Abstract
One of the key challenges in the implementation of discrete element method (DEM) to model powder’s flow is the appropriate selection of material parameters, where empirical approaches are mostly applied. The aim of this study is to develop an alternative systematic numerical approach that can efficiently and accurately predict the influence of different DEM parameters on various sought macroscopic responses, where, accordingly, model validation based on experimental data is applied. Therefore, design of experiment and multivariate regression analysis, using an optimized quadratic Doptimal design model and new analysis tools, i.e., adjusted response and Pareto graphs, are applied. A special focus is laid on the impact of six DEM microscopic input parameters (i.e., coefficients of static and rolling friction, coefficient of restitution, particle size, Young’s modulus and cohesion energy density) on five macroscopic output responses (i.e., angle of repose, porosity, mass flow rate, translational kinetic energy and computation time) using angle of repose tests applied to freeflowing and cohesive powders. The underlying analyses and tests show, for instance, the substantial impact of the rolling friction coefficient and the minor role of the static friction coefficient or the particle size on the angle of repose in cohesive powders. In addition, in both powders, the porosity parameter is highly influenced by the static and rolling friction coefficients.
Introduction
One of the big challenges in the pharmaceutical industry is to optimize the powder solid handling process performance. This significantly relies on the flowability of the granular material in different process stages including hopper discharge, powder feeding, blending, mixing and die filling. Flowability, which describes the behavior of powder, is dependent on a range of fundamental powder properties. The flow properties of powders can be affected by various essential particle properties, including mean particle size and distribution, particle shape, surface roughness and moisture content. Powder flow also depends on the interparticle interactions where, for instance, flowability decreases with increasing cohesiveness of the powder. According to Parker et al. [1], cohesion is defined as the bonding or joining of two particles of the same material. A bulk solid with poor flowability is considered to be cohesive, which is due to the relatively high interparticle forces compared to the particle weight [2]. The inherent strength of the interparticle forces of attraction (often called cohesive forces) is derived from a combination of van der Waals forces and electrostatic charge on the surface of the particles. These forces hold particles close to their neighbors and thus result in the formation of agglomerates. Capillary force (liquid bridge), van der Waals force, electrostatic force and the weight force are all considered as adhesive forces, mainly interparticle forces between the particles and the wall. Understanding the physical meaning of these properties and their impact on the final product design is crucial in the development and successful production of solid dosage forms.
During their operation, industrial machines dealing with powders might encounter diverse problems which, due to their complexity, are most of the time difficult to analyze by traditional means. Therefore, many studies are extensively applied to optimize their operations, to deeply understand their functionalities, and to predict possible defects. For modeling a granular material, several numerical approaches on different scales and with different degrees of complexity and computational costs can be found in the literature. The microscopic discrete element method (DEM) (Cundall and Strack [3]) accounts for the most popular schemes and provides an effective approach for the understanding of granular material’s mechanical behavior and flowability on the microscale. In particular, DEM is a particlebased method used to model movement and interaction of bulk material [2]. Each particle is treated individually and its motion is described by Newton’s equation of motion. A softsphere approach is used, where colliding particles are allowed to slightly overlap resulting in a repulsive force [4]. DEM has been proven to be an important and efficient tool in several fields such as powder metallurgy, chemical engineering, pharmaceuticals and agriculture. To mention some, DEM simulations have been applied in granularrelated processes such as die filling [5], bulk compression [6], powder mixing [7], particles packing [8, 9], agglomerates fragmentation [10], flow in screw conveyor [11,12,13] and outflow from a hopper. Apart from DEM, other approaches, such as continuum porous media mechanics, can be applied to compute granular material mechanical responses on larger (macroscopic) scales and capture important behaviors such as wave propagation or fracture [14,15,16]. However, these approaches assume the continuity of the matter and cannot explicitly capture the interactions between the particles. Therefore, the focus in this work would be merely on DEM approach.
One of the most challenging aspects in applying efficiently the DEM numerical approach is choosing the appropriate contact models and then finding the right values of the input particle parameters involved in any used model. As particles introduced in granular materials are considerably small in size, measuring the properties of every single particle is considered very costly, challenging and timeconsuming. Yet, some trials using atomic force microscopy have been given to measuring the individual particles’ yield stress [17], Young’s modulus (Y) [18] and interfacial energy [19]. The stateoftheart approaches for calibration of DEM parameters in most cases are based on the trialanderror, where the track of the calibration process is lost in many cases by the human calibrators, especially when many factors are involved [20]. It is often the case that the DEM model is calibrated against bulk measurements and the input parameters are adjusted until the outputs of the model match with the experimental observations [21]. Therefore, it is of great interest for researchers to optimize the process of calibration. In the literature, different tools for DEM parameters calibration, some of which are (semi)automatized, can be found. AlHashemi et al. [22] presented an extensive review related to the angle of repose (AoR), methods of measurements, appropriate applications and the influencing factors of different parameters. Coetzee [23] discussed different DEM calibration approaches covered in the literature over the last 25 years to assist future researchers to improve on the existing ones. Liu et al. [24] investigated the impact of particle aspect ratio on the DEM simulation output in studying powder flow from hoppers. The authors developed a modified description of the classic Beverloo equation. Zhou et al. [25] studied the influence of particle–particle and particle–wall coefficients of friction, i.e., static and sliding on the AoR of a sandpile test. They constructed a powerlaw relationship between measured AoR and the input parameters and showed that all friction coefficients followed a positive dependency, whereas particle size followed a significant negative dependency. Yan et al. [26] utilized a multilevel statistical analysis approach on hopper flow in DEM to study the influence of coefficients of friction and restitution, as well as Young’s modulus. Using principal component analysis (PCA), the empirical powerlaw approach was found to agree with a semiempirical, which compared AoR to contact model parameter sensitivity matrices. The results in all cases showed that the coefficient of static friction was the critical parameter, which allows the gap to be bridged between bulk and interparticle interactions. In addition, it is shown that reducing the shear modulus (i.e., from 10^{7} and 10^{11} Pa) proved to have an insignificant effect on the powder flowability using freeflowing material which was also proven by Lommen et al. [27].
Boukouvala et al. [28] used a reducedorder approach to assess the importance of DEM parameters where PCA was coupled with surrogate models mapping which identified key areas of sensitivity. Major principal components enabled a reduced and computationally more efficient model to be engaged for future simulations. El Kassem et al. [29] calibrated the AoR of a pharmaceutical powder by varying coefficients of rolling friction and restitution using DoE, while determining the coefficient of static friction using the FT4 powder rheometer. Souihi et al. [30] used a statistical design of experiments (DoE) to provide a more efficient approach in investigating roller compaction. Orthogonal partial least squares (PLS) regression was used to analyze the results of a reduced central composite facecentered design in DoE. Wilkinson et al. [31] added that such approach using regression analysis has not been used so far for DEM simulations, but is highly recommended for developing more universal models for particle flow in a more efficient way. He proved that the Y has a negative impact on flow energy under specific conditions using a cohesive material. In this work, the effect of Y with the combination of varying the particle size in the same design model is studied which was not covered by [26] and [31]. To add up, Johnstone [32] used DoE to perform different calibration and validation methods based on experimental measurements. Benvenuti et al. [33] used artificial neural network to identify DEM simulation parameters. However, Rackl et al. [34] used a methodical calibration approach based on Latin hypercube sampling and Kriging, where they showed that different parameter combinations might lead to similar results. Wei et al. [35] studied the effect of three particle shapes on the AoR and bottom porosity distribution of a heap formed by natural piling using DEM. They found that the static friction has the major impact on the AoR and the porosity followed with the particle shape. Moreover, Li et al. [36] investigated the influence of three factors, namely moisture content, rice velocity and depth of the rice layer on the porosity of the flowing rice layer based on mass conservation and the poroelasticity theory. These results showed that the latter three factors have a significant influence on the porosity. Cheng et al. [37] developed a DEM calibration approach of granular soils based on the sequential quasiMonte Carlo (SQMC) filter. They calibrated the micromechanical parameters of the contact laws against the stress–strain behavior of Toyoura sand in drained triaxial compression conditions at different confining pressures. Do et al. [38] developed two automated DEM calibration approaches using genetic and direct optimization algorithms.
Moreover, in addition to the calibration process, one of the existing challenges in DEM is the high computational cost needed to perform real industrialscale simulations because of the extremely large number of particles being studied simultaneously at every time step. One of the most efficient approaches utilized to overcome this “obstacle” is to scale up the particle sizes and thus, reduce the total number of particles in the system according to coarsegraining method [39,40,41,42,43]. The most challenging issue in following such a method lies in adapting the material properties in such a way that compensates for the enlargement of the particles. In this study, the coarsegraining scheme proposed by Bierwisch et al. [42] was applied. The basis of this scheme is the preservation of the kinetic and gravitational potential energy densities as well as the volume fraction of particles as the original system with unscaled particles.
In this study, a novel simplified semiautomated parametric study and calibration approach is developed using an optimized multivariate regression analysis (MVRA). Initially, experimental powder characterization and AoR tests are performed. DoE method, using quadratic Doptimal design model, are applied for the sake of minimizing the number of simulations in an optimized way that retains high significance by recommending suitable possible combinations between DEM microscopic input parameters that should be tested together. The Doptimal design proved its efficiency by building a robust model by saving a lot of time and efforts compared to other models that require much more data points such as full factorial design. The proposed simulation runs from the DoE were performed in a parallel manner by implementing a code programming through the opensource software LIGGGHTS^{®} [44]. The studied microscopic input parameters are the coefficients of static and rolling friction, coefficient of restitution, particle size, Young’s modulus and cohesion energy density. The effects of these input parameters on five macroscopic output responses (targets), i.e., AoR, porosity, mass flow rate, translational kinetic energy and computation time, are studied through MVRA, using Cornerstone software, to find out which parameters and in what sense do they influence these targets. This systematic approach was done for a freeflowing powder and a cohesive powder, namely SpheroLac 100 and Inhalac 251, respectively. This method gives a more robust understanding of the impact of the interparticle input parameters on the flowability of the powders at different ranges (low, center and high) by tuning them in a methodical way rather than trialanderror. Since it is possible to have the same AoR with various DEM input parameter combinations [45, 46], the porosity is measured along with the AoR in DEM simulations in order to determine a more reliable and practical value for the studied input parameters. Accordingly, a prediction model is built to validate the regression analysis and to calibrate our experimental AoR and porosity values by selecting one optimized parameter combination.
Materials and methods
Materials
In this study, two pharmaceutical crystalline lactose monohydrate powders, purchased from MEGGLE Wasserburg GmbH & Co. KG (Germany), were selected. SpheroLac 100 was used to model the freeflowing powder, and InhaLac 251 was utilized to model the cohesive one. They are mainly characterized by different particle sizes, which in turn affect their flowability. SpheroLac 100 is mainly used in capsule filling, blends, premixes, sachets, triturations, whereas InhaLac 251 is a dry powder inhaler used in capsule or blisterbased formulations.
