . There was a very small inventory of the endoperoxide produced at any one time, thus improving the inherent safety.
Liquid phase aerobic oxidation reactions offer a valuable alternative to classical oxidation methods using stoichiometric quantities of toxic inorganic oxidants. The challenges (efficient mixing, safety, catalyst decomposition) associated with the use of O2 for organic synthesis can be better addressed through the implementation of continuous flow technology, which can improve reaction reproducibility and provide robust scale-up options. The selection of examples summarized in this review is clear evidence that many aerobic oxidation transformations can be performed effectively and safely under continuous flow conditions. Even pure O2, as opposed to synthetic air, can be safely harnessed in particular instances to provide highly convincing synthetic and manufacturing benefits. Nevertheless, the utilization of continuous flow reactors still poses significant challenges in terms of cost and lack of available infrastructure and expertise available within the synthetic chemistry community. We are convinced that, for environmental, economic, regulatory and synthetic reasons, continuous flow aerobic oxidations will be embraced by scientists and engineers within academic laboratories, and the pharmaceutical and fine chemical manufacturing industries, where further exciting developments can be anticipated in the coming years.
- CrO3 :
Fluorinated ethylene propylene
- H2 :
- HNO3 :
- H2O2 :
High performance liquid chromatography
- K2CO3 :
- KMnO4 :
Light emitting diode
- MnO2 :
Megatonne per annum
- N2 :
- O2 :
- 1O2 :
Singlet state oxygen
- 3O2 :
Triplet state oxygen
- P :
- T :
Jones AB, Wang J, Hamme AT, Han W (2013) Oxygen. In: Encyclopedia of reagents for organic synthesis. https://doi.org/10.1002/047084289x.ro028.pub3
Caron S, Dugger RW, Ruggeri SG, Ragan JA, Ripin DHB (2006) Large-scale oxidations in the pharmaceutical industry. Chem Rev 106:2943–2989
Anastas PT, Kirchhoff MM (2002) Origins, current status, and future challenges of green chemistry. Acc Chem Res 35:686–694
Stahl SS, Alsters PL (2016) Liquid phase aerobic oxidation catalysis: industrial applications and academic perspectives. Wiley, New York
Roduner E, Kaim W, Sarkar B, Urlacher VB, Pleiss J, Glaser R, Einicke WD, Sprenger GA, Beifus U, Klemm E, Liebner C, Hieronymus H, Hsu SF, Plietker B, Laschat S (2013) Selective catalytic oxidation of C–H bonds with molecular oxygen. ChemCatChem 5:82–112
Cavani F, Henrique J (2009) Sustainability in catalytic oxidation: an alternative approach or a structural evolution? ChemSusChem 2:508–534
Stitt EH (2002) Alternative multiphase reactors for fine chemicals A world beyond stirred tanks? Chem Eng J 90:47–60
Cao Q, Dornan LM, Rogan L, Hughes NL, Muldoon MJ (2014) Aerobic oxidation catalysis with stable radicals. Chem Commun 50:4524–4543
Gutmann B, Cantillo D, Kappe CO (2015) Continuous-flow technology—a tool for the safe manufacturing of active pharmaceutical ingredients. Angew Chem Int Ed 54:6688–6728
Movsisyan M, Delbeke EIP, Berton JKET, Battilocchio C, Ley SV, Stevens CV (2016) Taming hazardous chemistry by continuous flow technology. Chem Soc Rev 45:4892–4928
Plutschack MB, Bartholomäus P, Gilmore K, Seeberger PH (2017) The Hitchhiker’s guide to flow chemistry. Chem Rev 117:11796–11893
