Abstract
Advancement in the field of construction has given rise to the modification of conventional materials in order to utilize the full potential of their components to achieve high durability, strength, and other engineering characteristics. Construction materials should ideally be environmental friendly. These diverse requirements resulted in the invention of high strength concrete (HSC). A rapidly increasing use of HSC in most of the construction projects has encouraged researchers to identify its behavior at elevated temperatures. This has led to the recognition of an inadequate understanding of elevated temperatures’ effects on the behavior of HSC. This paper initially provides necessary information about HSC and relates its benefits. A number of different design standards for the preparation of HSC are also presented and compared. Previous research activities performed on HSC to identify the effect of elevated temperatures on the properties of HSC are reviewed. Findings showed that the mechanical properties of NSC decreases at a 10% to 20% higher rate than HSC ranging between ambient temperature and approximately 350°C, depending upon the mix proportions and initial compressive strength of the concrete. The differences become narrower at temperature above 350°C. Major failure modes are identified and future recommendations are presented.
Similar content being viewed by others
References
Kodur V, Dwaikat M (2008) A numerical model for predicting the fire resistance of reinforced concrete beams. Cement Concr Compos 30(5):431–443
Gustaferro AH (1966) Factors influencing the fire resistance of concrete. Fire Technol 2(3):187–195
Schneider U (1988) Concrete at high temperatures—a general review. Fire Saf J 13(1):55–68
Forde MC (1993) High performance construction materials and systems: an essential program for America and its infrastructure technical report 93–5011. American Society of Civil Engineers, New York, ISBN 0-87262-938-2, 212 pp.
Russell HG (1999) ACI defines high-performance concrete. Concr Int 21:56–57
Bickley JA, Mitchell D (2001) A state-of-the-art review of high performance concrete structures built in Canada: 1990–2000. Cement Association of Canada, Ottawa
Cheng F-P, Kodur V, Wang T-C (2004) Stress-strain curves for high strength concrete at elevated temperatures. J Mater Civ Eng 16(1):84–90
Phan LT, Carino NJ (2003) Code provisions for high strength concrete strength-temperature relationship at elevated temperatures. Mater Struct 36(2):91–98
Kodur V, Mcgrath R (2003) Fire endurance of high strength concrete columns. Fire Technol 39(1):73–87
Basheer L, Kropp J, Cleland DJ (2001) Assessment of the durability of concrete from its permeation properties: a review. Constr Build Mater 15(2):93–103
Caldarone MA (2008) High-strength concrete: a practical guide. CRC Press, Cambridge
American Concrete Institute (ACI) Committee 363 (1992) State-of-the-art report on high-strength concrete. Report No. ACI 363R-92. Detroit, Michigan, US
European Committee for Standardization (1995) Eurocode 2: Design of concrete structures-Part 1-2: General rules-Structural fire design. ENV 1992-1-2.Brussels, Belgium
Standard Australia (AS5100) (2005) Australian Bridge Design Code, Section 5: Concrete
Noumowe A (2005) Mechanical properties and microstructure of high strength concrete containing polypropylene fibres exposed to temperatures up to 200°C. Cem Concr Res 35(11):2192–2198
Hameed AH (2009) The effect of curing condition on compressive strength in high strength concrete. Diyala J Eng Sci 2:35–48
Islam MN, Mohd Zain MF, Jamil M (2012) Prediction of strength and slump of rice husk ash incorporated high-performance concrete. J Civ Eng Manag 18(3):310–317
Usmani A, Chung Y, Torero JL (2003) How did the WTC towers collapse: a new theory. Fire Saf J 38(6):501–533
Anand N, Arulraj GP (2014) Effect of grade of concrete on the performance of self-compacting concrete beams subjected to elevated temperatures. Fire Technol 50(5):1269–1284
Diederichs U, Jumppanen U, Schneider U (1995) High temperature properties and spalling behaviour of high strength concrete. In: Proceedings of fourth Weimar workshop on high performance concrete. HAB Weimar, Germany, pp 219–235