Experimental angle of repose (AoR)
The AoR is defined as the slope of a poured conical pile of loose uncompacted bulk solid material [18]. It is a characteristic related to the cohesiveness of the powder [47] and used as a common method to characterize powders according to their flowability [48,49,50,51]. It is a common method to calibrate DEM simulation parameters, where the angle at which a heap of powder settles depends on the strength of the interparticulate friction. This simple test case was chosen in order to perform a parametric study of the DEM microscopic input parameters. As depicted in Fig. 1, a funnel made of 1.4404 stainless steel was placed above a catching container made of borosilicate 3.3 glass. Initially, the funnel was loosely filled with 5 g of powder where the lower opening of the funnel was closed. Then, the funnel was opened to let the powder discharge under gravity forming a pile on the bottom of the catching container. The test for each powder was repeated five times, and an average of the obtained angles was considered as a value for the AoR for each powder.
Discrete element method (DEM)
In DEM, grains, referred to in the following as particles, are treated as rigid bodies, which have translational and rotational degrees of freedom assigned to their center of mass. In this study, the focus is on the behavior of the freeflowing and the dry cohesive powder particles. In the DEM, particle interactions are modeled using the wellestablished Newton’s equations of motion, contact laws and overlap relationships. The softparticle approach, originally developed by Cundall and Strack [3], is followed in this work, where the particles are allowed to undergo small deformations, i.e., overlaps. Thereafter, these deformations are used to calculate the elastic and plastic deformations besides the frictional forces between the particles [4]. As two particles i and j come in contact with each other, different interactions, i.e., forces and torques due to gravity, deformations under collisions, as well as static and rolling frictions, might occur. Translational and rotational motion of particle i with mass \( m_{i} \) and moment of inertia \( I_{i} \) are represented by the following equations:
where \( \varvec{g} \), \( \varvec{v}_{i} \) and \( \varvec{\omega}_{i} \) are the gravity vector, translational velocity and rotational velocity of particle i, respectively. The interaction between particle i and j at a defined time step leads to normal and tangential forces, i.e., \( \varvec{F}_{ij}^{n} \) and \( \varvec{F}_{ij}^{t} \), respectively. \( \varvec{R}_{i } \) is the vector between the center of particle i and the contact point, where the tangential force \( \varvec{F}_{ij}^{t} \) is applied. \( \varvec{\tau}_{ij}^{r} \) is the torque due to rolling friction between the two particles.
Hertz–Mindlin contact model
Hertz–Mindlin [52, 53] contact law is the most common applied approach in modeling contacts between particles. It is used in calculating the contact forces introduced due to the slight considered overlap between particles. The frictional contact force between two granular particles i and j comprises normal \( \varvec{F}_{ij}^{n} \) and tangential \( \varvec{F}_{ij}^{t} \) nonlinear contact forces given as
Each contact force consists of two terms, where the first term stands for the nonlinear elastic Hertz model in the normal direction (spring force) and the linear elastic Mindlin model in the tangential direction (shear force). The second term stands for the damping force (modeled as a dashpot), where a dissipative term is added for both normal and tangential directions to account for energy dissipation during collisions through inelastic deformation and friction. The normal and tangential forces between two spheres i and j during a collision are given by
where \( k_{n} \) and \( k_{t} \) are the elastic constants for the normal and tangential contact, \( \varvec{\delta}_{ij}^{n} \) is the normal contact overlap, given by \( \varvec{\delta}_{ij}^{n}  = R_{i} + R_{j}  l_{ij} \), where \( l_{ij} \) is the distance between the centers of the two particles, \( \varvec{\delta}_{ij}^{t} \) is the tangential contact overlap or displacement vector which is truncated to satisfy a frictional yield criterion, given by the integral of the tangential relative velocity through the collision time they are in contact, i.e., \( \left {\varvec{\delta}_{ij}^{t} } \right = \mathop \smallint \limits_{0}^{t} \left {\varvec{v}_{ij}^{t} } \right{\text{d}}t \), \( \varvec{v}_{ij}^{n} \) and \( \varvec{v}_{ij}^{t} \) are the normal and tangential components of the relative velocity of the two particles at the contact, \( \gamma_{n} \) and \( \gamma_{t} \) are the viscoelastic damping constant for normal and tangential contact. Figure 2 illustrates the mechanical system of the interactions of particles in the Hertz–Mindlin contact model.
Under sufficient tangential forces, particles will slip relative to each other or relative to surfaces they are in contact with. For noncohesive particles subjected to a constant normal force, the extent of slippage under tangential force is determined by
where \( \mu_{\text{ss}} \), represented by a shear slider, is the static friction coefficient between the two particles in the tangential direction. Thus, the tangential force described by a spring and a damper is limited to the Coulomb friction.
Consequently, based on Eqs. (4) and (5), the normal and tangential forces, \( \varvec{F}_{ij}^{n} \) and \( \varvec{F}_{ij}^{t} \) can be expressed in detail as
where \( Y^{*} \) is the equivalent Young’s modulus of the two colliding particles. This is defined by \( \frac{1}{{Y^{*} }} = \frac{{1  v_{i}^{2} }}{{Y_{i} }} + \frac{{1  v_{j}^{2} }}{{Y_{j} }} \), where \( v_{i} \) and \( v_{j} \) are Poisson’s ratios, \( R^{*} \) is the equivalent radius, defined by \( \frac{1}{{R^{*} }} = \frac{1}{{R_{i} }} + \frac{1}{{R_{j} }} \), and \( m^{*} \) is the equivalent mass, defined by \( \frac{1}{{m^{*} }} = \frac{1}{{m_{i} }} + \frac{1}{{m_{j} }} \). Moreover, \( S_{n} = 2Y^{*} \sqrt {R^{*}\varvec{\delta}_{ij}^{n} } \) and \( S_{t} = 8G^{*} \sqrt {R^{*}\varvec{\delta}_{ij}^{n} } \) are the normal and tangential contact stiffness with \( G^{*} \) being the equivalent shear modulus, defined as \( \frac{1}{{G^{*} }} = \frac{{2\left( {2  v_{i} } \right)\left( {1 + v_{i} } \right)}}{{Y_{i} }} + \frac{{2\left( {2  v_{j} } \right)\left( {1 + v_{j} } \right)}}{{Y_{j} }} \). Besides, \( \beta \) is the damping ratio coefficient, which is a function of the coefficient of restitution, \( e \), and given by \( \beta = \ln \left( e \right)/\sqrt {\ln^{2} \left( e \right) + \pi^{2} } \). The coefficient of restitution \( e \) is the ratio of relative velocity after collision to the relative velocity before collision. A value of \( e \) = 1 refers to a perfectly elastic collision, whereas \( e \) = 0 would mostly be an inelastic collision.
Rolling friction model
In addition to sliding friction, rolling friction is present as a contactdependent force [55]. Rolling friction is a major parameter that serves as a correction factor by compensating for the use of spherical particle shapes in DEM [56], instead of representing their actual shapes in reality. In the literature, different rolling resistance models have been developed and reviewed [56]. In this work, the alternative elastic–plastic springdashpot (EPSD2) rolling resistance model [57], implemented in LIGGGHTS opensource code, is applied to calculate the torque \( \varvec{\tau}_{ij,t + \Delta t}^{r} \) at an incremental time step as
where \( \mu_{r} \) is the rolling coefficient. In this model, the damping torque is disabled for simplicity.
Cohesion model
The modified simplified Johnson–Kendall–Roberts cohesion model (SJKR), implemented in LIGGGHTS, is used to model the cohesion of particles. This model originates from the JKR model [58], where it represents the influence of various cohesive forces, such as Van der Waals within the contact zone. It can model high adhesive systems, such as fine and dry powders or wet materials. It adds an additional normal force component \( F_{\text{coh}} \) to the Hertzian contact law tending to maintain a larger contact area (Fig. 3), i.e.
where \( C \) is the cohesion energy density in J m^{−3} and a is the particle contact area, given as
where \( R_{i} \) and \( R_{j} \) are the radii of sphere i and j, respectively, and \( l_{ij} \) is the distance between the particle centers.
Noncontact force
In addition to the contact forces, the gravitational acceleration \( g \) in the zdirection (with \( \hat{\varvec{z}} \) as the unit vector) yields the gravitational force of particle i, \( \varvec{F}_{i}^{\text{grav}} \), which can be expressed as
Time step in DEM simulation
In the DEM simulations of particles flow in this work, the time step \( \left( {\Delta t} \right) \) has been selected to be less than 20% of the critical time step (Rayleigh time) \( T_{\text{R}} \) in order to ensure the stability of the integration scheme. \( T_{\text{R}} \) is calculated based on the Rayleigh wave propagation, which represents the elastic wave propagation along the surface of one particle to the adjacent contacting particle according to the following equation [59]:
where ρ is the particle density, \( G \) is the shear modulus and \( \nu \) is the Poisson’s ratio.
Experimental material characterization
This section briefly describes the experimental methods used to find out some material parameters utilized in the DEM simulations. The parameters are divided into two categories: material parameters and interaction parameters [60]. The material parameters include the shape, size, density, elastic and shear modulus as well as Poisson’s ratio, whereas the interaction properties are coefficients of restitution, static and rolling frictions and adhesion.
Particle size and shape characterization
Camsizer XT from Retsch Technology GmbH (Germany) was used to measure the volume moment mean (D [3, 4]), which is also called De Brouckere Mean Diameter, and shape of particles via dynamic image analysis. The D [3, 4] indicates around which central point (center of gravity) of the frequency the volume/mass distribution would rotate. The advantage of this method over other particle sizes calculation methods is that it does not require the number of particles in its calculation.
The Camsizer XT helps in approximating the particle shape, where the particles are described in twodimensional images in terms of the minimum and maximum Feret diameters (Fe_{min}, Fe_{max}). Fe_{min} is the length of the minor axis and Fe_{max} is the length of the major axis. The ratio of Fe_{min} to Fe_{max} is called the aspect ratio (ASR). In this, the aspect ratio with values between 0 and 1 reflects the elongation of a particle and deviation from a sphere where small values correspond to elongated particles and higher values correspond to spherical particles:
According to Li et al. [61], a shape factor called circularity or roundness (R_{o}) is an additional factor that indicates to what extent a particle has a spherical shape. It is based on the projected area (A) of the particle and the overall perimeter of the projection (P) according to the following equation:
Density and porosity
The bulk density (BD) and the tapped density (TD) were analyzed via the jolting volumeter (Jel STAV II) from J. Engelsmann AG (Germany). A certain mass of powder was filled into a graduated cylinder, and the volume and mass were then recorded. The test was repeated five times to insure accuracy and repeatability where then an average value was considered. The bulk density represents the average density of the powder sample, where the bulk volume contains voids between individual particles. Therefore, the bulk density of a powder depends on both the material density of the particles and their spatial arrangement. The volume of a bulk solid depends on the size and the shape of the particles. Besides, the tapped density was attained after mechanically compacting the powder sample by up to 1250 taps.
The particle (true) density (ρ_{p}) was obtained using the Ultrapyc 1200e, Automatic Density Analyzer from Quantachrome Instruments (USA). It is a pycnometer that measures the true density of powder samples using an inert gas (helium) to measure its volume by applying Archimedes’ principle of displacement and the technique of gas expansion (Boyle’s law). Consequently, the powder bed porosity (ε) is calculated as described in the following equation:
Carr’s index
Based on the BD and TD, powder flowability of bulk solid could be characterized by the Carr’s index (CI), or Carr’s compressibility index [18]. CI is an indication of the compressibility of a powder, where larger changes indicate poor flowability [62]. It is a measurement of the relative difference between tapped volume and untapped volume of the powder [47], i.e.
Powders with \( {\text{CI}} < 15\% \) have good flowability, whereas a poor flowability corresponds to \( {\text{CI}} > 25 \)%.
Cohesion and flow function coefficient
FT4 powder rheometer from Freeman Technology Ltd (UK) was used to find out the cohesion (C) and flowing factor (\( ff_{\text{c}} \)) values. A commonly applied approach is the Mohr–Coulomb model that fits the Mohr stress circles to the yield locus that in turns identifies the major principal stress (\( {\text{MPS}} \)) and unconfined yield strength (\( {\text{UYS}} \)). In this, \( {\text{UYS}} \) is related to \( {\text{MPS}} \) via the material flow function coefficient \( ff_{\text{c}} \) as
Flow function \( ff_{\text{c}} \) is commonly used to describe the flowability of a bulk solid. In addition, the cohesion value is identified by the shear cell test [63]. This value is the shear stress at which the normal stress is equal to zero for the best fit of the shear and applied normal stress plot [64]. Generally, a cohesive powder will have higher values for cohesion and \( {\text{UYS}} \) and consequently a low \( ff_{\text{c}} \). In particular, \( ff_{\text{c}} \) values below 4 denote a very cohesive powder behavior (poor flowing), between 4 and 10 easyflowing powder and above 10 freeflowing powder.