Gérardy R, Emmanuel N, Toupy T, Kassin V, Tshibalonza NN, Schmitz M, Monbaliu JM (2018) Continuous flow organic chemistry: successes and pitfalls at the interface with current societal challenges. Eur J Org Chem 2018:2301–2351
Watson WJW (2012) How do the fine chemical, pharmaceutical, and related industries approach green chemistry and sustainability? Green Chem 14:251–259
Lee SL, O’Connor TF, Yang X, Cruz CN, Chatterjee S, Madurawe RD, Moore CMV, Yu LX, Woodcock J (2015) modernizing pharmaceutical manufacturing: from batch to continuous production. J Pharm Innov 10:191–199
Leahy DK, Tucker JL, Mergelsberg I, Dunn PJ, Kopach ME, Purohit VC (2013) Seven important elements for an effective green chemistry program: an IQ consortium perspective. Org Process Res Dev 17:1099–1109
Pieber B, Kappe CO (2015) Aerobic oxidations in continuous flow. Top Organomet Chem 57:97–136
Gemoets HPL, Su Y, Shang M, Hessel V, Luque R, Noel T (2016) Liquid phase oxidation chemistry in continuous-flow microreactors. Chem Soc Rev 45:83–117
Hone CA, Roberge DM, Kappe CO (2017) The use of molecular oxygen in pharmaceutical manufacturing: is flow the way to go? ChemSusChem 10:32–41
Battino R, Rettich TR, Tominaga T (1983) Solubility of oxygen and ozone in liquids. J Phys Chem Ref Data 12:163–178
Henry W (1803) lll. Experiments on the quantity of gases absorbed by water, at different temperatures, and under different pressures. Phil Trans R Soc Lond 93:29–274
Mallia CJ, Baxendale IR (2016) The use of gases in flow synthesis. Org Process Res Dev 20:327–360
Yue J, Chen G, Yuan Q, Luo L, Gonthier Y (2007) Hydrodynamics and mass transfer characteristics in gas–liquid flow through a rectangular microchannel. Chem Eng Sci 62:2096–2108
Hartman RL, McMullen JP, Jensen KF (2011) Deciding whether to go with the flow: evaluating the merits of flow reactors for synthesis. Angew Chem Int Ed 50:7502–7519
Gavriilidis A, Constantinou A, Hellgardt K, Hii KKM, Hutchings GJ, Brett GL, Kuhn S, Marsden SP (2016) Aerobic oxidations in flow: opportunities for the fine chemicals and pharmaceuticals industries. React Chem Eng 1:595–612
Osterberg PM, Niemeier JK, Welch CJ, Hawkins JM, Martinelli JR, Johnson TE, Root TW, Stahl SS (2015) Experimental limiting oxygen concentrations for nine organic solvents at temperatures and pressures relevant to aerobic oxidations in the pharmaceutical industry. Org Process Res Dev 19:1537–1543
Pratt TH (1993) Electrostatic ignitions in enriched oxygen atmospheres: a case history. Process Saf Prog 12:203–205
Veser K (2001) Experimental and theoretical investigation of H oxidation in a high-temperature catalytic microreactor. AIChE J 56:1265–1273
Thomas ML, Fraga-Dubreuil J, Coote AS, Poliakoff M (2008) A dramatic switch in selectivity in the catalytic dehydrogenation of 4-vinylcyclohexene in high pressure steam; a cautionary lesson for continuous flow reactions. Green Chem 10:197–201
Kockmann N, Thenée P, Fleischer-Trebes C, Laudadio G, Noël T (2017) Safety assessment in development and operation of modular continuous-flow processes. React Chem Eng 2:258–280
Anderson NG (2012) Using continuous processes to increase production. Org Process Res Dev 16:852–869
Wang D, Weinstein AB, White PB, Stahl SS (2018) Ligand-promoted palladium-catalyzed aerobic oxidation reactions. Chem Rev 118:2636–2679