Gibbons Jr AT (1971) Some aspects of structural fire endurance of concrete. Fire Technol 7(1):61–68
Kodur V (2014) Properties of concrete at elevated temperatures. ISRN Civil Engineering 2014
Kodur V, Raut N (2010) Performance of concrete structures under fire hazard: emerging trends. Indian Concr J 84(2):23–31
Malhotra H (1956) The effect of temperature on the compressive strength of concrete. Mag Concr Res 8(23):85–94
Harada T, Takeda J, Yamane S, Furumura F (1972) Strength, elasticity and thermal properties of concrete subjected to elevated temperatures. Spec Publ 34:377–406
Arioz O (2007) Effects of elevated temperatures on properties of concrete. Fire Saf J 42(8):516–522
Netinger I, Kesegic I, Guljas I (2011) The effect of high temperatures on the mechanical properties of concrete made with different types of aggregates. Fire Saf J 46 (7):425–430
Katz A, Berman N, Bank LC (1999) Effect of high temperature on bond strength of FRP rebars. J Compos Constr 3(2):73–81
Aköz F, Yüzer N, Koral S (1995) The influence of high temperature on the physical and mechanical properties of ordinary Portland cement and silica fume mortar. Teknik Dergi-Tmmob Insaat Muhendisleri Odasi 6:287–292
Husem M (2006) The effects of high temperature on compressive and flexural strengths of ordinary and high-performance concrete. Fire Saf J 41(2):155–163
Aydın S, Yazıcı H, Baradan B (2008) High temperature resistance of normal strength and autoclaved high strength mortars incorporated polypropylene and steel fibers. Constr Build Mater 22(4):504–512
Malhotra V, Wilson H, Painter K (1989) Performance of gravelstone concrete incorporating silica fume at elevated temperatures. Spec Publ 114:1051–1076
Noumowe A, Clastres P, Debicki G, Costaz J (1995) High performance concrete for severe thermal conditions. In: Proceedings of the international conference on concrete under severe conditions, CONSEC, pp 1129–1140
Phan LT, Carino NJ (1998) Review of mechanical properties of HSC at elevated temperature. J Mater Civ Eng 10(1):58–65
Chan SY, Peng G-f, Chan JK (1996) Comparison between high strength concrete and normal strength concrete subjected to high temperature. Mater Struct 29(10):616–619
Dwaikat M, Kodur V (2010) Fire induced spalling in high strength concrete beams. Fire Technol 46(1):251–274
Iwankiw N (2007) Fire resistant design. Pract Period Struct Des Constr 12(1):3–8
Mehta PK (1986) Concrete. Structure, properties and materials. Prentice-Hall Publication, New Delhi
Aïtcin P-C, Mehta PK (1990) Effect of coarse aggregate characteristics on mechanical properties of high-strength concrete. Mater J 87(2):103–107
de Larrard F, Belloc A (1997) The influence of aggregate on the compressive strength of normal and high-strength concrete. ACI Mater J 94(5):417–426
Yan H, Sun W, Chen H (1999) The effect of silica fume and steel fiber on the dynamic mechanical performance of high-strength concrete. Cem Concr Res 29(3):423–426
Gopalan MK, Haque M (1990) Fly ash in high-strength concrete. Spec Publ 121:331–350
Chan Y, Peng G, Anson M (1999) Residual strength and pore structure of high-strength concrete and normal strength concrete after exposure to high temperatures. Cem Concr Compos 21(1):23–27
Wu W, Zhang W, Ma G (2010) Optimum content of copper slag as a fine aggregate in high strength concrete. Mater Des 31(6):2878–2883
Jianyong L, Pei T (1997) Effect of slag and silica fume on mechanical properties of high strength concrete. Cem Concr Res 27(6):833–837
Aıtcin P (2003) The durability characteristics of high performance concrete: a review. Cement Concr Compos 25(4):409–420
Burg RG, Ost BW (1994) Engineering properties of commercially available high-strength concretes (including three year data), PCA Research and Development Bulletin RD104T. Portland Cement Association, Skokie
Kodur VKR, Sultan MA (1998) Structural behaviour of high strength concrete columns exposed to fire. In: Proceedings of the international symposium on high performance and reactive powder concrete, vol 4. Sherbrooke, Quebec, Canada, pp 217–32
Phan LT (1996) Fire performance of high-strength concrete: A report of the state-of-the art. US Department of Commerce, Technology Administration, National Institute of Standards and Technology, Office of Applied Economics, Building and Fire Research Laboratory
