Abstract
Increasing the bending and shear capacities of reinforced concrete members is an interesting issue in structural engineering. In recent years, many studies have been carried out to improve capacities of reinforced concrete members such as using post and pre-tensioning, Fiber Reinforced Polymer and other techniques. This paper proposes a novel and significant technique to increase the flexural capacity of simply supported reinforced concrete beams. The proposed method uses a new reinforcement bar system having bent-up bars, covered with rubber tubes. This technique will avoid interaction of bent-up bars with concrete. They are located in the zone where compressive and tensile forces act against one another. The compressive force in the upper point of the bent-up bars is exerted to the end point of these bars located under neutral axis. Moreover, the tensile stress is decreased in reinforcements located under the neutral axis. This will cause the Reinforced Concrete (RC) beam to endure extra loading before reaching yield stress. These factors may well be considered as reasons to increase bending capacity in the new system. The laboratory work together with finite element method analysis were carried out in this investigation. Furthermore, bending capacity, ductility, strength, and cracking zone were assessed for the new proposed system and compared with the conventional model. Both the FEM simulation and the experimental test results revealed that the proposed system has significant impact in increasing the load bearing capacity and the stiffness of the RC beams. In the present study, an equation is formulated to calculate bending capacity of a new reinforcement bar system beam.
Similar content being viewed by others
References
Figeys W, Verstrynge E, Brosens K, Van Schepdael L, Dereymaeker J, Van Gemert D, Schueremans L. Feasibility of a novel system to prestress externally bonded reinforcement. Materials and Structures, 2011, 44(9): 1655–1669
Kotynia R, Cholostiakow S. New proposal for flexural strengthening of reinforced concrete beams using CFRP T-shaped profiles. Polymers, 2015, 7(11): 2461–2477
Papanicolaou C G, Triantafillou T C, Papathanasiou M, Karlos K. Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: Out-of-plane cyclic loading. Materials and Structures, 2007, 41(1): 143–157
Pham T M, Hao H. Review of concrete structures strengthened with FRP against impact loading. Structures, 2016, 7: 59–70
Tanarslan H M. Flexural strengthening of RC beams with prefabricated ultra high performance fibre reinforced concrete laminates. Engineering Structures, 2017, 151: 337–348
Rasheed H A, Abdalla J, Hawileh R, Al-tamimi A K. Flexural behavior of reinforced concrete beams strengthened with externally bonded Aluminum Alloy plates. Engineering Structures, 2017, 147: 473–485
Wobbe E, Silva P, Barton B L, Dharani L R, Birman V, Nanni A, Alkhrdaji T, Thomas J, Tunis G. Flexural capacity of RC beams externally bonded with SRP and SRG. In: Proceedings of Society for the Advancement of material and Process Engineering 2004 Symposium, 2004, 16–20
Esfandiari M J, Rahimi Bondarabadi H, Sheikholarefin S, Dehghan Manshadi S H. Numerical investigation of parameters influencing debonding of FRP sheets in shear-strengthened beams. European Journal of Environmental and Civil Engineering, 2018, 22(2): 246–266
Oehlers D J. Reinforced concrete beams with plates glued to their soffits. Journal of Structural Engineering, 1992, 118(8): 2023–2038
Daly A F, Witarnawan W. Strengthening of bridges using external post-tensioning. In: International Conference of the Eastern Asia Society for Transportation Studies, 1997
Altun F. An experimental study of the jacketed reinforced-concrete beams under bending. Construction & Building Materials, 2004, 18(8): 611–618
Chaallal O, Nollet M J, Perraton D. Strengthening of reinforced concrete beams with externally bonded fiber-reinforced-plastic plates: design guidelines for shear and flexure. Canadian Journal of Civil Engineering, 1998, 25(4): 692–704
Smith S T, Teng J G. FRP-strengthened RC beams. I: Review of debonding strength models. Engineering Structures, 2002, 24(4): 385–395
Ross C A, Jerome D M, Tedesco J W, Hughes M L. Strengthening of reinforced concrete beams with externally bonded composite laminates. Structural Journal, 1999, 96(2): 212–220
Urgessa G S, Esfandiari M. Review of polymer coatings used for blast strengthening of reinforced concrete and masonry structures. In: International Congress on Polymers in Concrete (ICPIC 2018), 2018, 713–719
Lee H Y, Jung W T, Chung E. Flexural strengthening of reinforced concrete beams with pre-stressed near surface mounted CFRP systems. Composite Structures, 2017, 163: 1–12
Seraj S M, Kotsovos M D, Pavlović M N. Compressive-force path and behaviour of prestressed concrete beams. Materials and Structures, 1993, 26(2): 74–89
Shatarat N, Katkhuda H, Abdel-Jaber M, Alqam M. Experimental investigation of reinforced concrete beams with spiral reinforcement in shear. Construction & Building Materials, 2016, 125: 585–594
