Advertisement

Journal of Artificial Organs

, Volume 21, Issue 3, pp 387–391 | Cite as

Wall thickness control in biotubes prepared using type-C mold

  • Takeshi Terazawa
  • Takanori Nishimura
  • Tomohiro Mitani
  • Osamu Ichii
  • Teppei Ikeda
  • Keigo Kosenda
  • Eisuke Tatsumi
  • Yasuhide Nakayama
Brief Communication Tissue Engineering / Regenerative Medicine

Abstract

A type-C mold based on in-body tissue architecture was previously developed for preparing small-diameter biotube vascular grafts with a 2-mm diameter and approximately 1-mm wall thickness. In this study, the type-C mold was modified for preparing large-diameter biotubes with controlled wall thicknesses. Four types of molds were assembled by inserting silicone center rods (outer diameters 11, 13, 15, 17 mm) into stainless steel cages (inner diameter 19 mm) and surgically embedded in the abdominal subcutaneous pouches of Holstein cows. After 8–12 weeks, connective tissues occupied the rod–cage gap in the molds to form biotubes. The wall thickness of the biotubes obtained after removing the molds was approximately 1–3 mm, which corresponded to approximately 80% of each gap distance. The breaking strength almost linearly increased with the wall thickness of the biotubes. The strength of the biotubes with wall thickness over 1.5 mm was higher than that of beagle blood vessels. The thickest biotubes were as strong as bovine pericardium and can be used as an alternative trachea graft because of their adequate lumen-holding force.

Keywords

In-body tissue architecture Biotube Connective tissue Tubular tissue 

Notes

Compliance with ethical standards

Conflict of interest

The authors declare that they have no conflict of interest associated with this work.

References

  1. 1.
    Nakayama Y, Furukoshi M. Feasibility of in-body tissue architecture (IBTA) in pediatric cardiovascular surgery: development of regenerative autologous tissues with growth potential. Pediatr Cardiol Card Surg. 2016;32:199–207.CrossRefGoogle Scholar
  2. 2.
    Furukoshi M, Moriwaki T, Nakayama Y. Development of an in vivo tissue-engineered vascular graft with designed wall thickness (biotube type C) based on a novel caged mold. J Artif Organs. 2016;19:54–61.CrossRefPubMedGoogle Scholar
  3. 3.
    Ozaki S, Kawase I, Yamashita H, Uchida S, Takatoh M, Hagiwara S, Kiyohara N. Aortic valve reconstruction using autologous pericardium for aortic stenosis. Circ J. 2015;79:1504–10.CrossRefPubMedGoogle Scholar
  4. 4.
    Itoh M, Nakayama K, Noguchi R, Kamohara K, Furukawa K, Uchihashi K, Toda S, Oyama J, Node K, Morita S. Scaffold-free tubular tissues created by a Bio-3D printer undergo remodeling and endothelialization when implanted in rat aortae. PLoS One. 2015;10:e0136681.CrossRefPubMedPubMedCentralGoogle Scholar
  5. 5.
    Shimizu T, Yamato M, Kikuchi A, Okano T. Two-dimensional manipulation of cardiac myocyte sheets utilizing temperature-responsive culture dishes augments the pulsatile amplitude. Tissue Eng. 2001;7:141–51.CrossRefPubMedGoogle Scholar
  6. 6.
    Shimizu T, Sekine H, Yang J, Isoi Y, Yamato M, Kikuchi A, Kobayashi E, Okano T. Polysurgery of cell sheet grafts overcomes diffusion limits to produce thick, vascularized myocardial tissues. FASEB J. 2006;20:708–10.CrossRefPubMedGoogle Scholar
  7. 7.
    Novosel EC, Kleinhans C, Kluger PJ. Vascularization is the key challenge in tissue engineering. Adv Drug Deliv. 2011;63:300–11.CrossRefGoogle Scholar
  8. 8.
    Satake R, Komura M, Komura H, Kodaka T, Terawaki K, Ikebukuro K, Komuro H, Yonekawa H, Hoshi K, Takato T, Nakayama Y. Patch tracheoplasty in body tissue engineering using collagenous connective tissue membranes (biosheets). J Pediatr Surg. 2016;51:244–8.CrossRefPubMedGoogle Scholar
  9. 9.
    Okuyama H, Umeda S, Takama Y, Terasawa T, Nakayama Y. Patch esophagoplasty using an in-body-tissue-engineered collagenous connective tissue membrane. J Pediatr Surg. 2018;53:223–6.CrossRefPubMedGoogle Scholar

Copyright information

© The Japanese Society for Artificial Organs 2018

Authors and Affiliations

  1. 1.Department of Artificial OrgansNational Cerebral and Cardiovascular Center Research InstituteSuitaJapan
  2. 2.Research Faculty of Agriculture, Graduate School of AgricultureHokkaido UniversitySapporoJapan
  3. 3.Field Science Center for Northern BiosphereHokkaido UniversitySapporoJapan
  4. 4.Laboratory of Anatomy, Department of Basic Veterinary Sciences, Faculty of Veterinary MedicineHokkaido UniversitySapporoJapan
  5. 5.BRAST Livestock ClinicBRAST Inc.SapporoJapan
  6. 6.Shibetsu Veterinary Clinical CenterHokkaidochuo Agricultural Mutual Aid AssociationShibetsuJapan

Personalised recommendations