Jahren P (1989) Fire resistance of high strength/dense concrete with particular reference to the use of condensed silica fume—a review. Spec Publ 114:1013–1050
Castillo C (1987) Effect of transient high temperature on high-strength concrete. Doctoral dissertation, Rice University, Texas, US
Lea F (1920) The effect of temperature on some of the properties of materials. Engineering 110(2852):293
Lea F (1922) The resistance to fire of concrete and reinforced concrete. J Soc Chem Ind 41(18):395R–396R
Franssen J-M, Dotreppe J-C (2003) Fire tests and calculation methods for circular concrete columns. Fire Technol 39(1):89–97
Saemann J, Washa G (1957) Variation of mortar and concrete properties with temperature. J Am Concr Inst 29(5):385–395
Zoldners N (1960) Effect of high temperatures on concretes incorporating different aggregates. Department of Mines and Technical Surveys, Mines Branch, Ottawa
Hannant D (1964) Effects of heat on concrete strength. Engineering (London) 203(21):302
Abrams MS (1971) Compressive strength of concrete at temperatures to 1600F. Spec Publ 25:33–58
Lankard DR, Birkimer DL, Fondriest FF, Snyder MJ (1971) Effects of moisture content on the structural properties of portland cement concrete exposed to temperatures up to 500F. Spec Publ 25:59–102
Schneider U (1976) Behaviour of concrete under thermal steady state and non-steady state conditions. Fire Mater 1(3):103–115
Zoldners NG (1971) Thermal properties of concrete under sustained elevated temperatures. Spec Publ 25:1–32
Lie T, Kodur V (1996) Thermal and mechanical properties of steel-fibre-reinforced concrete at elevated temperatures. Can J Civ Eng 23(2):511–517
Poon C-S, Azhar S, Anson M, Wong Y-L (2003) Performance of metakaolin concrete at elevated temperatures. Cem Concr Compos 25(1):83–89
Shin K-Y, Kim S-B, Kim J-H, Chung M, Jung P-S (2002) Thermo-physical properties and transient heat transfer of concrete at elevated temperatures. Nucl Eng Des 212(1):233–241
Khaliq W, Kodur V (2011) Thermal and mechanical properties of fiber reinforced high performance self-consolidating concrete at elevated temperatures. Cem Concr Res 41(11):1112–1122
Diederichs U, Jumppanen U, Penttala V (1988) Material properties of high strength concrete at elevated temperatures. In: Proceedings of 13th congress of IABSE. Zurich, pp 489-494.
Morita T, Saito H, Kumagai H (1992) Residual mechanical properties of high strength concrete members exposed to high temperature-Part 1: Test on material properties. In: Summaries of technical papers of annual meeting, architectural institute of Japan, Niigata
Sullivan P, Sharshar R (1992) The performance of concrete at elevated temperatures (as measured by the reduction in compressive strength). Fire Technol 28(3):240–250
Furumura F, Ave T, Shinohara Y, Abe T (1995) Mechanical properties of high strength concrete at high temperatures. In: Proceedings of the fourth Weimar workshop on high performance concrete, pp 237–252
Noumowe A, Clastres P, Debicki G, Costaz J (1996) Thermal stresses and water vapor pressure of high performance concrete at high temperature. In: Proceedings, 4th international symposium on utilization of high-strength/high-performance concrete, Paris, France
Hertz K (1984) Heat induced explosion of dense concretes. Report 166. CIB W14/84/33 (DK). Institute of Building Design (now Department of Civil Engineering), Technical University of Denmark
Hertz KD (1992) Danish investigations on silica fume concretes at elevated temperatures. Mater J 89(4):345–347
Sanjayan G, Stocks L (1993) Spalling of high-strength silica fume concrete in fire. Mater J 90(2):170–173
Sarshar R, Khoury G (1993) Material and environmental factors influencing the compressive strength of unsealed cement paste and concrete at high temperatures. Mag Concr Res 45(162):51–61
Hammer T (1995) High-strength concrete phase, compressive strength and E-modulus at elevated temperatures (SP6 fire resistance, report 6.1). SINTEF Structures and Concrete
Felicetti R, Gambarova PG (1998) Effects of high temperature on the residual compressive strength of high-strength siliceous concretes. ACI Mater J 95:395–406
Balendran R, Nadeem A, Maqsood T, Leung H (2003) Flexural and split cylinder strengths of HSC at elevated temperatures. Fire Technol 39(1):47–61
