Abstract
Unidirectional carbon fiber–carbon matrix (CFC) composite tiles, which are proposed to be employed in thermal imaging diagnostic of powerful particle beams, have been designed, manufactured, and tested. The particle beam is intercepted by the tiles, which erodes the carbon surface producing debris, while a plasma forms in front of the tiles due to beam–gas interaction. Carbon fibers are aligned along the tile thickness to transfer the heat flux from the front to the rear surface with limited thermal pattern broadening thanks to the ten times higher thermal conductivity along the fibers. This feature of the tiles allows to detect thermal radiation at the tile rear surface by thermographic cameras, producing curves to be correlated to energy, intensity profile, and duration of the particle beam. Thermal patterns with spatial resolution of a few mm, time resolution up to 40 ms, and maximum temperature of 1300 °C have been measured on CFC tiles exposed to accelerated hydrogen beam pulses with power densities up to 13 MW m−2 in thehigh heat flux test facility GLADIS. Multiphysics transient non-linear parametric finite-element models have been developed to simulate thermal transfer inside tiles, thermal patterns at surfaces, and thermal deformations of tiles by varying spatial distribution and peak value of the power density. Temperature gradients, hoop deformations around the heated region, location of failure region, and failure time have been analysed and discussed to recognise the tile behaviour during the high heat flux tests. Simulation models have been validated by comparing outputs to experimental measurements. Finally, model geometry and parameters have been changed to simulate the behaviour of the complete diagnostic to be used in the Source for the Production of Ions of Deuterium Extracted from a Radio-frequency plasma (SPIDER) test bed of the ITER Neutral Beam Test Facility with expected power density up to 20 MW m−2.
Similar content being viewed by others
References
Toigo V, et al. The PRIMA test facility: SPIDER and MITICA test-beds for ITER neutral beam injectors. New J Phys. 2017;19:085004.
Toigo V, et al. The ITER Neutral Beam Test Facility towards SPIDER operation. Nucl Fusion. 2017;57:086027.
Ciric D, et al. Beam profiles measurement using a unidirectional CFC-target and infrared imaging. In: Proceedings of the 18th symposium on fusion technology, Karlsruhe, Germany, 22–26 August 1994.
Nocentini R, et al. Advanced ion beam calorimetry for the test facility ELISE. AIP Conf Proc. 2015;1655:060006. https://doi.org/10.1063/1.4916475.
De Muri M, et al. High energy flux thermo-mechanical test of 1D-carbon–carbon fibre composite prototypes for the SPIDER diagnostic calorimeter. Rev Sci Instrum. 2014;85(2):02A718.
Serianni G, et al. Neutralisation and transport of negative ion beams: physics and diagnostics. New J Phys. 2017;19:045003.
Pasqualotto R, et al. A suite of diagnostics to validate and optimize the prototype ITER neutral beam injector. J Instrum. 2017;12:C10009.
Toyo Tanso CO., LTD. CC-02037/Technical Data Sheet.
Greuner H, et al. High heat flux facility GLADIS: operational characteristics and results of W7-X pre-series target tests. J Nucl Mater. 2007;367–370 (Part B):1444–8.
Serianni G, et al. Test of 1D carbon–carbon composite prototype tiles for the SPIDER diagnostic calorimeter. AIP Conf Proc. 2017;1869:060007-7.
Hashin Z. Failure criteria for unidirectional fiber composites. J Appl Mech. 1980;47:329–34.
Love AEH. On the small free vibrations and deformations of elastic shells. Philos Trans R Soc (Lond). 1888;série A(17):491–549.
Reddy JN. Theory and analysis of elastic plates and shells. Boca Raton: CRC Press; 2007.
Zaldivar RJ, Rellick GS. Failure modes of unidirectional ultra-high-modulus carbon-fiber/carbon-matrix composite. The Aerospace Corporation El Segundo, CA 1998; SMC-TR-98-13; Aerospace Report No. TR-93(3935)-15.
Greuner H, et al. Experimental determination of the transient heat absorption of W divertor materials. Phys Scr. 2014;2014:0140035.
Acknowledgements
The work leading to this publication has been funded partially by Fusion for Energy. This publication reflects the views only of the authors, and F4E cannot be held responsible for any use which may be made of the information contained therein. The views and opinions expressed herein do not necessarily reflect those of the ITER Organization.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Dalla Palma, M., Gaule, D., Pimazzoni, A. et al. Thermal analysis and high heat flux testing of unidirectional carbon–carbon composite for infrared imaging diagnostic. J Therm Anal Calorim 134, 143–155 (2018). https://doi.org/10.1007/s10973-018-7430-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10973-018-7430-5