Static friction
The shear cell test in the FT4 powder rheometer was executed to find out an approximation of the angle of internal friction (AIF) between particles based on the linearized yield locus of the material. It is the angle between the axis of normal stress (abscissa) and the tangent to the yield locus [65]. It measures the shear stress for various normal stresses to describe the magnitude of the shear stress that powder can sustain [65]. From this angle, the interparticle static friction coefficient, denoted by µ_{s,pp}, indicates the resistance between two contacting particles while being sheared [2]. This can be calculated as
Wall friction
The wall friction test, using the FT4 powder rheometer, provides a measurement of the sliding resistance between the powder and the surface of the process equipment [66]. This test is important for understanding the discharge behavior from a container, especially when using an auger. The measurement principle of a wall friction test is very similar to the shear cell test, where the powder is sheared against a material resembling process equipment wall and not against the powder. The process equipment wall used in this study is a rounded stainless steel disk with 0.05 µm surface roughness. The data from the test are represented as a plot of shear stress against normal stress, allowing to determine the wall friction angle (WFA). It is the arctan of the ratio of the wall shear stress to the wall normal stress [65]. The greater is the wall friction angle, the higher is the resistance between the powder and wall.
Similarly, the coefficient of static friction between a particle and wall (µ_{s,pw}) can be calculated from the wall friction angle as
Moisture content
According to Schulze [18], the holding forces or adhesive forces with the presence of liquid bridges (capillary force) are higher than any other holding forces in bulk materials, as long as the contact distance is very low. The content of moisture sheds the light on some characteristics such as cohesion or agglomeration tendency and can help to describe the flow behavior. The moisture content (MC) was experimentally determined by the halogen drying method using the Halogen Moisture Analyzer type HR73 from Mettler Toledo (USA). A sample amount was heated by a halogen lamp, and thus the moisture is extracted from the powder. Due to this drying process, the bulk loses some weight, and thus the moisture loss is calculated from the difference between the initial and final weights. This moisture loss corresponds to the moisture content of the powder in the initial state.
Coarsegraining method
To find a tradeoff between computational time and accuracy, it is reasonable to limit the number of particles in the DEM simulation. According to Bierwisch et al. [42], coarsegraining (CG) method is a good approach to save significant computational time but DEM simulations with good accuracy are performed in comparison with real tests. In the coarsegraining technique, the original particles with radius R are substituted by larger grains with radius \( R^{\prime} \). The scaledup radius \( R^{\prime} \) can be represented as a multiplication of the original grain radius R and a scaling factor S_{f}. Moreover, CG method is based on an appropriate adjustment of interaction laws and equations of motion according to scaling rules for the material parameters in such a way that the energy densities, i.e., gravitational potential and kinetic energy, are preserved in the scaledup system as the original one. As the potential density does not depend on the particle’s radius while maintaining a constant volume fraction and particle’s density, the particle’s density is ought to be fixed upon applying the CG method. According to the coarsegraining proposed by Bierwisch et al. [42], the volume fraction is not affected and, therefore, the potential energy of the scaled system is comparable to the original system. Consequently, the mass of each particle introduced in the system is scaled up by a factor of S ^{3}_{f} according to Eq. (21), but as the total number of particles is decreased also by the same factor, the total mass of the particles is conserved:
Bierwisch et al. [42] also proved that the energy dissipation per volume and time is preserved if the coefficient of restitution remains the same after applying the coarsegraining method. Thus, the kinetic energy density is preserved because the scaling does not affect particle velocities. In connection with the applied test in this study, i.e., AoR, it is shown that coarse graining has no considerable effect on the resulting angles. In addition, it was observed that the shape of the heap is changing with increasing the particles sizes, where a noticeable tail of the ground heap and a more procumbent peak could be seen for larger particles. Thus, although the CG method leads to highly acceptable results in terms of bulk properties, it is hard to get exactly the same shape of the heap in the DEM simulation after applying the CG method.
Design of experiment
Design of experiments (DoE) is a systematic technique of planning experiments that is used to determine the cause–effect relationship between factors affecting a process and its responses [67]. It can help in identifying the best combinations of parameters that yield to the desired results and, thus, optimizing the output [32]. The design space of the experiments, in our case simulations, is identified according to the design model used by efficiently selecting the suitable factors combinations to be tested. The DoE method is used to investigate the effects and interactions of DEM input parameters on the output responses, which in turn will facilitate the calibration process. Quadratic Doptimal design model was used to obtain the largest amount of information from the smallest number of simulations using Cornerstone 6.1.1.1 software from camLine GmbH (Germany). The mathematics behind Doptimal design is closely related to the Least Squares method to find the concrete model equation on the basis of the design and the response data.
Multivariate regression analysis
Multivariate regression analysis (MVRA) is a statistical technique applied to analyze the variation of more than one outcome variable and thus estimates a regression model. This technique was utilized to observe and analyze the variation and impact of different DEM input parameters on the output parameters. Cornerstone software was used, where the inserted data values are standardized; that is, the original variables are scaled to have a mean of 0 and a variance of 1 as each attribute has a different unit of measurement. The goodnessoffit of the statistical model was described by the adjusted R^{2} (coefficient of determination). R^{2} represents the proportion of the variability of the data explained by the model which is adjusted for the number of factors in the model. The confidence level used in the DoE analysis was ± 95%. An adjusted response graph was used to show the effect of each input parameter on the responses besides showing all data points of the simulation runs, which are not the real measured values but the adjusted ones. The response values are adjusted to average out the effects of the other input parameters. An additional tool in Cornerstone software is the Pareto graph. It expresses the relative size of the effect of each DEM input parameter studied in the model. It shows the orthogonal scaled effects of the factors on the studied responses. To add up, two prediction models based on the regression analysis were built for the sake of predicting an approximate value of the AoR in the freeflowing and cohesive powders.
DEM simulations
Simulation setup
The DEM simulations were performed using the opensource software LIGGGHTS^{®}Premium 4.X from DCS Computing GmbH (Linz, Austria). The simulations were carried out on an eightnode highperformance cluster using 32 CPUs (Intel Xeon 2.60 GHz). The postprocessing of the simulations was performed using ParaView, version 5.4.1 64bit from Kitware Inc. (New York, NY, USA). The threedimensional CAD models used in the DEM simulations were modeled in SolidWorks version Premium 2016 from Dassault Systèmes (VélizyVillacoublay, France). After that, the threedimensional models were meshed using Gmsh, version 3.0.6 [68].
DEM input parameters
Fixed parameters through the studies
In the DEM simulations, the Hertz–Mindlin contact model and the rolling friction model (EPSD2) were applied for both the freeflowing and the dry cohesive studies. The adhesion contact model (SJKR) was added to the cohesive study. The values of Young’s modulus (Y) and the Poisson’s ratio (ν) for the funnel and the catching container were selected from the literature [69]. The boundary conditions such as restitution and friction between particle and walls (funnel and glass in this case) were kept constant to reduce the number of simulations in the DoE. Table 1 lists the input parameters in the applied two DEM AoR studies.
Parameters varied in the design of experiments
In the freeflowing study, five particle properties were varied as part of the DoE which were as follows: particle’s Young’s modulus (Y), particle size (d), coefficient of restitution (e_{pp}), coefficient of static friction (µ_{s,pp}) and coefficient of rolling friction (µ_{r,pp}). In addition to these parameters, cohesion energy density (C_{pp}) was varied in the dry cohesion study. The latter four parameters are related to the particletoparticle interactions.
In the calibration process, the variation study of the parameters aimed to give the best fit between the DEM simulation and the corresponding reference data. To this end, the µ_{s,pp} was determined using the FT4 powder rheometer, but because of reducing the Y parameter due to computational limitations, this coefficient was calibrated to get the same bulk solid behavior [45, 70]. e_{pp} and µ_{r,pp} were also tuned because they are difficult to be determined for microscale powders. When using spherical particle shape, the rolling resistance is considered to be less dominant above the static friction as the contact area is smaller. The range value of the cohesion energy density was roughly estimated by performing presimulation runs or socalled initial screening investigations.
Table 2 lists the values of the six particle properties that were varied in our studies. Three values, which constitute a low, center and high levels for each parameter, were selected. The center values of e_{pp}, µ_{s,pp}, µ_{r,pp} and C_{pp} are linearly spaced between low and high values, whereas for Y, the center value is spaced on a logarithmic scale. The values of Y in the DoE are logarithmic where the simulation values 0.026, 0.26 and 2.6 GPa are set to 7.41, 8.41 and 9.41 log GPa to ensure a center point in the analysis.
Threelevel design was used where each factor was considered at three levels. For the freeflowing powder, 40 simulation runs were executed whereas 53 runs for the dry cohesive one.
DEM studied responses
In preparation of the mesh for the simulations, all the faces that have no contact with the particles were deleted in SolidWorks in order to optimize the computation time. Figure 4 shows the modified mesh file of the funnel in ParaView filled with spherical particles as an initial state before removing the stopper and allowing the particles to flow out.
Five macroscopic output responses, namely AoR, porosity (ε), mass flow rate (\( \dot{{m}} \)), overall translational kinetic energy (TKE) and the computation time (CT), on the two powders were studied. The porosity was measured in the funnel due to the simplicity in defining a common volume since no heap (zero AoR) was formed in some simulations. The \( \dot{\text{m}} \) at the discharge of the funnel was studied, where the mass values were measured every 25 ms. The overall translational kinetic energy (TKE) of the system was calculated over time to check how the dissipation of energy varies according to different simulation input combinations. The average of the TKE, after opening the funnel, was calculated and then normalized (NATKE) with the total discharge time of the particles. Table 3 reports the DoE followed and its simulation results of five output responses under the variation in five input parameters for the freeflowing powder.
Table 4 shows the DoE used and the corresponding results of five output responses under the variation in six input parameters for the cohesive powder.
Results and discussion
Material characterization
Table 5 presents the results of the particle size and shape, as well as the bulk properties of the two powders. Based on these material characterization results, the spherical form was selected to represent the particle’s shape in LIGGGHTS because both powders have high ASR and R_{o} values. The values of the ρ_{p} were used in the DEM setup. The low values of MC in the table prove that both powders are almost dry.
Table 6 lists the flowability values according to Carr’s index as well as the shear properties of the two studied powders. The results illustrate how SpheroLac 100 is considered a freeflowing powder because it has low CI, low C and high \( ff_{\text{c}} \). Conversely, InhaLac 251 has high CI, high C and low \( ff_{\text{c}} \) values and thus it is considered as a cohesive powder. The values of µ_{s,pp} were just set as reference values, whereas the values of µ_{s,pw} were used in the simulation setup.
Angle of repose experiment
The AoR for each experiment was calculated by taking the average value between the left and right angles, θ_{1} and θ_{2}, respectively. The obtained results of the AoR for both powders were set as reference values in the validation of the regression analysis in the prediction model and thus in the calibration approach. Figure 5 shows the heap formed by the AoR test of the freeflowing powder (SpheroLac 100) in the glasscatching container where the average angle was 33°.
On the contrary, the average AoR of the cohesive powder (InhaLac 251) was 40° where Fig. 6 shows the heap formed in the experiment.
Parametric study
Factors affecting angle of repose