Jin LQ, Lei AW (2012) Mechanistic aspects of oxidation of palladium with O2. Sci China Chem 55:2027–2035
Ye X, Johnson MD, Diao T, Yates MH, Stahl SS (2010) Development of safe and scalable continuous-flow methods for palladium-catalyzed aerobic oxidation reactions. Green Chem 12:1180–1186
Hone CA, O’Kearney-McMullan A, Munday R, Kappe CO (2017) A continuous-flow process for palladium-catalyzed olefin cleavage by using oxygen within the explosive regime. ChemCatChem 9:3298–3302
Gutmann B, Elsner P, Cox DP, Weigl U, Roberge DM, Kappe CO (2016) Towards the synthesis of noroxymorphone via aerobic palladium-catalyzed continuous flow N-demethylation strategies. ACS Sustain Chem Eng 4:6048–6061
Roberge DM, Gottsponer M, Eyholzer M, Kockmann N (2009) Industrial design, scale-up, and use of microreactors. Chim Oggi 27:8–11
Constable DJC, Dunn PJ, Hayler JD, Humphrey GR, Leazer JL Jr, Linderman RJ, Lorenz K, Manley J, Pearlman BA, Wells A, Zaks A, Zhang TY (2007) Key green chemistry research areas? A perspective from pharmaceutical manufacturers. Green Chem 9:411–420
Erdmann N, Su Y, Bosmans B, Hessel V, Noel T (2016) Palladium-catalyzed aerobic oxidative coupling of O-xylene in flow: a safe and scalable protocol for cross-dehydrogenative coupling. Org Process Res Dev 20:831–835
Izawa Y, Stahl SS (2010) Aerobic oxidative coupling of o-xylene: discovery of 2-fluoropyridine as a ligand to support selective Pd-catalyzed. Adv Synth Catal 352:3223–3229
Gemoets HPL, Hessel V, Noël T (2014) Aerobic C–H olefination of indoles via a cross-dehydrogenative coupling in continuous flow. Org Lett 16:5800–5803
Hone CA, Lopatka P, Munday R, O’Kearney-McMullan A, Kappe CO (2018) Continuous-flow synthesis of aryl aldehydes by Pd-catalyzed formylation of aryl bromides using carbon monoxide and hydrogen. ChemSusChem. https://doi.org/10.1002/cssc.201802261
Chen Y, Hone CA, Gutmann B, Kappe CO (2017) Continuous flow synthesis of carbonylated heterocycles via Pd-catalyzed oxidative carbonylation using CO and O2 at elevated temperature and pressure. Org Process Res Dev 21:1080–1087
Wendlandt AE, Suess AM, Stahl SS (2011) Copper-catalyzed aerobic oxidative C–H functionalizations: trends and mechanistic insights. Angew Chem Int Ed 50:11062–11087
Greene JF, Hoover JM, Mannel DS, Root TW, Stahl SS (2013) Continuous-flow aerobic oxidation of primary alcohols with a copper(I)/TEMPO catalyst. Org Process Res Dev 17:1247–1251
Vanoye L, Pablos M, De Bellefon C, Favre-Réguillon A (2015) Gas-liquid segmented flow microfluidics for screening copper/tempo-catalyzed aerobic oxidation of primary alcohols. Adv Synth Catal 357:739–746
Gutmann B, Elsner P, Roberge D, Kappe CO (2013) Homogeneous liquid-phase oxidation of ethylbenzene to acetophenone in continuous flow mode. ACS Catal 3:2669–2676
Pieber B, Kappe CO (2013) Direct aerobic oxidation of 2-benzylpyridines in a gas–liquid continuous-flow regime using propylene carbonate as a solvent. Green Chem 15:320–324
Vanoye L, Aloui A, Pablos M, Philippe R, Percheron A, Favre-Réguillon A, De Bellefon C (2013) A safe and efficient flow oxidation of aldehydes with O2. Org Lett 15:5978–5981
Vanoye L, Pablos M, Smith N, De Bellefon C, Favre-Réguillon A (2014) Aerobic oxidation of aldehydes: selectivity improvement using sequential pulse experimentation in continuous flow microreactor. RSC Adv 4:57159–57163