Chan Y, Luo X, Sun W (2000) Compressive strength and pore structure of high-performance concrete after exposure to high temperature up to 800°C. Cem Concr Res 30(2):247–251
Hsu LS, Hsu CT (1994) Stress-strain behavior of steel-fiber high-strength concrete under compression. Struct J 91(4):448–457
Khoury G (1992) Compressive strength of concrete at high temperatures: a reassessment. Mag Concr Res 44(161):291–309
Noumowe AN, Siddique R, Debicki G (2009) Permeability of high-performance concrete subjected to elevated temperature (600°C). Constr Build Mater 23(5):1855–1861
Poon C-S, Azhar S, Anson M, Wong Y-L (2001) Comparison of the strength and durability performance of normal-and high-strength pozzolanic concretes at elevated temperatures. Cem Concr Res 31(9):1291–1300
ASTM (1990) E119-88: Standard methods of fire test of building construction and materials. American Society for Testing and Materials, Philadelphia
CAN/ULC-S101-M89 (1989) Standard Methods of Fire Endurance Tests of Building Construction and Materials. Underwriters’ Laboratories of Canada, Scarborough, Canada
Kodur V, Cheng F-P, Wang T-C, Sultan M (2003) Effect of strength and fiber reinforcement on fire resistance of high-strength concrete columns. J Struct Eng 129(2):253–259
Finland CAo (1991) High strength concrete supplementary rules and fire design. RakMKB4
Hernández-Olivares F, Barluenga G (2004) Fire performance of recycled rubber-filled high-strength concrete. Cem Concr Res 34(1):109–117
Xiao J, Xie Q, Li Z, Wang W (2017) Fire resistance and post-fire seismic behavior of high strength concrete shear walls. Fire Technol 53(1):65–86
Gales J, Parker T, Cree D, Green M (2016) Fire performance of sustainable recycled concrete aggregates: mechanical properties at elevated temperatures and current research needs. Fire Technol 52(3):817–845
Li M, Qian C, Sun W (2004) Mechanical properties of high-strength concrete after fire. Cem Concr Res 34(6):1001–1005
Behnood A, Ghandehari M (2009) Comparison of compressive and splitting tensile strength of high-strength concrete with and without polypropylene fibers heated to high temperatures. Fire Saf J 44(8):1015–1022
Aslani F, Samali B (2014) High strength polypropylene fibre reinforcement concrete at high temperature. Fire Technol 50(5):1229–1247
Min L, Xiang QC, Wei S (2004) Mechanical properties of high-strength concrete after fire. Cem Concr Res 34(6):1001–1005
Xiong Y, Deng S, Wu D (2016) Experimental study on compressive strength recovery effect of fire-damaged high strength concrete after realkalisation treatment. Procedia Eng 135:475–480
Nazari A, Riahi S (2011) The effects of SiO 2 nanoparticles on physical and mechanical properties of high strength compacting concrete. Compos Part B Eng 42(3):570–578
Lie T (1992) Structural fire protection: manual of practice. ASCE Manuals and Reports of Engineering Practice
Malhotra HL (1982) Design of fire-resisting structures. Surrey University Press, Guildford
Purkiss JA, Li L-Y (2013) Fire safety engineering design of structures. CRC Press, Cambridge
Anderberg Y, Thelandersson S (1976) Stress and deformation characteristics of concrete at high temperatures. 2. Experimental investigation and material behaviour model. Bull Div Struct Mech Concr Constr Bull 54:1–84
Xiao J, König G (2004) Study on concrete at high temperature in China—an overview. Fire Saf J 39(1):89–103
Khennane A, Baker G (1993) Uniaxial model for concrete under variable temperature and stress. J Eng Mech 119(8):1507–1525
Purkiss J, Dougill J (1973) Apparatus for compression tests on concrete at high temperatures. Mag Concr Res 25(83):102–108
Terro MJ (1998) Numerical modeling of the behavior of concrete structures in fire. ACI Struct J 95(2):183–193
Schneider U (1986) Modelling of concrete behaviour at high temperatures. In: Anchor RO et al. (eds.), Design of structures against fire. Elsevier, London, pp 53–69
Bazant ZP, Chern J-C (1987) Stress-induced thermal and shrinkage strains in concrete. J Eng Mech 113(10):1493–1511
Li L-y, Purkiss J (2005) Stress–strain constitutive equations of concrete material at elevated temperatures. Fire Saf J 40(7):669–686
