Refractories and Industrial Ceramics

, Volume 54, Issue 2, pp 120–128 | Cite as

Preparation and Some Properties of Sintered Aluminosilicate Ceramic Based on HCBS. Part II1

  • Yu. E. Pivinskii
  • P. V. Dyakin
  • D. V. Gorbachev
  • S. A. Strel’tsov

Sintering and some properties of fine aluminosilicate ceramic, prepared on the basis of HCBS from broken porcelain electric insulator and pearlite, are studied. After firing at 1000 – 1500°C ceramic has open porosity of 1 – 8%, and ultimate strength in bending and compression of 45 – 65 and 350 – 500 MPa respectively. Compared with traditional fine ceramic materials, such as porcelain, semi-porcelain, hard faience, and majolica, in the new technology comparable properties are achieved with significantly (by a factor of 3 – 5) lower overall shrinkage and a reduced (by 150 – 200°C) firing temperature. Possible areas are indicated for implementingHCBS-technology in the field of production, not only for traditional fine ceramic, but also fine-grained structural, and artistic architectural ceramics.


HCBS casting sintering porosity shrinkage strength thermal expansion fine ceramics artistic architectural ceramics 


  1. 22.
    I. I. Moroz, T. S. Komskaya, and M. G. Sivchikova, Handbook for Porcelain and Faience Industry, Vol. 1 [in Russian], Legkaya Industriya, Moscow (1976).Google Scholar
  2. 23.
    I. A. Bulavin, A. I. Avgustinik, A. I. Zhukov, et al., Technology of Porcelain and Faience Manufacture [in Russian], Legkaya Industriya, Moscow (1975).Google Scholar
  3. 24.
    I. Yu. Guzman (editor), Chemical Technology of Ceramics [in Russian], OOO RIF Stroimaterialy, Moscow (2003).Google Scholar
  4. 25.
    I. Ya. Guzman, Chemical Technology of Fine Ceramics [in Russian], D. I. Mendeleev MKhTI, Moscow (1985).Google Scholar
  5. 26.
    P. A. Zemyatchenskii, USSR Clays. General Part [in Russian], Akad. Nauk SSSR, Moscow-Leningrad (1935).Google Scholar
  6. 27.
    I. Yu. Moreva, “Artificial ceramic binders based on activated materials in fine ceramic technology,” Author’s Abstr. Diss. Cand. Tech. Sci., Belgorod (2008).Google Scholar
  7. 28.
    E. I. Evtushenko, I. Yu. Moreva, V. A. Doroganov, et al., “Artificial ceramic binder suspensions based on silica-containing materials,” Stroit. Materialy, No. 8, 16 – 17 (2007).Google Scholar
  8. 29.
    E. I. Evtushenko, I. Yu. Moreva, V. I. Bedina, et al., “Porcelain and faience objects based on two-component binders,” Proc. II seminar-meeting, “Ceramics and refractories: potential solutions and technology,” V. G. Shukov BGTU, Belgorod (2009).Google Scholar
  9. 30.
    V. P. Barzakovskii and S. K. Dubrova, Physicochemical Properties of High-Voltage Porcelain Glazes [in Russian], Akad. Nauk SSSR, Moscow-Leningrad (1953).Google Scholar

Copyright information

© Springer Science+Business Media New York 2013

Authors and Affiliations

  • Yu. E. Pivinskii
    • 1
  • P. V. Dyakin
    • 2
  • D. V. Gorbachev
    • 3
  • S. A. Strel’tsov
    • 3
  1. 1.OOO NVF Kerambet-OgneuporSt. PetersburgRussia
  2. 2.GOU VPO St Petersburg State Technological Institute (Technical University)St. PetersburgRussia
  3. 3.OOO VKVS-TekhnologiiLipetskRussia

Personalised recommendations