Vanoye L, Wang J, Pablos M, De Bellefon C, Favre-Réguillon A (2016) Continuous, fast, and safe aerobic oxidation of 2-ethylhexanal: pushing the limits of the simple tube reactor for a gas/liquid reaction. Org Process Res Dev 20:90–94
Vanoye L, Wang J, Pablos M, de Bellefon C, Favre-Réguillon A (2016) Epoxidation using molecular oxygen in flow: facts and questions on the mechanism of the Mukaiyama epoxidation. Catal Sci Technol 6:4724–4732
Guo S, Yu Z, Yu C (2018) Kilogram-scale synthesis of 2,4-dichloro-5-fluorobenzoic acid by air oxidation under the continuous-flow process. Org Process Res Dev 22:252–256
Munirathinam R, Huskens J, Verboom W (2015) Supported catalysis in continuous-flow microreactors. Adv Synth Catal 357:1093–1123
Campanati M, Fornasari G, Vaccari A (2003) Fundamentals in the preparation of heterogeneous catalysts. Catal Today 77:299–314
Cantillo D, Kappe CO (2015) Immobilized transition metals as catalysts for cross-couplings in continuous flow—a critical assessment of the reaction mechanism and metal leaching. ChemCatChem 6:3286–3305
Parmeggiani C, Matassini C, Cardona F (2017) A step forward towards sustainable aerobic alcohol oxidation: new and revised catalysts based on transition metals on solid supports. Green Chem 19:2030–2050
Zotova N, Hellgardt K, Kelsall GH, Jessiman AS, Hii KKM (2010) Catalysis in flow: the practical and selective aerobic oxidation of alcohols to aldehydes and ketones. Green Chem 12:2157–2163
Mannel DS, Stahl SS, Root TW (2014) Continuous flow aerobic alcohol oxidation reactions using a heterogeneous Ru(OH)x/Al2O3 catalyst. Org Process Res Dev 18:1503–1508
Obermayer D, Balu AM, Romero AA, Goessler W, Luque R, Kappe CO (2013) Nanocatalysis in continuous flow: supported iron oxide nanoparticles for the heterogeneous aerobic oxidation of benzyl alcohol. Green Chem 15:1530–1537
Liu X, Ünal B, Jensen KF (2012) Heterogeneous catalysis with continuous flow microreactors. Catal Sci Technol 2:2134–2138
Durndell LJ, Cucuzzella C, Parlett CMA, Isaacs MA, Wilson K, Lee AF (2018) Platinum catalysed aerobic selective oxidation of cinnamaldehyde to cinnamic acid. Catal Today. https://doi.org/10.1016/j.cattod.2018.02.052
Wang N, Matsumoto T, Ueno M, Miyamura H, Kobayashi S (2009) A gold-immobilized microchannel flow reactor for oxidation of alcohols with molecular oxygen. Angew Chem Int Ed 48:4744–4746
Sankar M, Dimitratos N, Miedziak PJ, Wells PP, Kiely J, Hutchings GJ (2012) Designing bimetallic catalysts for a green and sustainable future. Chem Soc Rev 41:8099–8139
Wu G, Brett GL, Cao E, Constantinou A, Ellis P, Kuhn S, Hutchings GJ, Bethell D, Gavriilidis A (2016) Oxidation of cinnamyl alcohol using bimetallic Au–Pd/TiO2 catalysts: a deactivation study in a continuous flow packed bed microreactor. Catal Sci Technol 6:4749–4758
Mannel DS, Ahmed MS, Root TW, Stahl SS (2017) Discovery of multicomponent heterogeneous catalysts via admixture screening: PdBiTe catalysts for aerobic oxidative esterification of primary alcohols. J Am Chem Soc 139:1690–1698
Watson DJ, Dowdy ED, Depue JS, Kotnis AS, Leung S, Reilly BCO (2004) Development of a safe and scalable oxidation process for the preparation of 6-hydroxybuspirone: application of in-line monitoring for process ruggedness and product quality. Org Process Res Dev 8:616–623