Freeflowing
The average AoR for each simulation test was calculated. The values of AoR ranged between 0° and 39°, where in eight cases the AoR was equal to zero due to low µ_{s,pp} as listed in Table 3. Figure 7 presents numerical examples of six AoR DEM simulations for the freeflowing powder formed in the catching container.
The model of the AoR for the freeflowing powder showed an adjusted R^{2} = 0.954, indicating a very good fit to the data points. Figure 8a shows the adjusted response graph for the AoR. Each of the presented sections (columnwise) corresponds to an input parameter. In each section, all the data points obtained from simulations are presented in addition to the effect drawn from these points. For a data point, the effects of the other factors included in the model were averaged; therefore, the data points were adjusted in such a way that the effect of the corresponding factor on the response is only presented (adjusted response graph). As the data points were recalculated, it can be seen that the actual values of the responses listed in Table 3 do not match with the adjusted values, yet the effect of each parameter can still be modeled. Finally, scattering points signify data points that cannot be described by the model due to some noise effects.
From Fig. 8a, the following trends can be observed regarding AoR: Y and d_{S} have no significant effects on the AoR, e_{pp} and µ_{r,pp} have a slight effect and µ_{s,pp} has the major effect. The absence of d_{S} as an effective factor to the AoR ensures the correct implementation of the coarsegraining scheme proposed by Bierwisch in our system. Moreover, our results contradict many studies which proved that the particle size has an impact on the AoR [22, 25, 47].
Figure 9 illustrates the Pareto graph of effects on the AoR of the freeflowing powder where the largest positive effects are shown on the left and the largest negative effects on the right, with factors of smaller estimated effects in the middle of the graph. It can be seen that µ_{s,pp} has the highest positive effect (proportional) on the AoR, where, as µ_{s,pp} increases, the AoR increases as well. The rest of the affecting factors, i.e., µ_{r,pp} and e_{pp}, interactions (e.g., µ_{s,pp} * µ_{r,pp}), and quadratic terms (e.g., e ^{2}_{pp} ) have lower effect compared to that of µ_{s,pp}. To be stated, as e_{pp} increases, the AoR decreases, which is previously confirmed by Wei et al. [35]. As e_{pp} is the ratio of the relative velocity after collision to the relative velocity before collision of an object with a surface, the results can be explained by the fact that due to the high elasticity of the spherical particles, they can more likely bounce than to settle down along a free surface.

