Skip to main content
SpringerLink
Log in

Examination of tools of different materials edge geometry for MDF milling

Untersuchung von Werkzeugen mit unterschiedlicher Schneidengeometrie zum Fräsen von MDF

  • Originals Originalarbeiten
  • Published:
European Journal of Wood and Wood Products Aims and scope Submit manuscript

Abstract

Most of the investigations directed to find the relation between tool wear and the wood-based panel characteristics concern particleboard cutting. The goal of this paper was to characterize the optimal edge geometry, in case of wear, when milling the medium-density fibreboard, for blades produced from different materials.

Zusammenfassung

Die meisten Untersuchungen über den Zusammenhang von Werkzeugverschleiß und den Eigenschaften von Holzwerkstoffplatten beziehen sich auf die Bearbeitung von Spanplatten. Ziel dieser Studie war es, die optimaleSchneidengeometrie unterschiedlicher Sägeblattmaterialien für das Fräsen von MDF in Abhängigkeit vom Werkzeugverschleiß zu bestimmen.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Böhme C, Münz U (1987) Zerspanungsverhalten und Verschleißwirkung von Normal- und Sonderplatten mit einheitlicher Beschichtung bei Anwendung unterschiedlicher Zerspanungsverfahren. Fraunhofer Institut für Holzforschung. WKI-Bericht 17, Braunschweig, S 106

    Google Scholar 

  2. Beer P, Marchal R, Butaud J-C, Sokołowska A, Lambertin M, Miklaszewski S (1997) Analysis of the rotary peeling of beech wood using tools covered with antiabrasive coatings, Proceeding of 13th International Wood Machining Seminar, UBC Vancouver, Canada, 1997, pp 699–707

  3. Bridges RR (1971) A quantitative study of some factors affecting the abrasiveness of particleboard. For Prod J 11:39–41

    Google Scholar 

  4. Döry L (2006) Report of the European Panel Federation. 5th European Wood-Based Panel Symposium, Hannover, Germany, 4.–6. Oct 2006

    Google Scholar 

  5. Feld H, Steward J, Horn T, Schulte R (2005) Carbide selection for woodworking tooling. Proc. of IWMS 17, Rosenheim, Germany, 26.–28. Sep 2005

  6. Kowaluk G, Beer P, Palubicki B, Frackowiak I (2007a) Different types of tool blunting during milling of particleboards from wooden chips and rape straw parts. DREWNO – WOOD 2007, vol 50, nr 177

  7. Kowaluk G, Szymanski W, Beer P, Sinn G, Gindl M (2007b) Influence of tools stage on particleboards milling. Wood Res 52(3):75–88

    Google Scholar 

  8. Kowaluk G, Szymanski W, Palubicki B, Beer P (2006) Quality of milling of laminated particleboard correlated to cutting parameters. Proc. of Joint Meeting of ESWM and COST Action E35, Florence, Italy, 14.–17. May 2006

  9. Lin RJT, van Houts J, Bhattacharya D (2006) Machinability investigation of medium-density fibreboard. Holzforschung 60:71–77

    Article  CAS  Google Scholar 

  10. Marchal R, Jullien D, Mothe F, Thibaut B (1993) Mechanical aspects of heating wood in rotary veneer cutting. Proceeding of 11th International Wood Machining Seminar, Honne, Norway, 1993:257–278

  11. Pahlitzsch G, Jostmeier H (1964) Beobachtungen über das Abstumpfungsverhalten beim Fräsen von Spanplatten. Holz Roh- Werkst 139–146

  12. Plastov EF (1971) Influence of the carbide tool bluntness on qualitative factors and forces during milling of particleboards (Vlijahie zatuplehija tverdocplavnykh rezcov na kachestvennye i silovye pokazateli processa frezovania kromok derevostruchnych plit). Driev Prom 6:9–10

    Google Scholar 

  13. Salje E, Drückhammer J (1984) Qualitätskontrolle bei der Kantenbearbeitung. Holz Roh- Werkst 42:187–192

    Article  Google Scholar 

  14. Salje E, Stühmeier W (1988) Milling laminated chipboard with tungsten carbide and PCD. Ind Diam Rev 4:319–326

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Wood Technology Institute, Winiarska Str. 1, 60-654, Poznan, Poland

    Grzegorz Kowaluk

  2. Department of Woodworking Machinery and Basis of Machine Construction, The August Cieszkowski Agricultural University of Poznan, Poznan, Poland

    Waldemar Szymanski

  3. ENSAM Cluny, LaBoMaP – Equipe Bois, Cluny, France

    Bartosz Palubicki

  4. Department of Construction and Technology of Final Wood Products, Warsaw University of Life Science, Warsaw, Poland

    Piotr Beer

Authors
  1. Grzegorz Kowaluk
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Waldemar Szymanski
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Bartosz Palubicki
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Piotr Beer
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Grzegorz Kowaluk.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Kowaluk, G., Szymanski, W., Palubicki, B. et al. Examination of tools of different materials edge geometry for MDF milling . Eur. J. Wood Prod. 67, 173–176 (2009). https://doi.org/10.1007/s00107-008-0302-0

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00107-008-0302-0

Keywords

Search

Navigation