Laporte TL, Hamedi M, Depue JS, Shen L, Watson D, Hsieh D (2008) Development and scale-up of three consecutive continuous reactions for production of 6-hydroxybuspirone. Org Process Res Dev 12:956–966
Pieber B, Martinez ST, Cantillo D, Kappe CO (2013) In situ generation of diimide from hydrazine and oxygen: continuous-flow transfer hydrogenation of olefins. Angew Chemie Int Ed 52:10241–10244
Feth MP, Rossen K, Burgard A (2013) Pilot plant PAT approach for the diastereoselective diimide reduction of artemisinic acid. Org Process Res Dev 17:282–293
Pieber B, Glasnov T, Kappe CO (2015) Continuous flow reduction of artemisinic acid utilizing multi-injection strategies-closing the gap towards a fully continuous synthesis of antimalarial drugs. Chem Eur J 21:4368–4376
Pieber B, Cox DP, Kappe CO (2016) Selective olefin reduction in thebaine using hydrazine hydrate and O2 under intensified continuous flow conditions. Org Process Res Dev 20:376–385
He Z, Jamison TF (2014) Continuous-flow synthesis of functionalized phenols by aerobic oxidation of Grignard reagents. Angew Chem Int Ed 53:3353–3357
De Angelis S, Hone CA, Degennaro L, Celestini P, Luisi R, Kappe CO (2018) Sequential α-lithiation and aerobic oxidation of an arylacetic acid—continuous-flow synthesis of cyclopentyl mandelic acid. J Flow Chem 8:109–116
Noël T, Hessel V (2013) Membrane microreactors: gas–liquid reactions made easy. ChemSusChem 6:405–407
Brzozowski M, O’Brien M, Ley SV, Polyzos A (2015) Flow chemistry: intelligent processing of gas–liquid transformations using a tube-in-tube reactor. Acc Chem Res 48:349–362
Bourne SL, Ley SV (2013) A continuous flow solution to achieving efficient aerobic anti-Markovnikov Wacker oxidation. Adv Synth Catal 355:1905–1910
Petersen TP, Polyzos A, Brien MO, Ulven T, Baxendale IR, Ley SV (2012) The oxygen-mediated synthesis of 1,3-butadiynes in continuous flow: using teflon AF-2400 to effect gas/liquid contact. ChemSusChem 5:274–277
Brzozowski M, Forni JA, Savage PG, Polyzos A (2015) The direct α-C(sp3)-H functionalisation of N-aryl tetrahydroisoquinolines via an iron-catalysed aerobic nitro-Mannich reaction and continuous flow processing. Chem Commun 51:334–337
Chaudhuri SR, Hartwig J, Kupracz L, Kodanek T, Wegner J, Kirschning A (2014) Oxidations of allylic and benzylic alcohols under inductively-heated flow conditions with gold-doped superparamagnetic nanostructured particles as catalyst and oxygen as oxidant. Adv Synth Catal 356:3530–3538
Park JH, Park CY, Kim MJ, Kim MU, Kim YJ, Kim GH, Park CP (2015) Continuous-flow synthesis of meta-substituted phenol derivatives. Org Process Res Dev 19:812–818
Hollmann F, Arends IWCE, Buehler K, Bruno B (2011) Enzyme-mediated oxidations for the chemist. Green Chem 13:226–265
Ringborg RH, Toftgaard Pedersen A, Woodley JM (2017) Automated determination of oxygen-dependent enzyme kinetics in a tube-in-tube flow reactor. ChemCatChem 9:3273
Tomaszewski B, Schmid A, Buehler K (2014) Biocatalytic production of catechols using a high pressure tube-in-tube segmented flow reactor. Org Process Res Dev 18:1516–1526
Yang L, Jensen KF (2013) Mass transport and reactions in the tube-in-tube reactor. Org Process Res Dev 17:927–933
Wu G, Constantinou A, Cao E, Kuhn S, Morad M, Sankar M, Bethell D, Hutchings GJ, Gavriilidis A (2015) Continuous heterogeneously catalyzed oxidation of benzyl alcohol using a tube-in-tube membrane microreactor. Ind Eng Chem Res 54:4183–4189
