We describe the operating parameters of high-production-capacity container-glass melting furnaces and specify the service conditions of the melting-tank lining at a specific glass-melt production rate of 2.5 – 3.0 t/(m2·d) and a specific glass production per furnace run of 7000 – 8000 metric tons/m2. We recommend that melt-molded baddeleyite-corundum and vibration-cast sintered chromium-aluminum-zirconium refractories be used in tank structures.
Similar content being viewed by others
References
V. Ya. Dzyuzer, “Electrofused AZS refractories for high-capacity glass-founding furnaces,” Refract. Ind. Ceram., 54(4), 304 – 306 (2013).
L. M. Akselrod, et al., Refractory Service: AReference [in Russian], Intermet Inzhiniring, Moscow (2002), 656 pp.
O. N. Popov, P. T. Rybalkin, V. A. Sokolov, and S. D. Ivanov, Production and Use of Fused-Cast Refractories [in Russian], Metallurgiya, Moscow (1985), 256 pp..
Yu. A. Guloyan, O. M. Pustylnikov, and Yu. V. Raev, “Contact reactions between molten glass and refractories in glass melting furnaces,” Glass Russia, No. 5, 26 – 33 (2013).
V. B. Kogan, Theoretical Basis for Typical Processes in Chemical Technology [in Russian], Khimiya, Leningrad (1977), 592 pp.
C. Wagner, “The dissolution rate of sodium chloride with diffusion and natural convection as rate-determining factors,” J. Phys. Chem., No. 53, 1030 – 1033 (1949).
A. R. Cooper and W. D. Kingery, “Kinetics of solution in high viscosity liquids: Sodium chloride-glycerol,” J. Phys. Chem., No. 66, 665 – 668 (1962).
O. K. Botvinkin and T. B. Zhuze, “A study of glass formation at temperatures of 1400 – 1700°C,” Steklo Keram., No. 1, pp. 12 – 13 (1971).
V. Ya. Dzyuzer and V. S. Shvydkii, Design of Energy-Efficient Glass Melting Furnaces [in Russian], Teplotekhnik, Moscow (2009), 340 pp.
V. Ya. Dzyuzer, V. S. Shvydkii, and E. B. Sadykov, “Modeling the thermal operation of a high-capacity glass melting furnace,” Steklo Keram., No. 9, 23 – 27 (2012).
V. Ya. Dzyuzer and V. S. Shvydkii, “Boundary conditions for designing the lining of a glass-founding furnace with innovative parameters to improve technical efficiency,” Refract. Ind. Ceram., 56(6), 597 – 600 (2015).
T. S. Busby and J. Barker, “Simulative studies of upward drilling,” J. Am. Ceram. Soc., No. 49, 441 – 446 (1966).
J. Löffler, “Physikalische und chemische Reaktion, die in Glaswannen zur Ausbildung von Spülfugen oder zum Lochfraß führt,” Glastechn. Ber., 38(10), 398 – 405 (1965).
O. Citti, T. Champion, T. Azencot, et al., “High chrome refractories for severe wear areas in soda-lime glass melters,” Glass Worldwide, No. 51, 60 – 64 (2014).
M. Dietrich, and S. Postrach. “Chrome corundum: an alternative to isostatically pressed products,” RHI Bulletin, No. 2, 27 – 30 (2013).
Refractory Materials for the Glass Industry, Prospectus from RHI GLAS GmbH, available from http://www.rhi-ag.com.
Dzyuzer, V. Ya. “Basis for the development of the heat- insulating floor of a glassmaking furnace,” Refract. Ind. Ceram., 55(5), pp 444 – 447 (2014).
R. Brückner,, “Die zu Erosionen an Modellsubstanzen und feuerfesten Stoffen fuehrenden Grundmechanismen der Grenzflachenkonvektion,” Glastech. Ber., 40(12), 451 – 462 (1967).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Novye Ogneupory, No. 9, September, pp. 3 – 9 (2018).
Rights and permissions
About this article
Cite this article
Dzyuzer, V.Y. Use of Refractories in the Melting Tank of a High-Production-Capacity Glass Melting Furnace. Refract Ind Ceram 59, 435–440 (2019). https://doi.org/10.1007/s11148-019-00250-z
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11148-019-00250-z