Cohesive
Figure 10 illustrates numerical examples of six AoR DEM simulations for the cohesive powder formed in the catching container.
The adjusted R^{2} of the AoR of the cohesive powder model has a very good value of 0.915. Figure 11a shows the adjusted response graph for the AoR. It indicates that the introduction of cohesion in the system through the SJKR model added a new affecting parameter on the AoR, which is Y. Unlike the freeflowing case, it is proved that Y has a significant negative effect on AoR when C_{pp} is involved. This ensures the importance of such a parametric study, where Y is not included in many other calibration processes due to its computational cost impact, though it has influence. From Fig. 11a, it can be seen that the angle of repose increases with an increase in the sliding and rolling friction coefficients, which is proven in other studies as well [25, 46, 71,72,73,74]. This positive correlation is similar in both freeflowing and cohesive powders.
Figure 12 demonstrates the Pareto graph of effects on the AoR of the cohesive powder. It shows that µ_{r,pp} has the highest positive effect on the AoR, which is contrary to most of the studies that proved the superiority of µ_{s,pp} in terms of effectivity. Therefore, it is very critical to always relate the effectiveness of the parameters to the circumference of the case study. Moreover, Y has a bigger impact on the AoR than µ_{s,pp}.
Factors affecting porosity

Freeflowing
The regression analysis of the ε of the freeflowing powder resulted in a very good adjusted R^{2} value of 0.981. The adjusted response graph of ε in Fig. 8b demonstrates the high significance positive correlation of µ_{s,pp} on ε followed with µ_{r,pp}, which was also proven by Wei et al. [35]. The other studied microscopic parameters indicated less significance, where the relative size of effects of these parameters is presented in Fig. 13.