Constantinou A, Wu G, Corredera A, Ellis P, Bethell D, Hutchings GJ, Kuhn S, Gavriilidis A (2015) Continuous heterogeneously catalyzed oxidation of benzyl alcohol in a ceramic membrane packed-bed reactor. Org Process Res Dev 19:1973–1979
Wu G, Cao E, Ellis P, Constantinou A, Kuhn S, Gavriilidis A (2018) Development of a flat membrane microchannel packed-bed reactor for scalable aerobic oxidation of benzyl alcohol in flow. Chem Eng J 1–9
Greene JF, Preger Y, Stahl SS, Root TW (2015) PTFE-membrane flow reactor for aerobic oxidation reactions and its application to alcohol oxidation. Org Process Res Dev 19:858–864
Park CP, Kim DP (2010) Dual-channel microreactor for gas-liquid syntheses. J Am Chem Soc 132:10102–10106
Park CP, Maurya RA, Lee JH, Kim DP (2011) Efficient photosensitized oxygenations in phase contact enhanced microreactors. Lab Chip 11:1941–1945
Maurya RA, Park CP, Kim DP (2011) Triple-channel microreactor for biphasic gas-liquid reactions: photosensitized oxygenations. Beilstein J Org Chem 7:1158–1163
Ogilby PR (2010) Singlet oxygen: there is indeed something new under the sun. Chem Soc Rev 39:3181–3209
Ghogare AA, Greer A (2016) Using singlet oxygen to synthesize natural products and drugs. Chem Rev 116:9994–10034
Knowles JP, Elliott LD, Booker-Milburn KI (2012) Flow photochemistry: old light through new windows. Beilstein J Org Chem 8:2025–2052
Su Y, Straathof NJW, Hessel V, Noël T (2014) Photochemical transformations accelerated in continuous-flow reactors: basic concepts and applications. Chem Eur J 20:10562–10589
Cambié D, Bottecchia C, Straathof NJW, Hessel V, Noël T (2016) Applications of continuous-flow photochemistry in organic synthesis, material science, and water treatment. Chem Rev 116:10276–10341
Lévesque F, Seeberger PH (2011) Highly efficient continuous flow reactions using singlet oxygen as a “Green” reagent. Org Lett 13:5008–5011
Lévesque F, Seeberger PH (2012) Continuous-flow synthesis of the anti-malaria drug artemisinin. Angew Chem Int Ed 51:1706–1709
Kopetzki D, Lévesque F, Seeberger PH (2013) A continuous-flow process for the synthesis of artemisinin. Chem Eur J 19:5450–5456
Loponov KN, Lopes J, Barlog M, Astrova EV, Malkov AV, Lapkin AA (2014) Optimization of a scalable photochemical reactor for reactions with singlet oxygen. Org Process Res Dev 18:1443–1454
Su Y, Kuijpers K, Hessel V, Noël T (2016) A convenient numbering-up strategy for the scale-up of gas–liquid photoredox catalysis in flow. React Chem Eng 1:73–81
Laudadio G, Govaerts S, Wang Y, Ravelli D, Koolman HF, Fagnoni M, Djuric SW, Noël T (2018) Selective C(sp3)–H aerobic oxidation enabled by decatungstate photocatalysis in flow. Angew Chem Int Ed 57:4078–4082
Yoshida J, Kataoka K, Horcajada R, Nagaki A (2008) Modern strategies in electroorganic synthesis. Chem Rev 108:2265–2299
Horn EJ, Rosen BR, Baran PS (2016) Synthetic organic electrochemistry: an enabling and innately sustainable method. ACS Cent Sci 2:302–308
Folgueiras-Amador AA, Wirth T (2017) Perspectives in flow electrochemistry. J Flow Chem 7:94–95
Atobe M, Tateno H, Matsumura Y (2018) Applications of flow microreactors in electrosynthetic processes. Chem Rev 118:4541–4572
