Advertisement

Mixed mode cohesive zone modelling and analysis of adhesively bonded composite T-joint under pull-out load

  • Atul U. Sane
  • Pramod M. Padole
  • C. M. Manjunatha
  • Rashmi V. Uddanwadiker
  • Pooja Jhunjhunwala
Technical Paper
  • 143 Downloads

Abstract

The failure behaviour of three different configurations of adhesively bonded carbon fibre composite T-joints subjected to pull-out load is investigated. Finite element analysis is carried out on the carbon fibre composite T-joint models. A non-linear, contact target-based cohesive zone model with appropriate traction separation law is selected to simulate the pull-out test condition in FE package ANSYS®. The FE analysis results are in close agreement with available experimental results.

Keywords

Carbon fibre composite T-joint FE analysis Cohesive zone modelling Adhesive bonding 

Notes

Acknowledgements

Authors wish to thank the support and encouragement provided by the Director, VNIT, The Head, Dept. of Mech. Engineering, VNIT, The Director, CSIR-NAL and The Head, STTD, CSIR-NAL.

References

  1. 1.
    Guo S, Morishima R (2011) Numerical analysis and experiment of composite sandwich T-joints subjected to pulling load. Compos Struct 94(1):229–238CrossRefGoogle Scholar
  2. 2.
    Bianchi F, Koh T, Zhang X, Partridge I, Mouritz A (2012) Finite element modelling of z-pinned composite T-joints. Compos Sci Technol 73:48–56CrossRefGoogle Scholar
  3. 3.
    Park Y-B, Lee B-H, Kweon J-H, Choi J-H, Choi I-H (2012) The strength of composite bonded T-joints transversely reinforced by carbon pins. Compos Struct 94(2):625–634CrossRefGoogle Scholar
  4. 4.
    Blake J, Shenoi R, House J, Turton T (2001) Progressive damage analysis of tee joints with viscoelastic inserts. Compos A Appl Sci Manuf 32(5):641–653CrossRefGoogle Scholar
  5. 5.
    Da Silva LF, Adams R (2002) The strength of adhesively bonded T-joints. Int J Adhes Adhes 22(4):311–315CrossRefGoogle Scholar
  6. 6.
    Khalili S, Ghaznavi A (2011) Numerical analysis of adhesively bonded T-joints with structural sandwiches and study of design parameters. Int J Adhes Adhes 31(5):347–356CrossRefGoogle Scholar
  7. 7.
    Koh T, Feih S, Mouritz A (2012) Strengthening mechanics of thin and thick composite T-joints reinforced with z-pins. Compos A Appl Sci Manuf 43(8):1308–1317CrossRefGoogle Scholar
  8. 8.
    Alfano M, Furgiuele F, Leonardi A, Maletta C, Paulino GH (2007) Cohesive zone modeling of mode I fracture in adhesive bonded joints. Key Eng Mater 348–349:13–16CrossRefzbMATHGoogle Scholar
  9. 9.
    Vijayaraju K, Mangalgiri P, Dattaguru B (2004) Experimental study of failure and failure progression in T-stiffened skins. Compos Struct 64(2):227–234CrossRefGoogle Scholar
  10. 10.
    ANSYS R (2013) 14.5. Academic, structural analysis guideGoogle Scholar
  11. 11.
    Sahoo P, Manjunatha C, Dattaguru B (2008) Failure prediction of adhesively bonded lap joints between metal and composite adherends, International Conference on Aerospace Science and Technology (INCAST-2008), IISc Bangalore, IndiaGoogle Scholar
  12. 12.
    Kumar S, Sridhar I, Sivashanker S, Osiyemi S (2006) Mode-I adhesive fracture energy measurement with modified single-lap joint test geometry. J Adhes Sci Technol 20(10):1109–1124CrossRefGoogle Scholar
  13. 13.
    Hexcel 319 adhesive data sheetGoogle Scholar

Copyright information

© The Brazilian Society of Mechanical Sciences and Engineering 2018

Authors and Affiliations

  • Atul U. Sane
    • 1
  • Pramod M. Padole
    • 1
  • C. M. Manjunatha
    • 2
  • Rashmi V. Uddanwadiker
    • 1
  • Pooja Jhunjhunwala
    • 1
  1. 1.Department of Mechanical EngineeringVisvesvaraya National Institute of TechnologyNagpurIndia
  2. 2.Fatigue and Structural Integrity Group, Structural Technologies DivisionCSIR-National Aerospace LaboratoriesBangaloreIndia

Personalised recommendations