Abstract
This paper deals with the machining issues of two titanium alloys using two cutting tools. With respect to the given issue, a larger part of the article is devoted to metallographic analysis of both materials. The following is a description of the tools and machining conditions. Further, there is a description of a milling test of both alloys by end mills while sensing the force load by piezoelectric dynamometer. The last section evaluates and compares the obtained data. Based on the information obtained, the conclusion evaluates the problems encountered when machining, which correspond to the material properties.
Similar content being viewed by others
References
Warchomicka, F., Stockinger, M., Degischer, H.P., “Flow behaviour and microstructure during hot deformation of Ti-5Al-5Mo-5V-3Cr-1Zr,” Institut für Werkstoffwissenschaft und Werkstofftechnologie [online]. 2007 [vid. 2013-05-13]. Dostupné z: http://wwwt.tuwien.ac.at/fileadmin/t/wwwt/forschung/GW/Bilder/Ti2007_%20Warchomicka_01.pdf. (last accessed on 1-13-15).
Wu, X., “Review of alloy and process development of TiAl alloys,” Intermetallics, ISSN: 0966-9795, vol. 14, no. 10–11, pp. 1114–1122 (2006).
Agote, I., et al., “Microstructure and mechanical properties of gamma TiAl based alloys produced by combustion synthesis + compaction route,” Intermetallics, ISSN: 0966-9795, vol. 16, no. 11–12, pp. 1310–1316 (2008).
Ježová, Z., Bajana, O., Lapin, J., “Effect of heat treatments on the microstructure and mechanical properties of intermetallic TiAl-based alloy,” in Technológia 2005, Bratislava, 2005, s. 132–137.
Úvodní strana, Gühring [online], c 2013 [vid. 2013-03-17]. Dostupné z: http://www.guhring.cz/uvodni-stranka.
Frézy: Kompletní Program 2007, Guhring, [online]. 2007 [vid. 2013-04-05]. Dostupné z: http://www.guhring.cz/data/produkty/cz_18.pdf.
Kennametal Inc., Aerospace: Sustainable Solutions, Latrobe, Pennsylvania, USA (2011). Dostupné z: http://www.kennametal.com/content/dam/kennametal/kennametal/common/Resources/Catalogs-Literature/Industry%20Solutions/A-09-02311_aerospace_catalog.pdf.
Kennametal Inc., Harvi II Carbide End Mills: 5 Flutes with Unequal Flute Spacing, Latrobe, Pennsylvania, USA (2008).
Upínače nástrojů (2), Technický týdeník [online]. 2012 [vid. 2013-04-05]. Dostupné z: http://www.technickytydenik.cz/rubriky/serialy/upinace-nastroju/upinace-nastroju-2_8498.html.
Tepelné upínače nástrojů: DIN 69871 AD / B, TEPELNÉ UPÍNAČE NÁSTROJŮ [online] [2013] [vid. 2013-04-05]. Dostupné z: http://tepelne-upinace.kvalitne.cz/69871.php.
Kuchař, Dušan, Druhá generace tepelných upínačů, MM Průmyslové spektrum [online] (2007) č. 4 [vid. 2013-04-05]. Dostupné z: http://www.mmspektrum.com/clanek/druha-generace-tepelnych-upinacu.html.
Zemčík, L., Dlouhý, A. Tavení intermetalických slitin typu gama TiAl ve vakuových indukčních pecích. Slévárenství (2004), roč. LII, č. 4, s. 223–227, ISSN 0037-6825.
Sung, Si-Young, Kim, Young-Jig., “Melting and Casting of Titanium Alloys,” Intermetallics (2007) vol. 15, is. 4, s. 468–474, ISSN: 0966-9795.
Leyens, Ch., Peters, M., „Titanium and Titanium Alloys, Fundamentals and Applications,“ 2nd ed., Willet-VCH, Köln (2005) p. 513, ISBN 3-527-30534-3.
Bumbálek, B., Výbĕr řezných materiálů a optimálních řezných podmínek ro obrábĕní niklových a titanových slitin, Shrnutí dosavadních zkušeností, Brno: Vojenská akademie Brno, Katedra materiálů a technologie speciální výroby, Duben (1992) 78 s.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Sedlák, J., Drábek, T., Mouralová, K. et al. Machining Issues of Titanium Alloys. Inter Metalcast 9, 41–50 (2015). https://doi.org/10.1007/BF03355614
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF03355614