Pletcher D, Green RA, Brown RCD (2018) Flow electrolysis cells for the synthetic organic chemistry laboratory. Chem Rev 118:4573–4591
Mo Y, Jensen KF (2018) Continuous N-hydroxyphthalimide (NHPI)-mediated electrochemical aerobic oxidation of benzylic C-H bonds. Chem Eur J 24:10260–10265
Sambiagio C, Sterckx H, Maes BUW (2017) Electrosynthesis: a new frontier in aerobic oxidation? ACS Cent Sci 3:686–688
Sheldon RA (2005) Green solvents for sustainable organic synthesis: state of the art. Green Chem 7:267–268
Henderson RK, Jiménez-González C, Constable DJC, Alston SR, Inglis GGA, Fisher G, Sherwood J, Binks SP, Curzons AD (2011) Expanding GSK’s solvent selection guide—embedding sustainability into solvent selection starting at medicinal chemistry. Green Chem 13:854
Alder CM, Hayler JD, Henderson RK, Redman AM, Shukla L, Shuster E, Sneddon HF (2016) Updating and further expanding GSK’s solvent sustainability guide. Green Chem 18:3879–3890
Diorazio LJ, Hose DRJ, Adlington NK (2016) Toward a more holistic framework for solvent selection. Org Process Res Dev 20:760–773
Byrne FP, Jin S, Paggiola G, Petchey THM, Clark JH, Farmer TJ, Hunt AJ, Mcelroy CR, Sherwood J (2016) Tools and techniques for solvent selection: green solvent selection guides. Sustainable chemical processes. Springer, Berlin, pp 1–24
Horváth IT (1998) Fluorous biphase chemistry. Acc Chem Res 31:641–650
Gunasekaran N (2015) aerobic oxidation catalysis with air or molecular oxygen and ionic liquids. Adv Synth Catal 357:1990–2010
Rayner CM (2007) The potential of carbon dioxide in synthetic organic chemistry. Org Process Res Dev 11:121–132
Leitner W (2002) Supercritical carbon dioxide as a green reaction medium for catalysis. Acc Chem Res 35:746–756
Medina-Gonzalez Y, Camy S, Condoret J-S (2014) ScCO2/green solvents: biphasic promising systems for cleaner chemicals manufacturing. ACS Sustain Chem Eng 2:2623–2636
Hintermair U, Roosen C, Kaever M, Kronenberg H, Thelen R, Aey S, Leitner W, Greiner L (2011) A versatile lab to pilot scale continuous reaction system for supercritical fluid processing. Org Process Res Dev 15:1275–1280
Hou Z, Theyssen N, Brinkmann A, Leitner W (2005) Biphasic aerobic oxidation of alcohols catalyzed by poly(ethylene glycol)-stabilized palladium nanoparticles in supercritical carbon dioxide. Angew Chem Int Ed 44:1346–1349
Chapman AO, Akien GR, Arrowsmith NJ, Licence P, Poliakoff M (2010) Continuous heterogeneous catalytic oxidation of primary and secondary alcohols in scCO2. Green Chem 12:310–315
Han X, Bourne RA, Poliakoff M, George MW (2011) Immobilised photosensitisers for continuous flow reactions of singlet oxygen in supercritical carbon dioxide. Chem Sci 2:1059–1067
Amara Z, Bellamy JFB, Horvath R, Miller SJ, Beeby A, Burgard A, Rossen K, Poliakoff M, George MW (2015) Applying green chemistry to the photochemical route to artemisinin. Nat Chem 7:489–495
Wu L, Lee DS, Boufroura H, Poliakoff M (2018) Photooxidation of fulvenes in a continuous flow photoreactor using carbon dioxide as a solvent. ChemPhotoChem 2:580–585
Osako T, Torii K, Uozumi Y (2015) Aerobic flow oxidation of alcohols in water catalyzed by platinum nanoparticles dispersed in an amphiphilic polymer. RSC Adv 5:2647–2654
Garcia-Verdugo E, Venardou E, Thomas WB, Whiston K, Partenheimer W, Hamley PA, Poliakoff M (2004) Is it possible to achieve highly selective oxidations in supercritical water? Aerobic oxidation of methylaromatic compounds. Adv Synth Catal 346:307–316
