Advertisement

KSME International Journal

, Volume 13, Issue 3, pp 221–228 | Cite as

Bifurcation analysis of wrinkling formation for anisotropic sheet

  • Young-suk Kim
  • Young-jin Son
  • Jun-young Park
Article

Abstract

Surface distortions in the form of localized buckles and wrinkles are often observed in the sheet metal forming process. In many cases the presence of wrinkles in the final praduct is unacceptable for the purposes of assembly. Because of the trend in recent years towards thinner gauges and higher strength, wrinkling is increasingly becoming a more common and troublesome mode of failure in sheet metal forming. In this study, a numerical analysis for evaluating a wrinkling limit diagram (WLD) for an anisotropic sheet subjected to biaxial plane stress is presented. Here the scheme of plastic bifurcation theory for thin shells based on the Donnell-Mushtari-Viasov shell theory is used. The effects of the various material parameters (yield stress, strain hardening coefficient and normal anisotropy parameter) and geometric parameters on WLD are investigated numerically and compared with Kawai's and Havranek's experiment(1975).

Key Words

Wrinkling Limit Diagram Plastic Bifurcation Theory Normal Anisotropys 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. Ameziane-Hassani, H. and Neale, K. W., 1991, “On the Analysis of Sheet Metal Wrinkling,”J. Mech. Sci., Vol. 33, No. 1, pp. 13–30.MATHCrossRefGoogle Scholar
  2. Havranek, J., 1975, “Wrinkling Limit of Tapered Processing,”J. Australian Inst. Metals, Vol. 20, No. 2, pp. 114–119Google Scholar
  3. Hill, R., 1957, “On the Problem of Uniqueness on the Theory of a Rigid-Plastic Solid (3),”J. Mech. Phys. Solids, Vol. 5, pp. 153–161MATHCrossRefMathSciNetGoogle Scholar
  4. Hill, R., 1958, “A General Theory of Uniqueness and Stability in Elastic-Plastic Solids,”J. Mech. Phys. Solids, Vol. 6, pp. 236–240MATHCrossRefGoogle Scholar
  5. Hosford, W. F., 1979, “On Yield Loci of Anisotropic Cubic Metals”,Proc. 7th North Amer. Metalworking Res. Conf., pp. 191–196Google Scholar
  6. Hutchinson, J. W., 1979, “Plastic Buckling,”Adv. Appl. Mech., Vol. 14, pp. 67–144CrossRefGoogle Scholar
  7. Kim, Y. S. and Park, K. C., 1993, “The Effect of Tensile Properties on Plane Strain Stretchability of Automotive Steel Sheets,”Trans. Korea Soc. Mech. Eng., Vol. 17, No. 11, pp. 2676–2683 (in Korean)Google Scholar
  8. Neale, K. W. and Tugcu, P., 1990, “A Numerical Analysis of Wrinkle Formation Tendencies in Sheet Metals,”Int. J. for Num. Methods in Eng., Vol. 30, pp. 1595–1608CrossRefGoogle Scholar
  9. Park, K. C. and Kim, Y. S., 1995, “The Effect of Material and Process Variables on the Stamping Formability of Sheet Materials,”J. Mat. Proc. Tech., vol. 51, pp. 64–78CrossRefGoogle Scholar
  10. Szacinski, A. M. and Thomson, P. F., 1992, “Critical Conditions for Wrinkling During the Forming of Anisotropic Sheet Metal,”J. Mat. Proc. Tech., Vol. 35, pp. 213–226CrossRefGoogle Scholar
  11. Tomita, Y. and Shindo, A., 1988, “Onset and Growth of Wrinkles in the Square Plate Subjected to Diagonal Tension,”Int. J. Mech. Sci., Vol. 30, No. 12, pp. 921–931MATHCrossRefGoogle Scholar
  12. Triantafyllidis, N. and Needleman, A., 1980, “An Analysis of Wrinkling in the Swift Cup Test,”J. Eng. Mat. Tech., Vol. 102, pp. 241–248CrossRefGoogle Scholar

Copyright information

© The Korean Society of Mechanical Engineers (KSME) 1999

Authors and Affiliations

  • Young-suk Kim
    • 1
  • Young-jin Son
    • 2
  • Jun-young Park
    • 2
  1. 1.Department of Mechanical EngineeringKyungpook National UniversityDaeguKorea
  2. 2.Department of Mechanical EngineeringKyungpook National UniversityDaeguKorea

Personalised recommendations