Abstract
The present paper reports the results of an investigation regarding the design of a method for visually grading sawn timber of Argentinean Eucalyptus grandis. An empirical research project with four samples of beams and one sample of boards subjected to bending, one sample of boards subjected to tension and one sample of specimens subjected to compression, was carried out. The results obtained with specimens in structural sizes show the influence of the more important strength and stiffness reducing growth characteristics and allow to analyse different strength, stiffness and density profiles in comparison with the international strength class system established in the European standard EN 338. The research also reveals particularities for this timber species as the high ratio of modulus of elasticity and strength to density, in comparison with other deciduous species, among others.
Zusammenfassung
Dieser Beitrag fasst die Ergebnisse einer Studie zusammen, in der die Möglichkeiten einer visuellen Festigkeitssortierung von Eucalyptus grandis aus Argentinien untersucht wurden. Die Untersuchung umfasste vier Teilstichproben mit Kanthölzern und eine Teilstichprobe mit Brettern in Biegeversuchen und jeweils eine Teilstichprobe mit Zug- bzw. Druckprüfkörpern. Die Ergebnisse der Versuche mit Prüfkörpern in Bauholzabmessungen zeigen den Einfluss der wichtigsten visuellen Sortierparameter und erlauben die Einteilung von Bauholz aus Eucalyptus grandis in unterschiedliche Festigkeitsklassen nach EN 338. Die vorliegende Studie zeigt darüber hinaus besondere Eigenschaften dieser Laubholzart wie das hohe Verhältnis von Elastizitätsmodul und Festigkeit zur Rohdichte.
Similar content being viewed by others
References
ABNT-Associaçao Brasileira de Normas Técnicas (1997) NBR 7190, Projeto de estructuras de Madeira. ABNT, Brasil
American Society for Testing and Materials (1999) ASTM D 245-98, Standard practice for establishing structural grades and related allowable properties for visually graded lumber. ASTM, West Conshohocken, PA.
Burger N, Glos P (1997) Verhältnis von Zug- zu Biegefestigkeit bei Vollholz. Holz Roh- Werkstoff 55:345–350
Burger N, Glos P (1995) Verhältnis zwischen Zug- und Biege-Elastizitätsmoduln von Vollholz. Holz Roh- Werkstoff 53:73–74
Comité Europeo de Normalización (1997) UNE-EN 1310, Madera aserrada y madera en rollo. Método de medida de las singularidades. AENOR, Madrid
Dadswell H (1972) The anatomy of eucalypt woods. CSIRO Div Appl Chem Tech Pap No 66, Australia
Europäisches Komitee für Normung (1996) DIN EN 338, Bauholz für tragende Zwecke, Festigkeitsklassen. Beuth Verlag, Berlin
Europäisches Komitee für Normung (1996) DIN EN 384, Bauholz für tragende Zwecke, Bestimmung charakteristischer Festigkeits-, Steifigkeits- und Rohdichtewerte. Beuth Verlag, Berlin
Europäisches Komitee für Normung (1996) DIN EN 408, Holzbauwerke, Bauholz für tragende Zwecke und Brettschichtholz, Bestimmung einiger physikalischer und mechanischer Eigenschaften. Beuth Verlag, Berlin
Europäisches Komitee für Normung (1999) DIN EN 1194, Holzbauwerke, Brettschichtholz, Festigkeitsklassen und Bestimmung charakteristischer Werte. Beuth Verlag, Berlin
European Committee for standardization (2000) Draft prEN 14081-1, Timber structures—strength graded structural timber with rectangular cross section—part 1: general requirements. CEN, Brussels
Glos P (1995) Strength grading. In: Timber Engineering STEP 1. Centrum Hout, The Netherlands, , pp A6/1–A6/8
Glos P, Diebold R (1987) Einfluß verschiedener Sortierbedingungen auf die Biegefestigkeit von Bauholz (Kantholz). Abschlußbericht 84510, Institut für Holzforschung, Universität München, München
Glos P, Lederer B (2000) Sortierung von Buchen- und Eichenschnittholz nach der Tragfähigkeit und Bestimmung der zugehörigen Festigkeits- und Steifigkeitskennwerte. Bericht Nr. 98508, Holzforschung, München
Glos P, Tratzmiller M (1996) Höherwertige Starkholznutzung durch verbesserte Einschnitt- und Sortierverfahren. Abschlußbericht 94506 an LWF, München
Hillis WE (1978) Wood quality and utilization. In: Hillis WE, Brown AG (eds) Eucalypts for wood production. CSIRO, Melbourne, pp 258–289
Hermoso Prieto E (2001) Caracterización mecánica de la madera estructural de Pynus sylvestris L.. Tesis Doctoral, Universidad Politécnica de Madrid, Escuela Técnica Superior de Ingenieros de Montes, Madrid
Hoffmeyer P. (1995) Wood as a building material. In: Timber Engineering STEP 1. Centrum Hout, The Netherlands, pp A4/1–A4/21
INTA-Instituto Nacional de Tecnología Agropecuaria (1995) Manual para Productores de Eucaliptos de la Mesopotamia Argentina. Grupo Forestal, EEA INTA Concordia, Argentina
International Organization for Standardization (1975) ISO 3130–1975 (E), Wood—determination of moisture content for physical and mechanical tests
International Organization for Standardization (1975) ISO 3131-1975 (E), Wood—determination of density for physical and mechanical tests
Johansson CJ, Brundin J, Gruber R (1992) Stress grading of Swedish and German timber, a comparison of machine stress grading and three visual grading systems. SP Report 1992:23, Swedish National Testing and Research Institute, Sweden
Pérez del Castillo A (2001) Propiedades Mecánicas y Calidad de Madera de Eucalyptus Grandis del Norte de Uruguay. Informe de Investigación Nº4, LATU, Montevideo
Standards Australia (1986) AS 2878–1986, Timber—classification into strength groups. Standards Australia, North Sydney, N.S.W.
Standards Australia (2000) AS 2082/2000, Timber—hardwood—visually stress-graded for structural purposes. Standards Australia, Australia
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Piter, J.C., Zerbino, R.L. & Blaß, H.J. Visual strength grading of Argentinean Eucalyptus grandis . Holz Roh Werkst 62, 1–8 (2004). https://doi.org/10.1007/s00107-003-0433-2
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00107-003-0433-2