Pérez E, Fraga-Dubreuil J, García-Verdugo E, Hamley PA, Thomas WB, Housley D, Partenheimer W, Poliakoff M (2011) Selective aerobic oxidation of para-xylene in sub- and supercritical water. Part 1. Comparison with ortho-xylene and the role of the catalyst. Green Chem 13:2389
Pérez E, Fraga-Dubreuil J, García-Verdugo E, Hamley PA, Thomas ML, Yan C, Thomas WB, Housley D, Partenheimer W, Poliakoff M (2011) Selective aerobic oxidation of para-xylene in sub- and supercritical water. Part 2. The discovery of better catalysts. Green Chem 13:2397
Liguori L, Bjørsvik H-R (2011) Multijet oscillating disc millireactor: a novel approach for continuous flow organic synthesis. Org Process Res Dev 15:997–1009
Spaccini R, Liguori L, Punta C, Bjørsvik HR (2012) Organocatalyzed epoxidation of alkenes in continuous flow using a multi-jet oscillating disk reactor. ChemSusChem 5:261–265
Ioannou GI, Montagnon T, Kalaitzakis D, Pergantis SA, Vassilikogiannakis G (2017) A novel nebulizer-based continuous flow reactor: introducing the use of pneumatically generated aerosols for highly productive photooxidations. ChemPhotoChem 1:173–177
Ioannou GI, Montagnon T, Kalaitzakis D, Pergantis SA, Vassilikogiannakis G (2017) Synthesis of cyclopent-2-enones from furans using a nebulizer-based continuous flow photoreactor. Org Biomol Chem 15:10151–10155
Britton J, Stubbs KA, Weiss GA, Raston CL (2017) Vortex fluidic chemical transformations. Chem Eur J 23:13270–13278
Pye SJ, Dalgarno SJ, Chalker JM, Raston CL (2018) Organic oxidations promoted in vortex driven thin films under continuous flow. Green Chem 20:118–124
Lee DS, Amara Z, Clark CA, Xu Z, Kakimpa B, Morvan HP, Pickering SJ, Poliakoff M, George MW (2017) Continuous photo-oxidation in a vortex reactor: efficient operations using air drawn from the laboratory. Org Process Res Dev 21:1042–1050
Shvydkiv O, Limburg C, Nolan K, Oelgemöller M (2012) Synthesis of juglone (5-Hydroxy-1,4-Naphthoquinone) in a falling film microreactor. J Flow Chem 2:52–55
Jähnisch K, Dingerdissen U (2005) Photochemical generation and [4 + 2]-cycloaddition of singlet oxygen in a falling-film microreactor. Chem Eng Technol 28:426–427
Open access funding provided by University of Graz. The CCFLOW Project (Austrian Research Promotion Agency FFG No. 862766) is funded through the Austrian COMET Program by the Austrian Federal Ministry of Transport, Innovation and Technology (BMVIT), the Austrian Federal Ministry of Science, Research and Economy (BMWFW), and by the State of Styria (Styrian Funding Agency SFG). We are grateful to Dr. Doris Dallinger for carefully proofreading this chapter.
This article is part of the Topical Collection “Sustainable Flow Chemistry”, edited by Timothy Noel and Rafael Luque.
The original version of this article was revised: The publisher regrets that due to a conversion problem there were mistakes in this article.
About this article
Cite this article
Hone, C.A., Kappe, C.O. The Use of Molecular Oxygen for Liquid Phase Aerobic Oxidations in Continuous Flow. Top Curr Chem (Z) 377, 2 (2019). https://doi.org/10.1007/s41061-018-0226-z
- Continuous flow
- Flow reactor
- Continuous processing
- Aerobic oxidation
- Molecular oxygen
- Process intensification
- Green solvents