Skip to main content
SpringerLink
Log in

Hydrogen Embrittlement Failure of a Galvanized Washer

  • Technical Article---Peer-Reviewed
  • Published:
Journal of Failure Analysis and Prevention Aims and scope Submit manuscript

Abstract

A galvanized washer used for a locomotive impeller broke into three pieces after an accumulative service of 4–5 h. The washer is fabricated from 42CrMo steel and the fracture surfaces reveal intergranular fracture morphology with microvoid coalescence observed on the facets. Microstructure observation indicates the presence of a severely banded microstructure mainly consisting of untempered martensite and bainite. The average hardness of the failed washer is HRC 59.1. The hardness value is much higher than specified (HBW 260-300) and is in the range of hydrogen embrittlement susceptibility. The significant number of elongated MnS inclusions acting as traps of hydrogen are present in the martensite regions. The delayed fracture associated with the predominance of intergranular fracture micromechanism and the high hardness level and the presence of microstructure susceptible for the hydrogen embrittlement strongly suggest the hydrogen embrittlement being the mostly possible failure mechanism. The likely sources for hydrogen entrapment are the electro-galvanizing process and acid-pickling before galvanizing. The hydrogen was retained in the washer due to absence of baking treatment to remove it or insufficient baking. The incorrect heat treatment process before galvanizing resulting in the high hardness level of the washer is mainly responsible for the occurrence of hydrogen embrittlement on the washer.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

References

  1. Fasteners-Electroplated Coatings. GB/T 5267.1-2002, China Standard, 2002 (in Chinese)

  2. A.K. Jha, P. Ramesh Narayanan, K. Sreekumar, M.C. Mittal, K.N. Ninan, Hydrogen embrittlement of 3.5Ni-1.5Cr-0.5 Mo steel fastener. Eng. Fail. Anal. 15, 431–439 (2008)

    Article  Google Scholar 

  3. Metals Handbook, Fractography and Atlas of Fractographs, 8th edn. vol. 9. (American Society for Metals, Metal Park, 1974)

  4. Steel-Determination of content of nonmetallic inclusions-Micrographic method using standards diagrams. GB/T 10561-2005, China Standard, 2005 (in Chinese)

  5. Villalba Ernesto, Andrej Atrens, Hydrogen embrittlement and rock bolt stress corrosion cracking. Eng. Fail. Anal. 16, 164–175 (2009)

    Article  Google Scholar 

  6. S. Raoul, B. Marini, A. Pineau, Effect of microstructure on the susceptibility of a 533 steel to temper embrittlement. J. Nucl. Mater. 357, 199–205 (1998)

    Article  Google Scholar 

  7. A.K. Jha, K. Sreekumar, Hydrogen-induced cracking (HIC) of hardened and tempered steel fastener used in space application. J. Fail. Anal. Prev. 9, 420–428 (2009)

    Article  Google Scholar 

  8. C.R.F. Azevedo, D. Magarotto, A.P. Tschiptschin, Embrittlement of case hardened steel chain link. Eng. Fail. Anal. 16, 2311–2317 (2009)

    Article  Google Scholar 

  9. J. Woodtli, R. Kieselbach, Damage due to hydrogen embrittlement and stress corrosion cracking. Eng. Fail. Anal. 7, 468–474 (2000)

    Article  Google Scholar 

  10. M.R. Louthan Jr, Hydrogen embrittlement of metals: a primer for the failure analyst. J. Fail. Anal. Prev. 8, 289–307 (2008)

    Article  Google Scholar 

  11. A.L. Marcelo, R.C. Tokumatsu, I. Ferreira, Hydrogen embrittlement in an AISI steel component of the sugarcane Industry. Eng. Fail. Anal. 16, 468–474 (2009)

    Article  Google Scholar 

  12. S.P. Lynch, D.P. Ewards, A. Crosky, Failure of a screw in a helicopter fuel-control unit: was it the cause of a fatal crash? J. Fail. Anal. Prev. 5, 39–49 (2004)

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Material Science and Engineering, Dalian Maritime University, Dalian, 116026, People’s Republic of China

    Xiao-lei Xu & Zhi-wei Yu

  2. College of Science, Northeast University, Shenyang, 110004, People’s Republic of China

    Haixuan Yu

Authors
  1. Xiao-lei Xu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Zhi-wei Yu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Haixuan Yu
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Xiao-lei Xu.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Xu, Xl., Yu, Zw. & Yu, H. Hydrogen Embrittlement Failure of a Galvanized Washer. J Fail. Anal. and Preven. 14, 197–202 (2014). https://doi.org/10.1007/s11668-014-9784-8

Download citation

  • Received:

  • Revised:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11668-014-9784-8

Keywords

Search

Navigation