Skip to main content
SpringerLink
Log in

Model Prediction and Experimental Study of Material Removal Rate in Micro ECDM Process on Borosilicate Glass

  • Original Paper
  • Published:
Silicon Aims and scope Submit manuscript

Abstract

Miniaturization of products has become a major technological challenge in production industries. Material removal in microscopic and sub-microscopic level has become a demand for producing such products. Electro-Chemical Discharge Machining (ECDM) is one of the hybrid non-conventional machining processes to machine materials that are electrically conductive and non-conductive at a micro-level utilizing the principles of Electro Discharge Machining (EDM) and Electro-Chemical Machining (ECM). The most common nonconductive materials machined with this process are various types of glasses, ceramics, composites, etc. In the current paper, a Finite Element Model (FEM) of the ECDM process is carried out in the discharge regime (less than 300 μm) with pulsed DC in a 2D domain to characterize the Material Removal Rate (MRR) as a process output response in borosilcate glass machining. From the model and experiements the value of MRR is found to be 0.373 mg/ min and 0.414 mg/min. It can be considered that there is almost negligible difference in MRR between experimental and model values with 9.9% error variation. Hence the results are validated with experimentation, and there is a good agreement observed between the results.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

Data Availability

The data is trnaparent and available for publisher to publish in journal

References

  1. Kulkarni A, Sharan R, Lal GK (2002) An experimental study of discharge mechanism in electrochemical discharge machining. Int J Mach Tool Manu 42:1121–1127

    Article  Google Scholar 

  2. Fascio V, Langen HH, Bleuler H, Comninellis C (2003) Investigations of the spark assisted chemical engraving. Electrochem Commun 5:203–207

    Article  CAS  Google Scholar 

  3. Ali B, Mohammad RR (2016) Experimental study of the tool Wear during the electrochemical discharge machining (ECDM). Mater Manuf Process 31:574–580

    Article  Google Scholar 

  4. Ali B, Mohammad RR (2016) Experimental and numerical study of material removal in electrochemical discharge machining (ECDM). Mater Manuf Process 31:495–503

    Article  Google Scholar 

  5. Basak I, Ghosh A (1996) Mechanism of spark generation during electrochemical discharge machining: a theoretical model and experimental verification. J Mater Process Technol 62:46–53

    Article  Google Scholar 

  6. Basak I, Ghosh A (1997) Mechanism of material removal in electrochemical discharge machining: a theoretical model and experimental verification. J Mater Process Technol 71:350–359

    Article  Google Scholar 

  7. Wang W, Liu ZD, Tian ZJ, Huang YH, Liu ZX (2009) High efficiency slicing of low resistance silicon ingot by wire electrolytic-spark hybrid machining. J Mater Process Technol 209:3149–3155

    Article  CAS  Google Scholar 

  8. Jui SK, Kamaraj AB, Sundaram MM (2013) High aspect ratio micromachining of glass by electrochemical discharge machining (ECDM). J Manuf Process 15:460–466

    Article  Google Scholar 

  9. Pankaj KG, Akshay D, Pradeep K (2015) Effect of pulse duration on quality characteristics of blind hole drilled in glass by ECDM. Mater Manuf Process 31:1740–1748

    Google Scholar 

  10. Jinka R, Somashekhar SH, Lijo P (2011) Parametric analysis and a soft computing approach on material removal rate in electrochemical discharge machining. Int J Manuf Technol Manag 24:23–39

    Article  Google Scholar 

  11. Roth HK, Wegener K (2013) Experimental investigation and simulation of heat flux into metallic surfaces due to single discharges in micro-electrochemical arc machining (micro-ECAM). Int J Adv Manuf Technol 68:1267–1275

    Article  Google Scholar 

  12. Lijo P, Somashekhar SH, Jinka R (2014) Experimental investigation and parametric analysis of electro chemical discharge machining. Int J Manuf Technol Manag 28:57–79

    Article  Google Scholar 

  13. Saranya S, Sankar AR (2018) Fabrication of precise micro-holes on quartz substrates with improved aspect ratio using the constant velocity feed drilling technique of an ECDM process. J Micromech Microeng 28(12):1–16

    Article  Google Scholar 

  14. Nasim S, Mansour H, Mohammad RR (2018) Experimental study on the heat-affected zone of glass substrate machined by electrochemical discharge machining (ECDM) process. Int J Adv Manuf Technol 1:1–8

    Google Scholar 

  15. Mudimallana G, Apurbba KS (2017) On performance studies during micromachining of quartz glass using electrochemical discharge machining. J Mech Sci Technol 31(3):1365–1372

    Article  Google Scholar 

  16. Tang W, Kang X, Zhao W (2019) Experimental investigation of gas evolution in electrochemical discharge machining process. Int J Electrochem Sci 14:970–984

    Article  CAS  Google Scholar 

  17. Gok A (2017) 2D numeric simulation of serrated-Chip formation in orthogonal cutting of AISI316H stainless steel. Mater Technol 51(6):953–956

    CAS  Google Scholar 

  18. Gok A (2015) A new approach to minimization of the surface roughness and cutting force via fuzzy TOPSIS multi-objective grey design and RSA. Measurement 70:100–109

    Article  Google Scholar 

  19. Gautam N, Jain VK (1997) Experimental investigations of ECSD process using various tool kinematics. Int J Mach Tool Manu 38:15–27