Cohesive
The adjusted R^{2} of the ε of the cohesive powder was very good as well with a value of 0.983. Similarly to the freeflowing powder, µ_{s,pp} had the highest positive influence on ε followed with µ_{r,pp} as revealed in Fig. 11b. In addition, the Pareto graph of effect in Fig. 14 shows the superiority positive relative effect of µ_{s,pp} on ε compared to the other parameters.
Factors affecting mass flow rate

Freeflowing
The adjusted R^{2} of the \( \dot{\text{m}} \) model of the freeflowing powder was recorded to be 0.95. The adjusted response graph for the \( \dot{\text{m}} \) is shown in Fig. 8c. As observed, all the studied parameters affect the \( \dot{\text{m}} \), but each in a different way which is also presented in the Pareto graph (Fig. 15). The Pareto graph shows that µ_{s,pp} has the highest negative effect on the \( \dot{\text{m}} \). This indicates that as µ_{s,pp} increases, the particles’ flow out of the funnel gets delayed due to the sliding friction between the particles. The same holds for µ_{r,pp} and d_{S}. Unlike e_{pp}, as it increases, \( \dot{\text{m}} \) increases slightly.
Following this, the mass and \( \dot{\text{m}} \) of the six example simulations shown in Fig. 10 were plotted over time in one graph (Fig. 16) to compare them with each other. The parameter combinations and the mean \( \dot{\text{m}} \) values of each run are presented in Table 3.
Figure 16 shows that the slopes of mass graphs M_1 and M_9, corresponding to the first and ninth DEM simulations, have the highest \( \dot{\text{m}} \) while having the lowest values of µ_{s,pp} (0.1). M_8 is showing the lowest slope (\( \dot{{m}} \)) with the assignment of having a high value of µ_{s,pp} (0.85).

Cohesive
The model fit of the \( \dot{\text{m}} \) in the cohesive study was very good with an adjusted R^{2} = 0.957. Figure 11c presents the adjusted response graph for the \( \dot{\text{m}} \), and the Pareto graph (Fig. 17) shows the weight value effect of the input parameters on the \( \dot{\text{m}} \). It is apparently shown that \( \dot{\text{m}} \) has been highly negatively affected by µ_{s,pp}, µ_{r,pp} and d_{I} in decreasing order of effectivity. A lower but significant positive effect has been witnessed for Y. This is due to the fact that particles with high stiffness tend to flow easier under the effect of gravity.
More clear visualization of how \( \dot{\text{m}} \) is varying with respect to the parameters can be seen in Fig. 18, which shows an example of the mass and \( \dot{\text{m}} \) of six simulation cases plotted over time. The varied input parameters and the mean \( \dot{\text{m}} \) values of each run are presented in Table 4.
Factors affecting kinetic energy

