Skip to main content
Log in

Effect of Nano Metallic Fe on Al5O6N Synthesis in Al2O3-C Refractories

  • Special Technologies
  • Published:
Interceram - International Ceramic Review

Abstract

Al2O3-C refractory samples were prepared using corundum, flake graphite, Al and Si powders and phenolic resin as raw materials. The in-situ synthesis mechanism of Al5O6N in Al2O3-C refractories was studied and the effect of adding nano metallic Fe on the formation and microstructure of Al5O6N phase was also investigated. Thermodynamic calculations show that Al5O6N can potentially be synthesized in a reducing atmosphere at 1600°C over a narrow range of N2 and CO pressures. Experimental results proved that Al5O6N phase was synthesized after 1600°C heat treatment when nano Fe was added to Al2O3-C refractories. As the content of nano Fe increases, Al5O6N particles show disappearance of oriented growth, with octahedron shapes turning into spherical agglomerations.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Similar content being viewed by others

References

  1. Yamaguchi, A.: The carbon composite refractory. Refractories 28 (1994) 128–132

    CAS  Google Scholar 

  2. Li, X.C., Zhu, B.Q., Zhao, F.: In-situ synthesis of SiC and β-Si3Al3O3N5 whiskers in alumina carbon based materials. Mater. Sci. Forum 745–746 (2013) 663–665

    Article  CAS  Google Scholar 

  3. Li, X.C., Li, Y.X., Zhu, B.Q.: Matrix structure evolution and thermo-mechanical properties of carbon fiber-reinforced Al2O3-SiC-C castable composites. Mater. Res. Bull. 61 (2014) 201–206

    Article  CAS  Google Scholar 

  4. Zhu, B.Q., Zhu, Y.N., Li, X.C., et al.: Effect of ceramic bonding phases on the thermo-mechanical properties of Al2O3-C refractories. Ceram. Int. 39 (2013) 6069–6076

    Article  CAS  Google Scholar 

  5. Antsiferov, V.N., Gilyov, V.G., Karmanov, V.I.: IR-spectra and phases structure of sialons. Vibr. Spectros. 30 (2002) 169–173

    Article  CAS  Google Scholar 

  6. Willems, H.X., Hendrix, M.R., Metselaar, R., et al.: Strength and microstructure of silicon nitride/aluminum interface fabricated by squeeze cast brazing. J. Eur. Ceram. Soc. 12 (1993) 43–49

    Article  CAS  Google Scholar 

  7. Wang, Z.S., Liu, J.X., Li, F.S.: The fabrication and characterization of Al5O6N nano powders. J. Chin. Ceram. Soc. 36 (2008) 580–583

    CAS  Google Scholar 

  8. Wei, G.P., Zhu, B.Q., Li, X.C., et al.: Microstructure and mechanical properties of low-carbon MgO-C refractories bonded by an Fe nanosheet-modified phenol resin. Ceram. Int. 41 (2015) 1553–1566

    Article  CAS  Google Scholar 

  9. McCauley, J.W., Corbin, N.D.: High Temperature reactions and microstructures in the Al2O3-AlN System. Progress in Nitrogen Ceramics 65 (1983) 111–118

    Article  CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Xiangcheng Li.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Tan, X., Zhao, Z., Chen, P. et al. Effect of Nano Metallic Fe on Al5O6N Synthesis in Al2O3-C Refractories. Interceram. - Int. Ceram. Rev. 64, 108–111 (2015). https://doi.org/10.1007/BF03401110

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF03401110

Keywords

Navigation