Advertisement

Journal of Advanced Ceramics

, Volume 6, Issue 2, pp 120–128 | Cite as

Effect of texture microstructure on tribological properties of tailored Ti3AlC2 ceramic

  • Ludi Xu
  • Degui Zhu
  • Salvatore Grasso
  • Tohru S. Suzuki
  • Akira Kasahara
  • Masahiro Tosa
  • Byung-nam Kim
  • Yoshio Sakka
  • Minhao Zhu
  • Chunfeng Hu
Open Access
Research Article

Abstract

Tribological property of c-axis textured shell-like Ti3AlC2 ceramic was investigated using reciprocating sliding balls (SUS304) under loads of 1, 5, and 9 N. It was found that the textured top surface (TTS), corresponding to the (000l) plane, shows the lowest mean coefficient of friction in comparison with those measured on the textured side surface (TSS), where the sliding directions are parallel (TSS-1) and perpendicular (TSS-2) to c axis, under the same load. Among all the tested orientations, the TSS-2 exhibited the lowest wear rate of 1.51×10−3 mm3/(N·m) under the load of 9 N. The worn mechanisms on the TTS and TSS-1 were delamination, grain fracture, and grain spalling-off. On the TSS-2, plowing effect against balls was the dominating mechanism. This work suggests the criteria to maximize the wear resistance in the load range of 1–9 N.

Keywords

tailored Ti3AlC2 mean coefficient of friction wear rate worn mechanisms 

Notes

Acknowledgements

This work is supported by “ChuYing” Program of Southwest Jiaotong University and Thousand Talents Program of Sichuan Province. Also, we thank for the supports of National Natural Science Foundation of China (Nos. U1232136 and 91226202), Grant-in-Aid for Scientific Research B (No. 23350104) from Japan Society for the Promotion Science, the Fundamental Research Program of Korean Institute of Materials Science (KIMS), and UK EPSRC Material Systems for Extreme Environments Programme Grant (EP/K008749/1, XMat).