Freeflowing
The overall translational kinetic energy (TKE) was recorded every 1 ms starting from the moment of particle insertion inside the funnel till the discharge of the last particle inside the catching container. The results showed that µ_{s,pp} has a negative impact on the TKE as illustrated in an example of three runs in Fig. 19.
From 0 to 1 s, the particles were inserted inside the funnel, and then there was 0.3 s settlement time for the particles before removing the stopper at 1.3 s. This resulted in having an almost identical character of variation of TKE from 0 to 1.3 s. The rapid increase in TKE within 0–0.1 s is explained by the falling (insertion) of the particles into the funnel. Within 0.1–1 s, the distance between the insertion region and the first contact of the particles in the vertical direction decreased as the funnel was being filled with particles. Then, as the particles were settling down, the TKE started decreasing. In the time between 1 and 1.3 s, a rapid decrease in the TKE was observed as no more particles are inserted and most of the particles are got in rest (settled down). It can be seen that upon removing the stopper, the peak of E_{kin}_7 was smaller than that of E_{kin}_5 and then E_{kin}_7 remained smaller and the total time for full discharge was longer compared to E_{kin}_5. The only difference between these two runs is the value of the µ_{s,pp} where it was 0.1 in run 5 and 0.85 in run 7. So, the high value of µ_{s,pp} decreases the overall TKE of the system.
On the other hand, E_{kin}_2 has a smaller e_{pp} than E_{kin}_5 which showed a minimal difference in a small interval of time during the discharge of the particles. Thus, e_{pp} has no significant influence on the overall TKE when µ_{s,pp} is low. On the contrary, e_{pp} has a significant influence on the overall TKE when µ_{s,pp} and µ_{r,pp} are both high as shown in Fig. 20.
Moreover, the particle size d_{S} has a major influence on the overall TKE. Figure 21 plots the overall TKE graphs of simulation cases 1 and 24 where the d_{S} in run 1 is 460 µm and the d_{S} in run 24 is 690 µm.
The graph plot shows that both runs have similar overall TKE during the insertion time. After removing the stopper, the overall TKE of run 1 with lower d_{S} (460 µm) is higher and reaches full discharge faster than run 24 with higher d_{S} (690 µm). This can be explained by that the number of particles decreases with the increase in radii keeping the same mass; therefore, the number of collisions decreases and thus leads to a decrease in the TKE.
For a better understanding of the relative level of effectivity of these parameters, the adjusted response graph and Pareto chart are also designed for this response. The adjusted R^{2} of the NATKE model of the freeflowing powder was 0.981. In Fig. 8d, the adjusted response graph for the NATKE is illustrated. The Pareto graph of effects on the NATKE of the freeflowing powder is shown in Fig. 22. It shows that the quadratic term of µ_{s,pp} has the highest positive effect and µ_{s,pp} has the highest negative effect on the NATKE, followed by µ_{r,pp}. This result harmonizes perfectly with the definitions of these two factors, as they represent, more or less, the extent of resistance of a particle to remain in its position upon being exposed to a certain force. Therefore, as they increase, the particles are more hindered, and therefore the TKE decreases. And since the particles in our system do not tend to move in the rotational direction as in the translational direction, the µ_{r,pp} is showing less effect than µ_{s,pp}.

Cohesive
The model fit of the NATKE of the cohesive powder was very good with an adjusted R^{2} = 0.97. The adjusted response graph for the NATKE is shown in Fig. 11d. The Pareto graph of effects on the NATKE (Fig. 23) shows that Y has the highest positive effect and µ_{s,pp} has the highest negative effect on the NATKE. As seen, a new factor, namely Y, compared to the freeflowing case, has been introduced as a significant parameter. The reason for that is the existence of the C_{pp} in the system representing an additional normal contact force tending to stick the particles more to each other. As Y denotes the stiffness of the particles, exerting an additional force on them along with less tendency to deform leads to some repulsion causing the higher velocity of the particles. This interactive effect of these two parameters can be seen also by the term C_{pp} * Y having a positive impact on the NATKE. On the contrary, maintaining the same value of Y with increasing the C_{pp}, decreases the NATKE, because the additional normal contact force ought to keep the particles in contact. It can be also observed that the particle size has a higher significant effect than in the freeflowing case. In fact, this can be justified by the increase in contact area along with the increase in normal contact force, the thing that would cause an increase in the frictional force in order to maintain a constant µ_{s,pp}.
In Fig. 24, the overall behavior of the TKE of the system in the cohesive case generally looks similar to the freeflowing case. Some phenomena discussed earlier regarding the effects of some parameters can be seen.
Factors affecting computation time

Freeflowing
The CT model of the freeflowing powder had a very high adjusted R^{2} value of 0.987. It is clearly shown in Table 3 how the CT is varying through the different simulation runs. The adjusted response graph for the CT is illustrated in Fig. 8e. In addition, Fig. 25 demonstrates the Pareto graph of effects on the CT of the freeflowing powder. It is indicated that Y has a big positive impact on CT, whereas d_{S} has a smaller negative effect on it. In other words, as the Y becomes bigger, the CT increases and as d_{S} increases, the CT decreases. Although e_{pp} has much less effect on CT compared to Y and d_{S}, yet it is important to notice that e_{pp} has a negative effect which might be used in another applications needing relatively high computation time.

Cohesive
The adjusted R^{2} of the CT model of the cohesive powder was very high as well (0.991). Figure 11e illustrates the adjusted response graph for the CT, and Fig. 26 presents the Pareto graph of effects on the CT of the cohesive powder. Similarly, the results showed that Y and d_{I} are the almost only two parameters affecting the CT as in the freeflowing study. In that, using a small Y and bigger d, via coarsegraining method, would save a lot of computational costs.
To add up, the count of particles for the freeflowing powder was 18,923, 32,700 and 63,864 when using particle size values of 690 µm, 575 µm and 460 µm, respectively, after applying CG. On the other side, the number of particles for the cohesive powder was 18,540, 30,604 and 55,877 when using particle size values of 694.2 µm, 587.4 µm and 480.6 µm, respectively.
Table 7 sums up the adjusted R^{2} values of the regression models of the five responses on the freeflowing and cohesive powders.
Prediction model and experimental validation
The main aim of this section is to validate the regression models of the parametric studies obtained above and to validate the numerical model based on experimental data. Therefore, the reference values of the AoR and ε determined from the experiments will be our targets in the following prediction simulations.
Freeflowing
Based on the results obtained, a prediction model was built to estimate the AoR and ε upon using an optimized combination between them. The predicted AoR and ε for the freeflowing powder are calculated according to Eqs. (22) and (23), respectively, as follows:
The constants in both equations are presented in Table 8.
As the value 0.61, which represents the experimental value of µ_{s,pp} of the freeflowing powder using the FT4 rheometer, is within the tested range of µ_{s,pp}, it was fixed in the prediction model. In addition, according to the obtained results, Y was set to minimum and d_{S} was set to maximum to reduce the CT. Using an integrated optimization feature algorithm in Cornerstone software, an optimized DEM parameter combination of µ_{r,pp} and e_{pp}, which aims to match our studied bulk responses (AoR and ε) with the experimental reference values with minimum deviation errors, is selected. Table 9 shows the combination of the DEM input parameters used in validating the prediction model and thus calibrating SpheroLac 100 (the freeflowing) with its experimental AoR and ε values. The values to be predicted were set as our experimental reference values.
The results in Table 9 validate the robustness of our regression model, and thus our powder was calibrated. On this occasion, Fig. 27 shows the numerical AoR of run 41 validated with the experimental AoR of the freeflowing powder.
Cohesive
Similarly, Eqs. (24) and (25) represent the prediction equations for the AoR and ε for the cohesive powder, respectively, as follows:
The constants of these latter equations are listed in Table 8 as well. To be stated, the prediction equations for both freeflowing and cohesive powders showed a nonlinear relation between the parameters, unlike the study conducted by Boikov [75]. He had no ambiguity in his sought responses as he assumed that the parameters are linearly dependent. It can be seen in this study that this depends on the application and not only on the type of powder being used.
The prediction model of the cohesive powder was validated by running a new simulation having µ_{s,pp} equal to the experimental value. Based on selecting the optimized parameter combination, Table 10 lists the results of the prediction run simulation of the AoR and ε compared and validated with the experimental data.
The very low deviation errors confirm the validity of our study approach, and thus InhaLac 251 (the cohesive powder) was calibrated as well. Moreover, Fig. 28 shows the AoR of run 54 compared with the experimental AoR of the cohesive powder.
Summary and conclusions
In the presented work, a semiautomated calibration approach was introduced in which two different powders, i.e., freeflowing and cohesive, were systematically studied and their parameters numerically calibrated using a DEM—experimental data and following regression analysis. The work aimed, firstly, to perform a systematic statistical parametric study to understand the impact of six interparticle DEM microscopic input parameters on four macroscopic bulk responses and on the computational time. Secondly, numerical validation of the experimental angle of repose and porosity values using a statistical prediction model was performed. The examined microscopic parameters were Young’s modulus, particle size, particle–particle coefficient of restitution, static and rolling friction coefficients and cohesion energy density. Interaction properties between particle and wall and between wall and wall were set constant, whereas particle–particle properties were extensively studied. Some of the highlights can be summarized as follows:

Applying powder characterization using measurement devices decreased the number of needed parameters to be calibrated, which improves the robustness of parameter tuning.

DoE proved to be an efficient tool in the calibration approach, whereas the regression analysis served in better understanding the impact of different DEM input parameters on the observed responses.

The quadratic Doptimal design model ascertained its efficiency and reliability in saving computational time by setting up a small optimized number of simulations to be run.

For the freeflowing study, it was shown that the static friction coefficient has the most significant impact on almost all the output responses. The particle size and stiffness, however, had the highest impact on the computation costs.

Regarding the cohesive study, the results were in many cases similar to those of the freeflowing study except that the particle stiffness had a negative impact on the angle of repose, and the cohesion energy density had some impact on all the responses. It has been proven in this study that the involvement of cohesion increases the influence of the particle stiffness on some responses, e.g., the angle of repose.

Scaling up the particle size using the coarsegraining method proved to have no effect on the angle of repose in both studies.