Carreira DJ, Chu K-H (1985) Stress-strain relationship for plain concrete in compression. J Proc 6:797–804
Chin M, Mansur M, Wee T (1997) Effects of shape, size, and casting direction of specimens on stress-strain curves of high-strength concrete. ACI Mater J 94:209–219
Fanella DA, Naaman AE (1985) Stress-strain properties of fiber reinforced mortar in compression. ACI J 82(4):475–483
Mansur M, Wee T, Chin M (1994) Some engineering properties of locally produced high-strength concrete. In: Proceedings of 19th conference on our world in concrete and structures, Singapore, pp 97–106
Mansur M, Wee T, Chin M (1995) Derivation of the complete stress–strain curves for concrete in compression. Mag Concr Res 47(173):285–290
Taerwe LR (1992) Influence of steel fibers on strain-softening of high-strength concrete. ACI Mater J 89(1):54–60
Bencardino F, Rizzuti L, Spadea G, Swamy RN (2008) Stress-strain behavior of steel fiber-reinforced concrete in compression. J Mater Civ Eng 20(3):255–263
Wee T, Chin M, Mansur M (1996) Stress-strain relationship of high-strength concrete in compression. J Mater Civ Eng 8(2):70–76
Hertz KD (2005) Concrete strength for fire safety design. Mag Concr Res 57(8):445–453
Khoury GA, Grainger BN, Sullivan PJ (1985) Transient thermal strain of concrete: literature review, conditions within specimen and behaviour of individual constituents. Mag Concr Res 37(132):131–144
Khoury GA, Grainger BN, Sullivan PJ (1985) Strain of concrete during first heating to 600°C under load. Mag Concr Res 37(133):195–215
Kordina K, Wydra W, Ehm C (1986) Analysis of the developing damage of concrete due to heating and cooling. Spec Publ 92:87–114
Youssef M, Moftah M (2007) General stress–strain relationship for concrete at elevated temperatures. Eng Struct 29(10):2618–2634
Mansur M, Chin M, Wee T (1999) Stress-strain relationship of high-strength fiber concrete in compression. J Mater Civ Eng 11(1):21–29
Candappa D, Sanjayan J, Setunge S (2001) Complete triaxial stress-strain curves of high-strength concrete. J Mater Civ Eng 13(3):209–215
Khoury GA (2000) Effect of fire on concrete and concrete structures. Prog Struct Mat Eng 2(4):429–447
Kodur V, Wang T, Cheng F (2004) Predicting the fire resistance behaviour of high strength concrete columns. Cem Concr Compos 26(2):141–153
Gawin D, Pesavento F, Schrefler B (2004) Modelling of deformations of high strength concrete at elevated temperatures. Mater Struct 37(4):218–236
Kodur V (2000) Spalling in high strength concrete exposed to fire—concerns, causes, critical parameters and cures. In: Proceedings: ASCE structures congress, pp 1–8
Aslani F, Bastami M (2011) Constitutive relationships for normal- and high-strength concrete at elevated temperatures. ACI Mater J 108(4):355–364
ACI-TMS Committee 216 (2007) Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies (ACITMS 216.1-07). American Concrete Institute, Farmington Hills, MI
Bastami M, Aslani F (2010) Preloaded high-temperature constitutive models and relationships for concrete. Sci Iran Trans A Civ Eng 17(1):11
American Concrete Institute (ACI 318-08 & commentary) (2008) Standardization of Building code requirements for structural concrete
American Society of Civil Engineers, ASCE/SFPE29 (1999) Standard Calculation Method for Structural Fire Protection, Reston, VA
European Committee for Standardization (1994). Eurocode 4: Design of composite steel and concrete structures -Part 1-2: General rules-Structural fire design. ENV 1992-1-2. Brussels, Belgium
Beton (CEB) CE-ID (1991) Fire design ofconcrete structures-in accordance with CEBIFIP model code 90 (final draft). CEB Bulletin D’lnjormation, Switzerland
Abrams MS (1981) Guide for determining the fire endurance of concrete elements. American Concrete Institute, Report No ACI 216R-81, Concrete International, pp 13–47
Acknowledgements
Funding was provided by Ministry of Higher Education, Malaysia (Grant No. FP046-2014B), Universiti Malaya (Grant No. BK024-2011B).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Shah, S.N.R., Akashah, F.W. & Shafigh, P. Performance of High Strength Concrete Subjected to Elevated Temperatures: A Review. Fire Technol 55, 1571–1597 (2019). https://doi.org/10.1007/s10694-018-0791-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10694-018-0791-2