Advertisement

Journal of Failure Analysis and Prevention

, Volume 17, Issue 3, pp 513–521 | Cite as

Prevention of Scum Formation and Entrapment in High Carbon Steel Billets

  • Murali Krishna Adepu
  • Preeti Prakash Sahoo
  • Bapin Kumar Rout
  • Shiv Kumar Choudhary
Technical Article---Peer-Reviewed

Abstract

Gradual build-up of scum over the liquid steel surface in the mould gives rise to entrapped exogenous inclusions and slag patch in the cast billets. The problem is more commonly observed during the open stream casting of continuous casting of high carbon (C > 0.6 mass%) steel billets. This problem has been quite commonly observed at Tata Steel during its billet casting. Present work aimed at eliminating the problem of scum formation during open stream billet casting of high carbon steel billets. This work involved experiments in the laboratory as well as in the plant. In addition, based on liquid steel composition thermodynamic calculations were carried out for predicting the possible oxide inclusions in Mn-Si deoxidised steels. Water model experiments were carried out in a full-scale billet caster physical model for investigating the influence of tundish outlet nozzle alignment on the entrapment of scum as slag patch over the billet surface. Based on these, cause of scum formation and its exact mechanism of entrapment in cast billets were established. Finally, countermeasures were recommended to the plant. Adequacy of the proposed countermeasures was established through a series of trials in the plant before implementation. Improvement obtained from the implementation over a period of time has been reported in the paper.

Keywords

High carbon steel Billets Open casting Scum formation Reoxidation Rhodonite Slag patch 

Notes

Acknowledgments

Authors are grateful to the management of Tata Steel Ltd. for providing permission to publish the work. Valuable help received from Mr. E. Z. Chacko, Mr. Manisankar Laru, Mr. G. Dinesh, Mr. Rajesh and Mr. Vikram Sharma is gratefully acknowledged.

References

  1. 1.
    J. Madias, A. Moreno, Strategies against reoxidation of liquid steel in billet casting with metering nozzle. in Proceedings of the Iron & Steel Technology Conference, Indianapolis, Indiana, USA, 5–8 May 2014, pp. 1771–1778Google Scholar
  2. 2.
    B. Thomas, The making, shaping and treating of the steel. in Fluid Flow in the Mold, 11th edn, vol. 5, Chapter 14. (AISE Steel Foundation, Pittsburg, PA, 2003), pp. 1–41Google Scholar
  3. 3.
    W.J. Maddever, A. McLean, J.S. Luckett, G.E. Forward, An investigation of casting streams. Can. Metall. Q. 12(1), 79–88 (1973)CrossRefGoogle Scholar
  4. 4.
    S.K. Choudhary, Influence of modified casting practice on steel cleanliness. ISIJ Int. 51(4), 557–565 (2011)CrossRefGoogle Scholar
  5. 5.
    L. Zhang, B.G. Thomas, inclusions in continuous casting of steel. in XXIV National Steelmaking Symposium, Morelia, Mich, Mexico, 26–28 Nov 2003, pp. 138–183Google Scholar
  6. 6.
    B. Santillana, M. Dziuba, J. Madias, M. Oropeza, E. Fernandez, Minimisation of slag entrapment and cold drops in sidetur billets. Ironmak. Steelmak. 30(6), 511–515 (2003)CrossRefGoogle Scholar
  7. 7.
    H. Mori, N. Tanaka, M. Hirai, Entrapped scum and pinholes in continuously-cast carbon steel billets. Tetsu-to-Hagane (J. Iron Steel Inst. Jpn.) 57, 1500–1513 (1971)CrossRefGoogle Scholar
  8. 8.
    S.K. Choudhary, S. Chandra, A. Ghosh, Prediction of deoxidation and inclusion precipitation in semikilled steel. Metall. Mater. Trans. B 36B, 59–66 (2005)CrossRefGoogle Scholar
  9. 9.
    Y.-B. Kang, H.-G. Lee, Inclusion chemistry for Mn/Si deoxidized steels: thermodynamic predictions and experimental confirmations. ISIJ 44(6), 1006–1015 (2004)CrossRefGoogle Scholar
  10. 10.
    S.K. Choudhary, S. Chandra, Castability of Mn-Si killed low carbon wire rod steel. ISIJ Int. 47(1), 190–192 (2007)CrossRefGoogle Scholar
  11. 11.
    A.D. Prasad, S.R. Sankaranarayanan, Thermodynamic modeling of deoxidation products and inclusion chemistry in Mn/Si killed tire-cord steel. J. Min. Metall. Sect. B: Metall. 48(1), 37–43 (2012)CrossRefGoogle Scholar

Copyright information

© ASM International 2017

Authors and Affiliations

  • Murali Krishna Adepu
    • 1
  • Preeti Prakash Sahoo
    • 1
  • Bapin Kumar Rout
    • 2
  • Shiv Kumar Choudhary
    • 1
  1. 1.Research and Development DivisionTata Steel LtdJamshedpurIndia
  2. 2.Swinburne University of TechnologyMelbourneAustralia

Personalised recommendations