    Article  Google Scholar 

  20. Jain VK, Dixit PM, Pandey PM (1999) On the analysis of the electrochemical spark machining process. Int J Mach Tool Manu 39:165–186

    Article  Google Scholar 

  21. Bhondwe VY, Kathiresan G (2006) Finite element prediction of material removal rate due to electro-chemical spark machining. Int J Mach Tool Manu 46:1699–1706

    Article  Google Scholar 

  22. Panda MH, Yadava V (2009) Finite element prediction of material removal rate due to travelling wire electrochemical spark machining. Int J Adv Manuf Technol 45:506–520

    Article  Google Scholar 

  23. Jiang B, Lan S, Ni ZJ (2014) Experimental investigation of spark generation in electrochemical discharge machining of non-conducting materials. J Mater Process Technol 214:892–898

    Article  CAS  Google Scholar 

  24. Chenjun W, Kaizhou X, Jun N, Adam JB, Dejin H (2011) A finite element based model for electrochemical discharge machining in discharge regime. Int J Adv Manuf Technol 54:987–995

    Article  Google Scholar 

  25. Pravin P, Raj B, Amaresh K (2017) Micromachining of borosilicate glass: a state of art review. Mater Today: Proc 4:2813–2821

    Google Scholar 

  26. Arya RK, Dvivedi A (2019) Thermal loading effect during machining of borosilicate glass using ECDM process. IOP Conf Series: Mater Sci Eng 647

  27. Kumar S, Dvivedi A (2017) Experimental investigation on drilling of borosilicate glass using micro-USM with and without tool rotation: a comparative study. Int. J. AdditivSubtracte Mater Manufact 1:213–222

    Google Scholar 

  28. Ushasta A, Simul B, Asish B, Probal KD (2014) Abrasive water jet cutting of borosilicate glass. Procedia Mater Sci 6:775–785

    Article  Google Scholar 

  29. Lee HM, Choi JH, Moon SJ (2020) Machining characteristics of glass substrates containing chemical components in femtosecond laser helical drilling. Int J of Precis Eng and Manuf-Green Tech:1–11

  30. Wuthrich R (2009) Micromachining using electrochemical discharge phenomenon: fundamentals and application of spark assisted chemical engraving. Elsevier Oxford, UK

    Google Scholar 

  31. Lijo P, Somashekhar SH (2014) Evaluation of process parameters of ECDM using Grey relational analysis. Procedia Mater Sci 5:2273–2282

    Article  Google Scholar 

  32. Mochmaru Y, Ota M, Yamaguchi K (2012) Micro hole processing using electro-chemical discharge machining. J Adv Mechan Design, Syst Manufact 6:949–957

    Article  Google Scholar 

  33. Didar TF, Dolatabadi A, Wuthrich R (2008) Characterization and modeling of 2D-glass micro-machining by spark-assisted chemical engraving (SACE) with constant velocity. J Micromechan Micro Eng 18:1–10

    Google Scholar 

  34. Lijo P (2015) Characterization of micro features produced using μ-ECDM process: experimental and theoretical investigations. A dissertation submitted to IIT Madras, Chennai

    Google Scholar 

  35. Singh M, Singh S, Kumar S (2020) Experimental investigation for generation of micro-holes on silicon wafer using electrochemical discharge machining process. Silicon 12:1683–1689

    Article  CAS  Google Scholar 

  36. Yang CT, Ho SS, Yan BH (2001) Micro hole machining of borosilicate glass through electrochemical discharge machining (ECDM). Key Eng Mater 196:149–166

    Article  CAS  Google Scholar 

Download references

Acknowledgments

Not applicable

Financial Interests

The authors declare they have no financial interests.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, SJCET Palai, Kottayam, Kerala, 686579, India

    Lijo Paul

  2. Department of Mechanical Engineering, IIT Madras, Chennai, India

    Somashekhar S. Hiremath

Authors
  1. Lijo Paul
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Somashekhar S. Hiremath
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

All authors contributed to the study conception and design. Material preparation, data collection and analysis were performed by Dr. Lijo Paul and Dr. Somshekhar SH. The first draft of the manuscript was written by Dr. Lijo Paul and all authors commented on previous versions of the manuscript. All authors read and approved the final manuscript. Authors are responsible for correctness of the statements provided in the manuscript.

Corresponding author

Correspondence to Lijo Paul.

Ethics declarations

• The authors have no conflicts of interest

• No research involving Human Participants and/or Animals are conducted in current study

Conflicts of Interest/Competing Interests

The authors have no conflicts of interest to declare that are relevant to the content of this article.

Consent to Participate

Not applicable

Consent for Publication

The authors have no conflicts of interest for publication of content of this article.

• The authors have no relevant financial or non-financial interests to disclose.

• The authors have no conflicts of interest to declare that are relevant to the content of this article.

• All authors certify that they have no affiliations with or involvement in any organization or entity with any financial interest or non-financial interest in the subject matter or materials discussed in this manuscript.

• The authors have no financial or proprietary interests in any material discussed in this article.

• Authors are responsible for correctness of the statements provided in the manuscript.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Paul, L., Hiremath, S.S. Model Prediction and Experimental Study of Material Removal Rate in Micro ECDM Process on Borosilicate Glass. Silicon 14, 1497–1510 (2022). https://doi.org/10.1007/s12633-021-00948-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12633-021-00948-1

Keywords

Search

Navigation