The built statistical prediction model yielded a good quantitative agreement between the DEM simulation and the experimental result values.
Based on these results, future work will focus on additional numerical and experimental studies under different conditions to determine the validation scope of the selected parameters. One application would be running auger dosing experiments and studying the mass flow rate. This would allow to validate the DEM model using a realscale machine, subjected to controlled initial and boundary conditions.
References
 1.
Parker RSR, Taylor P (1966) Adhesion and Adhesives. Pergamon Press, Oxford
 2.
Kapelle R, Schott D (2015) Calibration and verification experiments for discrete element modeling of cohesive materials. Procedia Eng 102:741–748
 3.
Cundall PA, Strack ODL (1979) A discrete numerical model for granular assemblies. Géotechnique 29:47–65. https://doi.org/10.1192/bjp.115.526.1065
 4.
Zhu HP, Zhou ZY, Yang RY, Yu AB (2007) Discrete particle simulation of particulate systems: theoretical developments. Chem Eng Sci 62:3378–3396. https://doi.org/10.1016/j.ces.2006.12.089
 5.
Tsunazawa Y, Shigeto Y, Tokoro C, Sakai M (2015) Numerical simulation of industrial die filling using the discrete element method. Chem Eng Sci 138:791–809. https://doi.org/10.1016/j.ces.2015.09.014
 6.
Markauskas D, Kačianauskas R (2006) Compacting of particles for biaxial compression test by the discrete element method. J Civ Eng Manag 12:153–161. https://doi.org/10.1080/13923730.2006.9636387
 7.
Marigo M, Cairns DL, Davies M et al (2010) Developing mechanistic understanding of granular behaviour in complex moving geometry using the Discrete Element Method Part B: investigation of flow and mixing in the Turbula^{®} mixer. Comput Model Eng Sci 59:217–238. https://doi.org/10.1016/j.powtec.2011.04.009
 8.
Matuttis HG, Luding S, Herrmann HJ (2000) Discrete element simulations of dense packings and heaps made of spherical and nonspherical particles. Powder Technol 109:278–292
 9.
Dutt M, Hancock B, Bentham C, Elliott J (2005) An implementation of granular dynamics for simulating frictional elastic particles based on the DL_POLY code. Comput Phys Commun 166:26–44. https://doi.org/10.1016/j.cpc.2004.10.006
 10.
Liu L, Kafui KD, Thornton C (2010) Impact breakage of spherical, cuboidal and cylindrical agglomerates. Powder Technol 199:189–196. https://doi.org/10.1016/j.powtec.2010.01.007
 11.
Hou QF, Dong KJ, Yu AB (2014) DEM study of the flow of cohesive particles in a screw feeder. Powder Technol 256:529–539. https://doi.org/10.1016/j.powtec.2014.01.062
 12.
Kretz D, CallauMonje S, Hitschler M et al (2016) Discrete element method (DEM) simulation and validation of a screw feeder system. Powder Technol 287:131–138. https://doi.org/10.1016/j.powtec.2015.09.038
 13.
Owen PJ, Cleary PW (2009) Prediction of screw conveyor performance using the Discrete Element Method (DEM). Powder Technol 193:274–288. https://doi.org/10.1016/j.powtec.2009.03.012
 14.
Obaid A, Turek S, Heider Y, Markert B (2017) A new monolithic Newtonmultigridbased FEM solution scheme for large strain dynamic poroelasticity problems. Int J Numer Meth Eng 109:1103–1129. https://doi.org/10.1002/nme.5315
 15.
Pillai U, Heider Y, Markert B (2018) A diffusive dynamic brittle fracture model for heterogeneous solids and porous materials with implementation using a userelement subroutine. Comput Mater Sci 153:36–47. https://doi.org/10.1016/j.commatsci.2018.06.024
 16.
Heider Y, Reiche S, Siebert P, Markert B (2018) Modeling of hydraulic fracturing using a porousmedia phasefield approach with reference to experimental data. Eng Fract Mech 202:116–134. https://doi.org/10.1016/j.engfracmech.2018.09.010
 17.
Prabhu B (2005) Microstructural and mechanical characterization of AlAl2O3 nanocomposites synthesized by highenergy milling. University of Central Florida
 18.
Marigo M, Cairns DL, Bowen J et al (2014) Relationship between single and bulk mechanical properties for zeolite ZSM5 spraydried particles. Particuology 14:130–138. https://doi.org/10.1016/j.partic.2013.05.006
 19.
Jones R (2003) From single particle AFM studies of adhesion and friction to bulk flow: forging the links. Granul Matter 4:191–204. https://doi.org/10.1007/s1003500201226
 20.
Roessler T, Richter C, Katterfeld A, Will F (2018) Development of a standard calibration procedure for the DEM parameters of cohesionless bulk materials—part I: solving the problem of ambiguous parameter combinations. Powder Technol 343:803–812. https://doi.org/10.1016/j.powtec.2018.11.034
 21.
Marigo M, Stitt EH (2015) Discrete element method (DEM) for industrial applications: comments on calibration and validation for the modelling of cylindrical pellets. KONA Powder Part J 32:236–252. https://doi.org/10.14356/kona.2015016
 22.
Alhashemi HMB, Alamoudi OSB (2018) A review on the angle of repose of granular materials. Powder Technol 330:397–417. https://doi.org/10.1016/j.powtec.2018.02.003
 23.
Coetzee CJ (2017) Review: calibration of the discrete element method. Powder Technol 310:104–142. https://doi.org/10.1016/j.powtec.2017.01.015
 24.
Liu SD, Zhou ZY, Zou RP et al (2014) Flow characteristics and discharge rate of ellipsoidal particles in a flat bottom hopper. Powder Technol 253:70–79. https://doi.org/10.1016/j.powtec.2013.11.001
 25.
Zhou YC, Xu BH, Yu B, Zulli P (2002) An experimental and numerical study of the angle of repose of coarse spheres. Powder Technol 125:45–54. https://doi.org/10.1109/MACE.2011.5986910
 26.
Yan Z, Wilkinson SK, Stitt EH, Marigo M (2015) Discrete element modelling (DEM) input parameters: understanding their impact on model predictions using statistical analysis. Comput Part Mech 2:283–299. https://doi.org/10.1007/s4057101500565
 27.
Lommen S, Schott D, Lodewijks G (2014) DEM speedup: stiffness effects on behavior of bulk material. Particuology 12:107–112. https://doi.org/10.1016/j.partic.2013.03.006
 28.
Boukouvala F, Gao Y, Muzzio F, Ierapetritou MG (2013) Reducedorder discrete element method modeling. Chem Eng Sci 95:12–26. https://doi.org/10.1016/j.ces.2013.01.053
 29.
El Kassem B, Brinz T, Heider Y, Markert B (2018) Experimental study and discrete element simulation of auger dosing of different pharmaceutical powders. Proc Appl Math Mech PAMM. https://doi.org/10.1002/pamm.201800261
 30.
Souihi N, Josefson M, Tajarobi P et al (2013) Design space estimation of the roller compaction process. Ind Eng Chem Res 52:12408–12419
 31.
Wilkinson SK, Turnbull SA, Yan Z et al (2017) A parametric evaluation of powder flowability using a Freeman rheometer through statistical and sensitivity analysis: a discrete element method (DEM) study. Comput Chem Eng 97:161–174. https://doi.org/10.1016/j.compchemeng.2016.11.034
 32.
Johnstone MW (2010) Calibration of DEM models for granular materials using bulk physical tests. PhD thesis. The University of Edinburgh
 33.
Benvenuti L, Kloss C, Pirker S (2016) Identification of DEM simulation parameters by Artificial Neural Networks and bulk experiments. 291:456–465. https://doi.org/10.1016/j.powtec.2016.01.003
 34.
Rackl M, Hanley KJ (2017) A methodical calibration procedure for discrete element models. Powder Technol 307:73–83. https://doi.org/10.1016/j.powtec.2016.11.048
 35.
Wei H, Tang X, Ge Y et al (2019) Numerical and experimental studies of the effect of iron ore particle shape on repose angle and porosity of a heap. Powder Technol 353:526–534. https://doi.org/10.1016/j.powtec.2019.05.031
 36.
Li T, Li C, Li C et al (2019) ScienceDirect Porosity of flowing rice layer: experiments and numerical simulation. Biosyst Eng 179:1–12. https://doi.org/10.1016/j.biosystemseng.2018.12.003
 37.
Cheng H, Shuku T, Thoeni K, Yamamoto H (2018) Probabilistic calibration of discrete element simulations using the sequential quasiMonte Carlo filter. Granul Matter 20:1–19. https://doi.org/10.1007/s100350170781y
 38.
Do HQ, Aragón AM, Schott DL (2017) Automated discrete element method calibration using genetic and optimization algorithms. In: EPJ Web of conferences, p 15011
 39.
Soltanbeigi B, Podlozhnyuk A, Papanicolopulos SA et al (2018) DEM study of mechanical characteristics of multispherical and superquadric particles at micro and macro scales. Powder Technol 329:288–303. https://doi.org/10.1016/j.powtec.2018.01.082
 40.
Labra C, Ooi JY, Sun J (2013) Spatial and temporal coarsegraining for DEM analysis. AIP Conf Proc 1542:1258–1261. https://doi.org/10.1063/1.4812167
 41.
Brini E, Algaer EA, Ganguly P et al (2013) Systematic coarsegraining methods for soft matter simulations—a review. Soft Matter 9:2108–2119. https://doi.org/10.1039/c2sm27201f
 42.
Bierwisch C, Kraft T, Riedel H, Moseler M (2009) Threedimensional discrete element models for the granular statics and dynamics of powders in cavity filling. J Mech Phys Solids 57:10–31. https://doi.org/10.1016/j.jmps.2008.10.006
 43.
Weinhart T, Labra C, Luding S, Ooi JY (2015) Influence of coarsegraining parameters on the analysis of DEM simulations of silo flow. Powder Technol 293:138–148. https://doi.org/10.1016/j.powtec.2015.11.052
 44.
Kloss C, Goniva C, Hager A et al (2012) Models, algorithms and validation for opensource DEM and CFDDEM. Prog Comput Fluid Dyn Int J 12:140. https://doi.org/10.1504/PCFD.2012.047457
 45.
Wensrich CM, Katterfeld A (2012) Rolling friction as a technique for modelling particle shape in DEM. Powder Technol 217:409–417. https://doi.org/10.1016/j.powtec.2011.10.057
 46.
Derakhshani SM, Schott DL, Lodewijks G (2015) Micro – macro properties of quartz sand: experimental investigation and DEM simulation. Powder Technol 269:127–138. https://doi.org/10.1016/j.powtec.2014.08.072
 47.
Zhou D, Qiu Y (2010) Understanding material properties in pharmaceutical product development and manufacturing: powder flow and mechanical properties. J Valid Technol 73:65–77. https://doi.org/10.6061/clinics/2018/e264
 48.
Beach LE (2011) Effect of dry particle coating on the properties of cohesive pharmaceutical powders. Eur J Pharm Sci 43(4):325–333
 49.
Krantz M, Zhang H, Zhu J (2009) Characterization of powder flow: static and dynamic testing. Powder Technol 194:239–245. https://doi.org/10.1016/j.powtec.2009.05.001
 50.
Emery E, Oliver J, Pugsley T et al (2009) Flowability of moist pharmaceutical powders. Powder Technol 189:409–415. https://doi.org/10.1016/j.powtec.2008.06.017
 51.
Lumay G, Boschini F, Traina K et al (2012) Measuring the flowing properties of powders and grains. Powder Technol 224:19–27. https://doi.org/10.1016/j.powtec.2012.02.015
 52.
Hertz H (1881) On contact between elastic bodies. J Reine Angew Math 171:156–171
 53.
Mindlin R (1949) Compliance of elastic bodies in contact. ASME Trans J Appl Mech 16:259–268
 54.
Vizcarra GC, Nimbalkar S, Casagrande M (2016) Modeling behaviour of railway ballast in prismoidal apparatus using discrete element method. Proc Eng 143:1177–1184. https://doi.org/10.1016/j.proeng.2016.06.125
 55.
Syed Z, Tekeste M, White D (2017) A coupled sliding and rolling friction model for DEM calibration. J Terramechanics 72:9–20. https://doi.org/10.1016/j.jterra.2017.03.003
 56.
Ai J, Chen JF, Rotter JM, Ooi JY (2011) Assessment of rolling resistance models in discrete element simulations. Powder Technol 206:269–282. https://doi.org/10.1016/j.powtec.2010.09.030
 57.
Iwashita K, Oda M (2000) Microdeformation mechanism of shear banding process based on modified distinct element method. Powder Technol 109:192–205. https://doi.org/10.1016/S00325910(99)002363
 58.
Johnson KL, Kendall K, Roberts AD (1971) Surface energy and the contact of elastic solids. Proc R Soc A Math Phys Eng Sci 324:301–313. https://doi.org/10.1098/rspa.1971.0141
 59.
Li Y, Xu Y, Thornton C (2005) A comparison of discrete element simulations and experiments for “sandpiles” composed of spherical particles. Powder Technol 160:219–228. https://doi.org/10.1016/j.powtec.2005.09.002
 60.
Boac JM, Casada ME, Maghirang RG, Harner JP (2010) Material and interaction properties of selected grains and oilseeds for modeling discrete particles. Trans ASABE 53:1201–1216. https://doi.org/10.13031/2013.32577
 61.
Li Z, Yang J, Xu X et al (2002) Particle shape characterization of fluidized catalytic cracking catalyst powders using the mean value and distribution of shape factors. Adv Powder Technol 13:249–263
 62.
Carr RL (1965) Evaluating flow properties of solids. Chem Eng 72:163–168
 63.
(2018) About the FT4 powder rheometer: shear testing. In: Free Technol https://www.freemantech.co.uk/powdertesting/ft4powderrheometerpowderflowtester/sheartesting. Accessed 26 Jan 2020
 64.
Worku ZA, Kumar D, Gomes JV et al (2017) Modelling and understanding powder flow properties and compactability of selected active pharmaceutical ingredients, excipients and physical mixtures from critical material properties. Int J Pharm 531:191–204. https://doi.org/10.1016/j.ijpharm.2017.08.063
 65.
Freeman R (2007) Measuring the flow properties of consolidated, conditioned and aerated powders—a comparative study using a powder rheometer and a rotational shear cell. Powder Technol 174:25–33. https://doi.org/10.1016/j.powtec.2006.10.016
 66.
(2018) Why are powders complex? The three phases of powder. In: Free. Technol. https://www.freemantech.co.uk/_powders/powderflowabilitybulkpropertiesofpowders. Accessed 16 Mar 2019
 67.
Sundararajan K (2018) Design of experiments—a primer. https://www.isixsigma.com/toolstemplates/designofexperimentsdoe/designexperiments␓primer/. Accessed 2 Apr 2019
 68.
Geuzaine C, Remacle JF (2017) A threedimensional finite element mesh generator with builtin pre and postprocessing facilities. Int J Numer Meth Engng 79:1309–1331. https://doi.org/10.1002/nme.2579
 69.
MakeItFrom (2019) EN 1.4404 (X2CrNiMo17122) Stainless Steel. https://www.makeitfrom.com/materialproperties/EN1.4404X2CrNiMo17122StainlessSteel. Accessed 19 Jan 2019
 70.
Roessler T, Katterfeld A (2018) Scaling of the angle of repose test and its influence on the calibration of DEM parameters using upscaled particles. Powder Technol 330:58–66. https://doi.org/10.1016/j.powtec.2018.01.044
 71.
Coetzee CJ (2016) Calibration of the discrete element method and the effect of particle shape. Powder Technol 297:50–70. https://doi.org/10.1016/j.powtec.2016.04.003
 72.
Briend R, Radziszewski P, Pasini D (2011) Virtual soil calibration for wheelsoil interaction simulations using the discreteelement method. Can Aeronaut Space J 57:59–64
 73.
Just S, Toschkoff G, Funke A et al (2013) Experimental analysis of tablet properties for discrete element modeling of an active coating process. AAPS PharmSciTech 14:402–411. https://doi.org/10.1208/s1224901399255
 74.
Combarros M, Feise HJ, Zetzener H, Kwade A (2014) Segregation of particulate solids: experiments and DEM simulations. Particuology 12:25–32. https://doi.org/10.1016/j.partic.2013.04.005
 75.
Boikov AV, Savelev R, Payor VA (2018) DEM calibration approach: design of experiment DEM calibration approach: design of experiment. J Phys Conf Ser. https://doi.org/10.1088/17426596/1015/3/032017
Acknowledgements
Open Access funding provided by Projekt DEAL.
Funding
This research did not receive any specific grant from funding agencies in the public, commercial, or notforprofit sectors.
Author information
Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
ElKassem, B., Salloum, N., Brinz, T. et al. A multivariate regression parametric study on DEM input parameters of freeflowing and cohesive powders with experimental databased validation. Comp. Part. Mech. 8, 87–111 (2021). https://doi.org/10.1007/s40571020003158
Received:
Revised:
Accepted:
Published:
Issue Date:
Keywords
 Discrete element method
 Freeflowing powder
 Cohesive powder
 Design of experiment
 Multivariate regression analysis
 Angle of repose