Advertisement

European Journal of Wood and Wood Products

, Volume 76, Issue 3, pp 823–831 | Cite as

Effects of MDI content on properties of thermally treated oriented strand board (OSB)

  • Martin Direske
  • Juergen Bonigut
  • Christoph Wenderdel
  • Wolfram Scheiding
  • Detlef Krug
Original
First Online:
Received:

Abstract

The paper discusses the influence of methylene diphenyl diisocyanate (MDI) content on mechanical properties of thermally post-treated single-layered oriented strand boards (OSB). The OSB differed in adhesive content (3, 4 and 5%) and the high temperature (HT) level of the thermal modification (TM) (untreated, 160, 175 °C). To characterise the mechanical behaviour of the OSB, the modulus of rupture (MOR), modulus of elasticity (MOE), and internal bond (IB) of dry and boiled specimens were determined. In addition, the adsorption and desorption isotherms were investigated. The hygroscopic sorption isotherms were calculated according to the Hailwood-Horrobin equation. It was observed that the MOR and the IB of the post-treated OSB are significantly increased with higher MDI content. An increase of the MDI content from 3% up to 5% is not sufficient to compensate the loss of strength caused by TM. However, an increase of MDI-content of about 1% compensates the significant loss of IB of dry and boiled specimens. The MOE is not influenced by TM. With increased adhesive content, thermally treated and untreated specimens show slightly higher values. The thermal post-treatment of OSB alters the wood-water-interaction. The hygroscopicity is reduced. The higher the HT level, the lower is the sorption behaviour. It was also detected that a higher MDI content does not influence the hygroscopicity.

This is a preview of subscription content, log in to check access.

