Advertisement

Measurement Techniques

, Volume 56, Issue 11, pp 1257–1260 | Cite as

Determination of the Quality of an Internal Screw Thread in Treatment by Means of Plastic Deformation

  • V. A. Kosarev
  • N. D. Sugrobova
Linear and Angular Measurements

A method of control is considered, the manufacturing precision is estimated, and the quality of the filling of the profile of an internal screw thread produced by means of plastic deformation of metal is determined.

Keywords

internal screw thread plastic deformation profile filling 

References

  1. 1.
    V. A. Grecheshnikov, “Basic paths towards increasing the efficiency of tool technology,” Tekhnol. Mashinostr., No. 3, 26–29 (2010).Google Scholar
  2. 2.
    V. A. Grecheshnikov, Thread-Forming Tool: Handbook [in Russian], Izd. Tekhnol. Inst., Penza, Russia (1999).Google Scholar
  3. 3.
    S. N. Grigoriev et al., “The problems of metrological support for the preparation of production in machine construction,” Izmer. Tekhn., No. 5, 27–29 (2012); Measur. Techn., 55, No. 5, 526–529 (2012).Google Scholar
  4. 4.
    S. N. Grigoriev et al., “Control of parameters of the cutting process on the basis of diagnostics of the machine tool and workpiece,” Izmer. Tekhn., No. 5, 46–49 (2012); Measur. Techn., 55, No. 5, 555–558 (2012).Google Scholar
  5. 5.
    V. I. Teleshevskii, A. V. Glubokov, and S. V. Glubokova, “The automated choice of methods and instruments for measuring deviations of arrangement,” Izmer. Tekhn., No. 6, 30–34 (2012); Measur. Techn., 55, No. 6, 637–642 (2012).Google Scholar
  6. 6.
    S. N. Grigoriev et al., “Contemporary state and outlook for development of metrological assurance in the machinebuilding industry,” Izmer. Tekhn., No. 11, 56–60 (2012); Measur. Techn., 55, No.11, 1311–1315 (2012).Google Scholar
  7. 7.
    S. N. Grigoriev and V. I. Teleshevskii, “Measurement problems in technological shaping processes,” Izmer. Tekhn., No. 7, 3–8 (2011); Measur. Techn., 54, No.7, 744–749 (2011).Google Scholar
  8. 8.
    V. I. Teleshevskii, A. V. Shulepov, and O. Yu. Krasyuk, “Computerization of measuring microscopes with digital analysis of images,” Izmer. Tekhn., No. 8, 39–43 (2006); Measur. Techn., 49, No. 8, 797–802 (2006).Google Scholar
  9. 9.
    S. E. Ped and E. V. Darienko, “Error estimates in coordinate measurements of the cross section parameters of cylindrical surfaces,” Izmer. Tekhn., No. 8, 17–20 (2011); Measur. Techn., 54, No.8, 874–878 (2011).Google Scholar
  10. 10.
    GOST 9150–2002, Basic Norms of Interchangeability. Metric Thread. Profile.Google Scholar
  11. 11.
    GOST 24705–2004, Basic Norms of Interchangeability. Metric Thread. Basic Parameters.Google Scholar
  12. 12.
    GOST 8724–2002, Basic Norms of Interchangeability. Metric Thread. Diameters and Steps.Google Scholar

Copyright information

© Springer Science+Business Media New York 2014

Authors and Affiliations

  1. 1.STANKIN Moscow State Technological UniversityMoscowRussia

Personalised recommendations