The properties of briquettes of chopped aluminum wire after roller briquetting are determined. Increasing the relative cell depth by 50% reduces the compression ratio by 11% and the drop strength by 13%. The dependence of the compression ratio and the distribution of density and drop strength on the relative depth of the cell in the roll of the briquetting press is established for different cell configurations.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
G.-H. Zhang and K.-C. Chou, “Deoxidation of molten steel by aluminum,” J. Iron Steel Research Int., 22, No. 10, 905–908 (2015).
S. A. Botnikov, D. V. Morov, and G. V. Semernin, “Optimizing the production of steel with reduction by aluminum, in casting and rolling systems,” Steel Transl., 46, No. 2, 138–143 (2016).
G.-H. Zhang and K.-Ch. Chou, “Deoxidation of molten steel by aluminum,” J. Iron Steel Research Int., 22, No. 10, 905–908 (2015).
V. V. Parenchuk, N. P. Matsarenko, A. Ya. Babanin, and A. N. Khomchenko, “Resource-saving technology for deoxidizing steel by a powder wire made from fine aluminum chips,” Elektrometallurgiya, No. 5, 11–14 (2007).
J. Gronostajski, H. Marciniak, and A. Matuszak, “New methods of aluminium and aluminium-alloy chips recycling,” J. Mater. Proc. Technol., 106, No. 1–3, 34–39 (2000).
N. N. Zagirov, Yu. N. Loginov, and E. V. Ivanov, “Recycling copper-wire waste into long-length products by forming methods,” Vest. MGTU im. G. I. Nosova, 14, 50–55 (2016).
B. Wan, W. Chen, T. Lu, et al., “Review of solid state recycling of aluminum chips,” Resources, Conservation and Recycling, 125, 37–47 (2017).
N. N. Zagirov, S. B. Sidel’nikov, and R. E. Sokolov, “Comparative analysis of technologies for producing filler wire from eutectic silumin by combined processing methods,” Tsvetn. Metal., No. 4, 86–92 (2017).
V. E. Ibragimov and V. Yu. Bazhin, “Problem of producing environmentally dangerous solid waste during thermal recycling of aluminum alloys,” Innovats. Razvitie, No. 5 (10), 18–20 (2017).
V. Yu. Bazhin and L. M. Garsiya, “Problems of combined processing of aluminum waste,” in: Proc. 11th Int. Sci.-Appl. Conf. Sci. Res. Todays’ World (2016), pp. 23–25.
Yu. N. Loginov, L. I. Polyanskii, N. A. Babailov, and D. N. Pervukhina, “Briquetting as a method of controlling man-made mineral formations,” in: Proc. 4th Int. Interactive Sci.-Appl. Conf. Innovations Materials Technology Metallurgy, UrFU, Ekaterinburg (2015), pp. 229–233.
Yu. N. Loginov, S. P. Burkin, N. A. Babailov, and L. I. Polyanskii, Mechanics of Roll Briquettings of Loose Materials, AMB, Ekaterinburg (2011).
Y. N. Loginov, S. P. Bourkine, and N. A. Babailov, “Cinematics and volume deformations during roll-press briquetting,” J. Mater. Proc. Technology, 118, No. 1–3, 151–157 2001.
Yu. N. Loginov, N. A. Babailov, and S. P. Burkin, “Bulk deformation in roller briquetting of metallurgical waste,” Rus. Metallurgy (Metally), 1, 53–58 (2000).
Yu. N. Loginov, N. A. Babailov, and D. N. Pervukhina, “Physical modeling of roll pressing with asymmetric effect on the compressed material,” Izv. VUZov: Chern. Metallurg., 58, No. 3, 186–191 (2015).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Metallurg, Vol. 62, No. 8, pp. 5–8, August, 2018.
Rights and permissions
About this article
Cite this article
Babailov, N.A., Loginov, Y.N., Polyanskii, L.I. et al. Roll Briquetting for Recycling of Aluminum Wire. Metallurgist 62, 717–722 (2018). https://doi.org/10.1007/s11015-018-0713-z
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11015-018-0713-z