Advertisement

Metal Science and Heat Treatment

, Volume 47, Issue 1–2, pp 30–35 | Cite as

Effect of Admixtures of Iron and Silicon on the Structure and Cracking of Near-Edge Volumes in Rolling of Large Flat Ingots from Alloy 7075

  • N. M. Doroshenko
  • B. V. Ovsyannikov
  • V. M. Zamyatin
  • V. I. Popov
Aluminum Alloys

Abstract

The effect of the content of iron and silicon admixtures in aluminum alloy 7075 on the composition, morphology, and fineness of phase components in the microstructure of ingots with cross section of 390 – 1330 mm in homogenized condition is studied. The mechanical properties of ingots at room and enhanced temperatures are determined depending on the content of iron and silicon in the alloy. The effect of the iron and silicon content in alloy 7075 on fracture of near-edge volumes in the process of hot rolling of plates with a thickness of 76.3 – 152 mm is determined.

Keywords

Iron Aluminum Silicon Microstructure Mechanical Property 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

REFERENCES

  1. 1.
    V. I. Dobatkin and V. I. Elagin, “Improvement of the combination of properties and quality of semiproducts from high-strength aluminum alloys,” Tekhnol. Legk. Splavov, No. 1, 3–9 (1976).Google Scholar
  2. 2.
    E. I. Kutaitseva, A. A. Petrova, V. V. Zakharov, et al., “A study of the structure and properties of semiproducts from alloy V95 with reduced content of iron and silicon impurities,” Tekhnol. Legk. Splavov, No. 5, 133 (1970).Google Scholar
  3. 3.
    V. V. Zakharov, A. A. Petrova, T. D. Rostova, et al., “Some ways for raising the ductility and fracture toughness of semiproducts from alloy V95pch,” Tekhnol. Legk. Splavov, No. 2, 7–11 (1980).Google Scholar
  4. 4.
    V. V. Teleshov, V. I. Kuzginov, and O. M. Sirotkina, “Special features of the structure and properties of edge volumes of plates from alloy V95pchT3 upon the development of porosity,” Tekhnol. Legk. Splavov, No. 5, 53–59 (1991).Google Scholar
  5. 5.
    V. P. Gusev, P. P. Petrun’kov, and I. P. Petrun’kova, “Defects of long-length plates from alloys V95pchT3, 1973T2 and their influence on altitudinal ductility,” Tekhnol. Legk. Splavov, Nos. 7–8, 30–36 (1993).Google Scholar
  6. 6.
    I. L. Teitel’, P. N. Silaev, and E. M. Nikitin, “Fabrication of defect-free pressed strips with cross section of 30 × 1000 mm from alloy V95,” Tekhnol. Legk. Splavov, No. 11, 15–19 (1975).Google Scholar
  7. 7.
    V. I. Kopnov, “A study of fracture conditions in rolling of large ingots from hard-to-deform aluminum alloys,” Tekhnol. Legk. Splavov, No. 1, 28–32 (1977).Google Scholar
  8. 8.
    M. B. Ovodenko, V. I. Kopnov, and F. V. Grechnikov, Rolling of Aluminum Alloys [in Russian], Metallurgiya, Moscow (1992).Google Scholar
  9. 9.
    Fracture Toughness of High-Strength Materials [Russian translation], Metallurgiya, Moscow (1973).Google Scholar
  10. 10.
    D. E. Piper, W. E. Quist, and W. E. Anderson, “The effect of composition on the fracture properties of aluminum alloys sheet,” in: AIME Symp., Philadelphia, Pa (1961), pp. 221–273.Google Scholar
  11. 11.
    L. F. Mondol’fo, Structure and Properties of Aluminum Alloys [Russian translation], Metallurgiya, Moscow (1979).Google Scholar
  12. 12.
    A. A. Alov, “Effect of the concentration of silicon and iron and of the Fe/Si ratio on hot brittleness of aluminum alloys,” Tekhnol. Legk. Splavov, No. 7, 11–15 (1978).Google Scholar

Copyright information

© Springer Science+Business Media, Inc. 2005

Authors and Affiliations

  • N. M. Doroshenko
    • 1
    • 2
  • B. V. Ovsyannikov
    • 1
    • 2
  • V. M. Zamyatin
    • 1
    • 2
  • V. I. Popov
    • 1
    • 2
  1. 1.Kamensk-Uralsky Metallurgical Works Joint-Stock CompanyKamensk-UralskyRussia
  2. 2.Ural State Technical University (UPI)EkaterinburgRussia

Personalised recommendations