Yang K H, Kim G H, Yang H S. Shear behavior of continuous reinforced concrete T-beams using wire rope as internal shear reinforcement. Construction & Building Materials, 2011, 25(2): 911–918
Karayannis C G, Chalioris C E. Shear tests of reinforced concrete beams with continuous rectangular spiral reinforcement. Construction & Building Materials, 2013, 46: 86–97
Ghasemi M R, Shishegaran A. Role of slanted reinforcement on bending capacity SS beams. Vibroengineering PROCEDIA, 2017, 11: 195–199
Dassault Systems Simulia Corp. ABAQUS Analysis User’s Manual 6.10-EF, 2010
Rabczuk T, Zi G, Bordas S, Nguyen-Xuan H. A simple and robust three-dimensional cracking-particle method without enrichment. Computer Methods in Applied Mechanics and Engineering, 2010, 199(37–40): 2437–2455
Rabczuk T, Belytschko T. Cracking particles: A simplified mesh free method for arbitrary evolving cracks. International Journal for Numerical Methods in Engineering, 2004, 61(13): 2316–2343
Rabczuk T, Zi G, Bordas S, Nguyen-Xuan H. A geometrically nonlinear three dimensional cohesive crack method for reinforced concrete structures. Engineering Fracture Mechanics, 2008, 75(16): 4740–4758
Rabczuk T, Belytschko T. Application of particle methods to static fracture of reinforced concrete structures. International Journal of Fracture, 2006, 137(1–4): 19–49
Rabczuk T, Belytschko T. A three dimensional large deformation meshfree method for arbitrary evolving cracks. Computer Methods in Applied Mechanics and Engineering, 2007, 196(29–30): 2777–2799
Ghorashi S S, Valizadeh N, Mohammadi S, Rabczuk T. T-spline based XIGA for fracture analysis of orthotropic media. Computers & Structures, 2015, 147: 138–146
Amiri F, Anitescu C, Arroyo M, Bordas S P A, Rabczuk T. XLME interpolants, a seamless bridge between XFEM and enriched meshless methods. Computational Mechanics, 2014, 53(1): 45–57
Areias P, Msekh M A, Rabczuk T. Damage and fracture algorithm using the screened Poisson equation and local remeshing. Engineering Fracture Mechanics, 2016, 158: 116–143
Areias P, Rabczuk T. Steiner-point free edge cutting of tetrahedral meshes with applications in fracture. Finite Elements in Analysis and Design, 2017, 132: 27–41
Areias P, Reinoso J, Camanho P P, César de Sá J, Rabczuk T. Effective 2D and 3D crack propagation with local mesh refinement and the screened Poisson equation. Engineering Fracture Mechanics, 2018, 189: 339–360
Ren H, Zhuang X, Rabczuk T. Dual-horizon peridynamics: A stable solution to varying horizons. Computer Methods in Applied Mechanics and Engineering, 2017, 318: 762–782
Ren H, Zhuang X, Cai Y, Rabczuk T. Dual-horizon Peridynamics. International Journal for Numerical Methods in Engineering, 2016, 108(12): 1451–1476
Jankowiak T, Lodygowski T. Identification of parameters of concrete damage plasticity constitutive model. Foundations of Civil and Environmental Engineering, 2005, 6(1): 53–69
Vu-Bac N, Lahmer T, Zhuang X, Nguyen-Thoi T, Rabczuk T. A software framework for probabilistic sensitivity analysis for computationally expensive models. Advances in Engineering Software, 2016, 100: 19–31
Hamdia K M, Silani M, Zhuang X, He P, Rabczuk T. Stochastic analysis of the fracture toughness of polymeric nanoparticle composites using polynomial chaos expansions. International Journal of Fracture, 2017, 206(2): 215–227
Andersson S, Karlsson H. Structural response of reinforced concrete beams subjected to explosions, time dependent transformation factors, support reactions and distribution of section forces. Thesis for the Master’s Degree. Chalmers: Chalmers University of Technology, 2012, 6–110
FEA. Finite Element Analyses. Abaqus/CAE version 6.13: Computer Aided Engineering. Dassault Systemes, 2013
ASTM S. Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement. 615/A 615M-09b, 2009
ASTM C. Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars. C348-18, 2018
RCSC Committee. Specification for Structural Joints Using ASTM A325 or A490 Bolts. American Institute of Steel Construction (AISC), 2004
ASTM C. Standard Test Method for Flow of Hydraulic Cement Mortar. C1437, 2007
ASTM C. Standard test method for compressive strength of cylindrical concrete specimens. C39/C39M-12, 2012
Iribarren B S. Progressive collapse simulation of reinforced concrete structures: Influence of design and material parameters and investigation of the strain rate effects. Dissertation for the Doctoral Degree. Brussel: Université Libre de Bruxelles, 2011
Schlaich J, Schäfer K, Jennewein M. Toward a consistent design of structural concrete. PCI Journal, 1987, 32(3): 74–150
ACI Committee. Qualification of post-installed mechanical anchors in concrete and commentary. ACI Comm, ACI 355.2, 2004
ACI Committee. Code Requirements for nuclear safely related concrete structures. ACI Comm, ACI 349R-9, 1990
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Shishegaran, A., Ghasemi, M.R. & Varaee, H. Performance of a novel bent-up bars system not interacting with concrete. Front. Struct. Civ. Eng. 13, 1301–1315 (2019). https://doi.org/10.1007/s11709-019-0552-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11709-019-0552-4