References

  1. [1]
    Barsoum M, El-Raghy T. The MAX phases: Unique new carbide and nitride materials. Am Sci 2001, 89: 334–343.CrossRefGoogle Scholar
  2. [2]
    Barsoum M, Radovic M. Mechanical properties of the MAX phases. Encyclopedia Mater: Sci Tech 2004: 1–16.Google Scholar
  3. [3]
    Wang XH, Zhou YC. Layered machinable and electrically conductive Ti2AlC and Ti3AlC2 ceramics: A review. J Mater Sci Technol 2010, 26: 385–416.CrossRefGoogle Scholar
  4. [4]
    Sun ZM. Progress in research and development on MAX phases: A family of layered ternary compounds. Int Mater Rev 2011, 56: 143–166.CrossRefGoogle Scholar
  5. [5]
    Eklund P, Beckers M, Jansson U, et al. The Mn+1AXn phases: Materials science and thin-film processing. Thin Solid Films 2010, 518: 1851–1878.CrossRefGoogle Scholar
  6. [6]
    Zhang J, Liu B, Wang JY, et al. Low-temperature instability of Ti2SnC: A combined transmission electron microscopy, differential scanning calorimetry, and X-ray diffraction investigations. J Mater Res 2009, 24: 39–49.CrossRefGoogle Scholar
  7. [7]
    Lin Z, Zhuo M, Zhou Y, et al. Microstructure and theoretical bulk modulus of layered ternary tantalum aluminum carbides. J Am Ceram Soc 2006, 89: 3765–3769.CrossRefGoogle Scholar
  8. [8]
    Zheng L, Wang J, Lu X, et al. (Ti0.5Nb0.5)5AlC4: A new-layered compound belonging to MAX phases. J Am Ceram Soc 2010, 93: 3068–3071.CrossRefGoogle Scholar
  9. [9]
    Hu C, Lai C-C, Tao Q, et al. Mo2Ga2C: A new ternary nanolaminated carbide. Chem Commun 2015, 51: 6560–6563.CrossRefGoogle Scholar
  10. [10]
    Wan D, Zhou Y, Hu C, et al. Improved strength-impairing contact damage resistance of Ti3Si(Al)C2/SiC composites. J Eur Ceram Soc 2007, 27: 2069–2076.CrossRefGoogle Scholar
  11. [11]
    Lee DB, Park SW. High-temperature oxidation of Ti3AlC2 between 1173 and 1473 K in air. Mat Sci Eng A 2006, 434: 147–154.CrossRefGoogle Scholar
  12. [12]
    Zhu J, Ye L, He L. Microstructure and mechanical properties of in situ synthesized Ti2AlC/Al2O3 composites. Mat Sci Eng A 2012, 547: 6–11.CrossRefGoogle Scholar
  13. [13]
    Duan X, Shen L, Jia D, et al. Synthesis of high-purity, isotropic or textured Cr2AlC bulk ceramics by spark plasma sintering of pressure-less sintered powders. J Eur Ceram Soc 2015, 35: 1393–1400.CrossRefGoogle Scholar
  14. [14]
    Heinzel A, Müller G, Weisenburger A. Compatibility of Ti3SiC2 with liquid Pb and PbBi containing oxygen. J Nucl Mater 2009, 392: 255–258.CrossRefGoogle Scholar
  15. [15]
    Tallman DJ, Hoffman EN, Caspi EN, et al. Effect of neutron irradiation on select MAX phases. Acta Mater 2015, 85: 132–143.CrossRefGoogle Scholar
  16. [16]
    Nappé JC, Monnet I, Grosseau P, et al. Structural changes induced by heavy ion irradiation in titanium silicon carbide. J Nucl Mater 2011, 409: 53–61.CrossRefGoogle Scholar
  17. [17]
    Gupta S, Filimonov D, Zaitsev V, et al. Ambient and 550 °C tribological behavior of select MAX phases against Ni-based superalloys. Wear 2008, 264: 270–278.CrossRefGoogle Scholar
  18. [18]
    Gupta S, Filimonov D, Palanisamy T, et al. Tribological behavior of select MAX phases against Al2O3 at elevated temperatures. Wear 2008, 265: 560–565.CrossRefGoogle Scholar
  19. [19]
    Ren S, Lu J, Jia Q, et al. Tribochemistry of Ti3SiC2/Si3N4 tribopair in ethanol. Tribol Int 2014, 74: 174–180.CrossRefGoogle Scholar
  20. [20]
    Ren S, Meng J, Wang J, et al. Tribo-corrosion behaviors of Ti3SiC2/Si3N4 tribo-pair in hydrochloric acid and sodium hydroxide solutions. Wear 2012, 274–275: 8–14.CrossRefGoogle Scholar
  21. [21]
    Zhu Y, Zhou A, Ji Y, et al. Tribological properties of Ti3SiC2 coupled with different counterfaces. Ceram Int 2015, 41: 6950–6955.CrossRefGoogle Scholar
  22. [22]
    Wan DT, Hu CF, Bao YW, et al. Effect of SiC particles on the friction and wear behavior of Ti3Si(Al)C2-based composites. Wear 2007, 262: 826–832.CrossRefGoogle Scholar
  23. [23]
    Hu C, Zhou Y, Bao Y, et al. Tribological properties of polycrystalline Ti3SiC2 and Al2O3-reinforced Ti3SiC2 composites. J Am Ceram Soc 2006, 89: 3456–3461.CrossRefGoogle Scholar
  24. [24]
    Hu C, Sakka Y, Tanaka H, et al. Fabrication of textured Nb4AlC3 ceramic by slip casting in a strong magnetic field and spark plasma sintering. J Am Ceram Soc 2011, 94: 410–415.CrossRefGoogle Scholar
  25. [25]
    Hu C, Sakka Y, Nishimura T, et al. Physical and mechanical properties of highly textured polycrystalline Nb4AlC3 ceramic. Sci Technol Adv Mat 2011, 12: 44603–44608.CrossRefGoogle Scholar
  26. [26]
    Hu C, Sakka Y, Grasso S, et al. Tailoring Ti3SiC2 ceramic via a strong magnetic field alignment method followed by spark plasma sintering. J Am Ceram Soc 2011, 94: 742–748.CrossRefGoogle Scholar
  27. [27]
    Zhang HB, Hu CF, Sato K, et al. Tailoring Ti3AlC2 ceramic with high anisotropic physical and mechanical properties. J Eur Ceram Soc 2015, 35: 393–397.CrossRefGoogle Scholar
  28. [28]
    Hu C, Sakka Y, Grasso S, et al. Shell-like nanolayered Nb4AlC3 ceramic with high strength and toughness. Scripta Mater 2011, 64: 765–768.CrossRefGoogle Scholar
  29. [29]
    Huang Z, Zhai H, Guan M, et al. Oxide-film-dependent tribological behaviors of Ti3SiC2. Wear 2007, 262: 1079–1085.CrossRefGoogle Scholar
  30. [30]
    Ma J, Hao J, Fu L, et al. Intrinsic self-lubricity of layered Ti3AlC2 under certain vacuum environment. Wear 2013, 297: 824–828.CrossRefGoogle Scholar
  31. [31]
    Zhou AG, Barsoum MW, Basu S, et al. Incipient and regular kink bands in fully dense and 10 vol.% porous Ti2AlC. Acta Mater 2006, 54: 1631–1639.CrossRefGoogle Scholar
  32. [32]
    Gupta S, Barsoum MW. On the tribology of the MAX phases and their composites during dry sliding: A review. Wear 2011, 271: 1878–1894.CrossRefGoogle Scholar
  33. [33]
    Barsoum MW, Zhen T, Kalidindi SR, et al. Fully reversible, dislocation-based compressive deformation of Ti3SiC2 to 1 GPa. Nat Mater 2003, 2: 107–111.CrossRefGoogle Scholar
  34. [34]
    Jones NG, Humphrey C, Connor LD, et al. On the relevance of kinking to reversible hysteresis in MAX phases. Acta Mater 2014, 69: 149–161.CrossRefGoogle Scholar
  35. [35]
    Wu L, Chen J, Liu M, et al. Reciprocating friction and wear behavior of Ti3AlC2 and Ti3AlC2/Al2O3 composites against AISI52100 bearing steel. Wear 2009, 266: 158–166.CrossRefGoogle Scholar
  36. [36]
    Lindquist M, Wilhelmsson O, Jansson U, et al. Tribofilm formation from TiC and nanocomposite TiAlC coatings, studied with focused ion beam and transmission electron microscopy. Wear 2009, 266: 988–994.CrossRefGoogle Scholar

Copyright information

© The Author(s) 2017

Open Access The articles published in this journal are distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Authors and Affiliations

  • Ludi Xu
    • 1
  • Degui Zhu
    • 1
  • Salvatore Grasso
    • 2
  • Tohru S. Suzuki
    • 3
  • Akira Kasahara
    • 3
  • Masahiro Tosa
    • 3
  • Byung-nam Kim
    • 3
  • Yoshio Sakka
    • 3
  • Minhao Zhu
    • 1
  • Chunfeng Hu
    • 1
  1. 1.Key Laboratory of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and EngineeringSouthwest Jiaotong UniversityChengduChina
  2. 2.School of Engineering and Material ScienceQueen Mary University of LondonLondonUK
  3. 3.National Institute for Materials ScienceTsukuba, IbarakiJapan

Personalised recommendations