References

  1. Aro MD, Brashaw BK, Donahue PK (2014) Mechanical and physical properties of thermally modified plywood and oriented strand board panels. Forest Prod J 64(7/8):281–289CrossRefGoogle Scholar
  2. Bonigut J, Krug D (2011) Properties of thermally modified oriented strandboards (OSB). In: Forest products society 65th international conference. Proceedings, PortlandGoogle Scholar
  3. Bonigut J, Krug D, Stephani B (2012) Properties of thermally modified medium-density fibreboards. Holzforschung 66(1):79–83CrossRefGoogle Scholar
  4. Bonigut J, Krug D, Stuckenberg P (2014) Dimensional stability and irreversible thickness swell of thermally treated oriented strandboards (OSB). Eur J Wood Prod 72(5):593–599CrossRefGoogle Scholar
  5. Boonstra MJ, Tjeerdsma B (2006) Chemical analysis of heat treated softwoods. Holz Roh Werkst 64(3):204–211CrossRefGoogle Scholar
  6. Del Menezzi CHS, Tomaselli I (2006) Contact thermal post-treatment of oriented strandboard to improve dimensional stability: a preliminary study. Holz Roh Werkst 64(3):212–217CrossRefGoogle Scholar
  7. Del Menezzi CHS, de Souza RQ, Thompson RM, Teixeira DE, Okino EYA, da Costa AF (2008) Properties after weathering and decay resistance of a thermally modified wood structural board. Int Biodeterior Biodegrad 62(4):448–454CrossRefGoogle Scholar
  8. Del Menezzi CHS, Tomaselli I, Okino EYA, Teixeira DE, Santana MAE (2009) Thermal modification of consolidated oriented strandboards: effects on dimensional stability, mechanical properties, chemical composition and surface color. Eur J Wood Prod 67(4):383–396Google Scholar
  9. EN 1087 (1995) Particleboards—determination of moisture resistance—Part 1: Boil testGoogle Scholar
  10. EN 310 (1993) Wood-based panels—determination of modulus of elasticity in bending and of bending strengthGoogle Scholar
  11. EN 319 (1993) Particleboards and fibreboards—determination of tensile strength perpendicular to the plane of the boardGoogle Scholar
  12. EN 322 (1993) Wood-based panels—determination of moisture contentGoogle Scholar
  13. EN 323 (1993) Wood-based panels—determination of densityGoogle Scholar
  14. Esteves B, Domingos I, Pereira H (2008) Pine wood modification by heat treatment in air. BioResources 3(1):142–154Google Scholar
  15. Hailwood AJ, Horrobin S (1946) Absorption of water by polymers: analysis in terms of a simple model. Trans Faraday Soc 42:B084-B092CrossRefGoogle Scholar
  16. Hartley ID, Wang S, Zhang Y (2007) Water vapor sorption isotherm modeling of commercial oriented strand panel based on species groups and resin type. Build Environ 42(10):3655–3659CrossRefGoogle Scholar
  17. Hill CA, Ramsay J, Keating B, Laine K, Rautkari L, Hughes M, Constant B (2012) The water vapour sorption properties of thermally modified and densified wood. J Mat Sci 47(7):3191–3197CrossRefGoogle Scholar
  18. Jalaludin Z, Hill CA, Xie Y, Samsi HW, Husain H, Awang K, Curling SF (2010) Analysis of the water vapour sorption isotherms of thermally modified acacia and sesendok. Wood Mat Sci Eng 5(3–4):194–203CrossRefGoogle Scholar
  19. Kollmann F, Fengel D (1965) Changes in chemical composition of wood by thermal treatment. Holz Roh Werkst 23(12):461–468CrossRefGoogle Scholar
  20. Lee SH, Lum WC, Zaidon A, Maminski M (2015) Microstructural. mechanical and physical properties of post heat-treated melamine-fortified urea formaldehyde-bonded particleboard. Eur J Wood Prod 73(5):607–616CrossRefGoogle Scholar
  21. Mendes RF, Júnior GB, de Almeida NF, Surdi PG, Barbeiro IN (2013) Effect of thermal treatment on properties of OSB panels. Wood Sci Technol 47(2):243–256CrossRefGoogle Scholar
  22. Mohebby B, Ilbeighi F, Kazemi-Najafi S (2008) Influence of hydrothermal modification of fibers on some physical and mechanical properties of medium density fiberboard (MDF). Holz Roh Werkst 66(3):213–218CrossRefGoogle Scholar
  23. Neimsuwan T, Wang S, Taylor AM, Rials TG (2008) Statics and kinetics of water vapor sorption of small loblolly pine samples. Wood Sci Technol 42(6):493–506CrossRefGoogle Scholar
  24. Ohlmeyer M, Kruse K (1999) Hot stacking and its effects on panel properties. In: European Panel Products Symposium. 3. Proceedings, Llandudno pp 293–300Google Scholar
  25. Ohlmeyer M, Paul W (2010) Optimierung der Eigenschaften von Holzwerkstoffen mit Hilfe von thermischen Modifizierungsmethoden (Optimisation of properties of wood products by means of thermal modification) (In German). vTI, p 228Google Scholar
  26. Okino EY, Teixeira DE, Del Menezzi CH (2007) Post-thermal treatment of oriented strandboard (OSB) made from cypress (Cupressus glauca Lam.). Maderas Cienc Tecnol 9(3):199–210CrossRefGoogle Scholar
  27. Olek W, Majka J, Czajkowski Ł (2013) Sorption isotherms of thermally modified wood. Holzforschung 67(2):183–191CrossRefGoogle Scholar
  28. Paul W, Ohlmeyer M, Leithoff H, Boonstra MJ, Pizzi A (2006) Optimising the properties of OSB by a one-step heat pre-treatment process. Holz Roh Werkst 64(3):227–234CrossRefGoogle Scholar
  29. Paul W, Ohlmeyer M, Leithoff H (2007) Thermal modification of OSB-strands by a one-step heat pre-treatment–Influence of temperature on weight loss, hygroscopicity and improved fungal resistance. Holz Roh Werkst 65(1):57–63CrossRefGoogle Scholar
  30. Pétrissans M, Gérardin P, Serraj M (2003) Wettability of heat-treated wood. Holzforschung 57(3):301–307CrossRefGoogle Scholar
  31. Richards RF, Burch DM, Thomas WC (1993) Water vapor sorption measurements of common building materials. Trans Am Soc Heat Refrig Air Cond Eng 98:475–475Google Scholar
  32. Roffael E, Rauch W (1973) Einfluß von Temperatur und thermischer Nachbehandlung auf einige physikalische Eigenschaften von diisocyanat-gebundenen Spanplatten (Influence of temperature and thermal post-treatment on some physical properties of diisocyanate bonded particle board) (In German). Holz Roh Werkst 31(10):402–405CrossRefGoogle Scholar
  33. Scheiding W, Flade P, Plaschkies K (2012) Sandwich stacking—a smart innovation for thermal modification in open kilns. In: European Conference on Wood Modification. 6. Proceedings, Ljubljana, pp 21–28Google Scholar
  34. Sekino N, Inoue M, Irle M, Adcock T (1999) The mechanisms behind the improved dimensional stability of particleboards made from steam-pretreated particles. Holzforschung 53(4):435–440CrossRefGoogle Scholar
  35. Umemura K, Kawai S (2002) Effect of polyol on thermo-oxidative degradation of isocyanate resin for wood adhesives. J Wood Sci 48(1):25–31CrossRefGoogle Scholar
  36. Wangaard FF, Granados LA (1967) The effect of extractives on water-vapor sorption by wood. Wood Sci Technol 1(4):253–277CrossRefGoogle Scholar
  37. Winandy JE, Lebow PK (2001) Modelling strength loss in wood by chemical composition. Part I. An individual component model for southern pine. Wood Fiber Sci 33(2):239–254Google Scholar
  38. Windeisen E, Wegener G (2008) Behaviour of lignin during thermal treatments of wood. Ind Crops Prod 27(2):157–162CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany 2017

Authors and Affiliations

  • Martin Direske
    • 1
  • Juergen Bonigut
    • 1
  • Christoph Wenderdel
    • 1
  • Wolfram Scheiding
    • 1
  • Detlef Krug
    • 1
  1. 1.Institute of Wood Technology Dresden (IHD)DresdenGermany

Personalised recommendations

Cite article

Buy options