Zusammenfassung
Fichtenkantholz wurde unter geringem Druck bei einer Temperatur von 140°C auf einer Mehretagenpresse senkrecht zur Faser auf 50% des Volumens verdichtet, wobei der Prozess in drei Stufen erfolgte: Erhitzen, Verdichten, Rückkühlen. Die mechanischen Eigenschaften des Pressholzes wurden anschließend an fehlerfreien Kleinproben ermittelt. Es hat sich gezeigt, dass anatomischer Aufbau, Anisotropie, Rohdichte und Feuchtigkeit das Ergebnis beeinflussen, und dass die Erhöhung der Steifigkeit und Festigkeit sich meist proportional zur Verdichtung einstellte. Schädigungen infolge von Faserabweichungen, Ästen oder anderen Holzfehlern traten nur sehr begrenzt auf. In Abhängigkeit von Zeit und Höhe der Temperatureinwirkung verändern sich die Festigkeit, die Holzfärbung sowie das Quell- und Schwindverhalten.
Abstract
Sawn spruce wood was compressed perpendicular to grain to 50% of its original volume at a temperature of 140 °C in a multiple daylight press. The process had three steps: heating up—compression—and cooling. The mechanical properties of clear samples from densified wood were investigated thereafter. Test results show that the mechanical characteristics are influenced by wood anatomy, anisotropy and moisture content and that strength and stiffness are proportional to the increase of density. Strength, color, as well as swelling, depend on the parameters of the process especially temperature and duration of heating. Damages due to grain deviation or knots were rarely observed. Bending and tensile strength amount to 169 and 185 Mpa, respectively, compression strength perpendicular to grain benefits most from transverse compression reaching a factor of 4.4 times the non-densified reference samples.
Literatur
Haller P, Wehsener J (2003) Entwicklung innovativer Verbindungen aus Pressholz und Glasfaserarmierung für den Ingenieurholzbau. Fraunhofer IRB Verlag, Stuttgart
Herzog T, Naterer J, Schweitzer R, Volz M, Winter W (2003) Holzbauatlas. Institut für internationale Architektur-Dokumentation GmbH & Co. KG, München
Inoue M, Minato K, Norimoto M (1994) Permanent fixation of compressive deformation of wood by crosslinking. Mokuzai Gakkaishi 40(9):931–936
Kollmann F (1955) Technologie des Holzes und der Holzwerkstoffe, Bd 2. Springer, Berlin Heidelberg New York
Leijten A (1998) Densified veneer wood reinforced timber joints with expanded tube fasteners. Delft University of Technology; Delft University Press, Netherlands
Navi P, Tomme F-Ph, Gfeller B, Giradet F (1998) Densified wood: an innovative product with highly enhanced characters. In: Naterer J, Sandoz JL (Hrsg) Tagungsband. 5th World Conference on Timber Engineering, vol 2, Montreux, Schweiz, S 640–647
Navi P, Giradet F (2000) Effects of thermo-hydro-mechanical treatment on the structure and properties of wood. Holzforschung 54:287–293
Norimoto M, Ota Ch, Akitsu H, Yamada T (1993) Permanent fixation of bending deformation in wood by heat treatment. Wood Research 79:23–33
Schrepfer V (1997) Formvollholz für den Baueinsatz. Eidgenössische Technische Hochschule Zürich, Professur für Holztechnologie 97-1:10
Tanahashi M et al. (1998) Compressive-molding of wood by high-pressure steam treatment. Part 1. Holzforschung 52:211–216
Vorreiter L (1949) Holztechnologisches Handbuch, Bd 2. Georg Fromme, Wien
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Haller, P., Wehsener, J. Festigkeitsuntersuchungen an Fichtenpressholz (FPH). Holz Roh Werkst 62, 452–454 (2004). https://doi.org/10.1007/s00107-004-0516-8
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00107-004-0516-8