Advertisement

Journal of Failure Analysis and Prevention

, Volume 12, Issue 1, pp 51–65 | Cite as

Modeling Erosion Wear Rates in Slurry Flotation Cells

  • M. G. Lipsett
  • V. Bhushan
Technical Article---Peer-Reviewed

Abstract

In processes using slurry as the working fluid, wear due to solid particles impinging on elements of the process units is a serious reliability issue. This study considers modeling wear damage in flotation cells, which are widely used in mineral processing. Flotation cells are typically cylindrical vessels where an impeller is used to agitate the fluid, enabling the liberation of the minerals from the slurry. Some solids, particularly those entrained in the impeller stream, can impact on the wall of the cell, leading to material loss and eventually to loss of structural integrity. The problem of predicting the remaining life of the unit due to erosion requires understanding of various sub-processes: flow modeling, particle–fluid interaction, energy interactions at the surface, and the mechanism of erosion itself. In this study, empirically developed equations for the flow field of cylindrical mixing vessel with a Rushton turbine are used in formulating a model relating and the damage accumulation rate to a simple set of measurable variables. To validate a model, a PIV technique was used to measure velocities in the flow field and near the wall on a physical model of the cell with transparent walls and particles that match the refractive index of the fluid. An Eulerian–Langrangian approach has been used to determine the particle trajectories and the effect of a squeeze film is incorporated into the model to modify the velocity distribution of particles prior to impacts. An analytical model based on equations of impulse and momentum for a particle of any shape striking a flat massive surface has been used to describe the energy lost at the walls. Finally, a damage model is developed that takes into account impact velocity, attack angle, properties of the impinging particles and the surface. This model is verified against a second physical model that measures material loss rate at different locations within the cell.

Keywords

Damage modeling Flotation cells Slurry Wear Particle–fluid interactions Particle image velocimetry 

Notes

Acknowledgments

Funding support is acknowledged from the Natural Sciences and Engineering Research Council, Syncrude Canada Ltd., and the University of Alberta.

References

  1. 1.
    Gillies, R.G., Shook, C.A.: Modeling high concentration settling slurry flows. Can. J. Chem. Eng. 78, 709–716 (2000)CrossRefGoogle Scholar
  2. 2.
    Gupta, R., Singh, S.N., Seshadri, V.: Study on the uneven wear rate in a slurry pipeline. Bulk Solids Handl. 15(4), 603–607 (1995)Google Scholar
  3. 3.
    Salama, M.M.: An alternative to API 14E erosional velocity limits for sand-laden fluids. J. Energy Resour. Technol. Trans. ASME 122(2), 71–77 (2000)CrossRefGoogle Scholar
  4. 4.
    Wood, R.J.K., Jones, T.F., Ganeshalingam, J., Miles, N.J.: Comparison of predicted and experimental erosion estimates in slurry ducts. Wear 256(9–10), 937–947 (2004)CrossRefGoogle Scholar
  5. 5.
    Schaan, J., Cook, N., Sanders, R.S.: On-line wear measurements for commercial-scale, coarse-particle slurry pipelines. In: 17th International Conference on the Hydraulic Transport of Solids. The South African Institute of Mining and Metallurgy and the BHR Group (2007)Google Scholar
  6. 6.
    Roco, M.C., Addie, G.R.: Erosion wear in slurry pumps and pipes. Powder Technol. 50, 35 (1987)CrossRefGoogle Scholar
  7. 7.
    Wilson, K.C., Addie, G.R., Sellgren, A., Clift, R.: Slurry transport using centrifugal pumps, 3rd edn. Springer, New York (2006)Google Scholar
  8. 8.
    Platzer, B., Noll, G.: Modelling of the local distributions of velocity components and turbulence parameters in agitated vessels—method and results. Chem. Eng. Process. 23, 13–31 (1988)CrossRefGoogle Scholar
  9. 9.
    Niu, Y.Y.: Evaluation of erosion in a two-way coupled fluid–particle system. Int. J. Numer. Methods Fluids 36(6), 711–742 (2001)CrossRefGoogle Scholar
  10. 10.
    Humphrey, J.A.C.: Fundamentals of fluid motion in erosion by solid particle impact. Int. J. Heat Fluid Flow 11(3), 170–195 (1990)CrossRefGoogle Scholar
  11. 11.
    Boothroyd, R.G.: Flowing Gas-Solids Suspensions. Chapman and Hall, London (1971)Google Scholar
  12. 12.
    Clark, H.M., Burmeister, L.C.: The influence of squeeze film on particle impact velocities in erosion. Int. J. Impact Eng. 12(3), 415–426 (1992)CrossRefGoogle Scholar
  13. 13.
    Brach, R.M.: Impact dynamics with applications to solid particle erosion. Int. J. Impact Eng. 7, 37–53 (1988)CrossRefGoogle Scholar
  14. 14.
    Sundararajan, G.: A comprehensive model for the solid particle erosion of ductile materials. Wear 149, 111–127 (1991)CrossRefGoogle Scholar
  15. 15.
    Finnie, I.: Erosion of surfaces by solid particles. Wear 3, 87 (1960)CrossRefGoogle Scholar
  16. 16.
    Bitter, J.P.A.: A study of erosion phenomena part I. Wear 6, 5 (1963)CrossRefGoogle Scholar
  17. 17.
    Bitter, J.P.A.: A study of erosion phenomena part II. Wear 6, 169 (1963)CrossRefGoogle Scholar
  18. 18.
    Meng, H.C., Ludema, K.C.: Wear models and predictive equations: their form and content 181–183, 443–457 (1995)Google Scholar
  19. 19.
    Oka, Y.I., Yoshida, T.: Practical estimation of erosion damage caused by solid particle impact. Part 2. Mechanical properties of material directly associated with erosion damage. Wear 259, 102–109 (2005)CrossRefGoogle Scholar
  20. 20.
    Oka, Y.I., Okamura, K., Yoshida, T.: Practical estimation of erosion damage caused by solid particle impact. Part 1: effects of impact parameters on a predictive equation. Wear 259, 95–101 (2005)CrossRefGoogle Scholar
  21. 21.
    Paul, E.L., Atiemo-Obeng, V.A., Kresta, S.M.: Handbook of Industrial Mixing. Wiley-Interscience, Hoboken (2004)Google Scholar
  22. 22.
    Wu, J., Nguyen, B., Graham, L., Zhu, Y., Kilpatrick, T., Davis, J.: Minimizing impeller slurry wear through multilayer paint modelling. Can. J. Chem. Eng. 83(5), 835–842 (2005)CrossRefGoogle Scholar

Copyright information

© ASM International 2011

Authors and Affiliations

  1. 1.Department of Mechanical EngineeringUniversity of AlbertaEdmontonCanada

Personalised recommendations