Abstract
The potential of recycled Poly(ethylene terephtalate) (PET) as a surface coating for steel corrosion protection, using a vinyl resin coating (PVC) as a control was studied. This investigation led us to develop a method to measure the adhesion strength of plastic coatings on steel under specific environmental conditions (temperature and UV exposure). All the results obtained showed that recycled PET presented very good adhesion on steel and that temperature and UV exposure induced only insignificant loss of adhesion. The results also showed that UV exposure induced a slight degradation of the PET.
Similar content being viewed by others
References
Weyers, R.E. and Cady, P.D.,ACI Journal, Proceedings V.81, No. 6, pp. 618–622, November–December 1984.
Clifton, J.R., Beeghly, H.F., and Mathey, R.G., Report No. FHWA-RD-74-18, Federal Highway Administration, Washington, D.C., p. 87, February 1974.
Clear, K.C. and Virmani, Y.P., Paper No. 114, Corrosion/83, Anaheim, Apr. 1983), National Association of Corrosion Engineers, p. 21, Houston, 1983.
Virmani, Y.P., Clear, K.C., and Pasko, T.L., V.5, “Calcium Nitrite Admixture or Epoxy-Coated Reinforcing Bars as Corrosion Protection Systems,” Report No. FHWA-RD-82-012, Federal Highway Administration, Washington, D.C., p. 71, September 1983.
Manjal, S.K., Report No. FHWA-MD-82-03, Maryland State Highway Administration, Brooklandville, p. 131, March 1981.
Hagen, M.G., Report No. FHWA-MN-RD-83-01, Minnesota Department of Transportation, St. Paul, p. 39, November 1982.
McKeel, W.T. Jr., HPR Study No. 79, Virginia Highway and Transportation Research Council, Charlottesville, p. 5, July 1984.
Savadogo, O., “Study on the Coating Process of Metallic Process Structures With Plastics,” Advance Report, March 1992.
Savadogo, O., ‘Study on the Coating Process of Metallic Process Structures With Plastics,” Advance Report, December 1992.
Tighiourd, B. and al., Report on the adherence of reinforced rebar with plastics in concrete, April 1994.
Savadogo, O and Lévesque, S., “Etude de al Performance de Revêtements Plastiques sur les Structures Métalliques,” CDT Report No. 1959, March 1994.
Chalker, P.R., Bull, S.J., and Rickerby, D.S., “A Review of the Methods for the Evaluation of Coating-Substrate Adhesion,”Materials Sci. Eng., A140, p. 583 (1991).
Steinmann P.A. and Hintermann, H.E., “A Review of the Mechanical Tests for Assessment of Thin-Film Adhesion,”J. Vacuum Sci. Tech., Vol. 7A, No. 3, p. 2267 (1989).
Goldberg, H.D., Cha, G.S., and Brown, R.B., “A Quantitative Adhesion Test for Thin Polymer Films on Silicon Substrates,”J. Applied Polym. Sci., Vol. 43, p. 1287 (1991).
Massingill, J.L., “Adhesion and Flexibility Contributions to the Performance of Epoxy Phosphate Ester Coatings,”Journal of Coatings Technology,63, No. 797, 47 (1991).
Yokoya, H. and Porter, R.S., “Polyester Adhesion to Chromium-Coated Steel for Poly(ethylene terephtalate) and an Isophtalate Copolymer,”J. Applied Polym. Sci., Vol. 44, p. 1679 (1992).
Lin, D.S., “The Adhesion of Metal Films to Glass and Magnesium Oxide in Tangential Shear,”J. Physics D: Applied Physics, Vol. 4, p. 1977 (1971).
Aravot, Y.M., Arcan, L., Arcan, M.E., and Albu-Yaron, A., “Adhesion of Lacquer to Phosphated Steel—A Shear Test Evaluation,”J. Materials Sci., Vol. 25, p. 3714 (1990).
Aravot, Y.M. and Albu-Yaron, A., “The Effects of Environmental Moisture on the Adhesion Toughness of Epoxy-Coated Phosphated Steels,”J. Materials Sci., Vol. 12, p. 1437 (1993).
Jindal, P.C., Quinto, D.T., and Wolfe, G.J., “Adhesion Measurements of Chemically Vapor Deposited and Physically Vapor Deposited Hard Coatings on WC-Co Substrates,”Thin Solid Films, Vol. 154, p. 361 (1987).
Ritter, J.E., Lardner, T.J., Rosenfeld, L., and Lin, M.R., “Measurement of Adhesion of Thin Polymer Coatings by Indentation,”J. Applied Physics, Vol. 66, No. 8, p. 3626 (1989).
Spengier, E., Margarit, I.C.P., and Mattos, O.R., “On the Relation Between Adherence of a Paint Film and Corrosion Protection,”Electrochemica Acta, Vol. 38, No. 14, p. 1999 (1993).
Skrovanek, D.J., “Fourier Transform Infrared Spectroscopic Studies of Coatings Defects,”Journal of Coatings Technology,61, No. 769, 31 (1989).
Oosterbroek, M., Lammers, R.J., and Van der Ven, L.G.J., “Crack Formation and Stress Development in an Organic Coating,”Journal of Coatings Technology,63, No. 797, 55 (1991).
Wu, Souheng, inPolymer Interfce and Adhesion, Ed., Marcel Dekker, New York and Basel, p. 510–517, 1982.
Kin, K.S. and Kin, J., “Elasto-Plastic Analysis of the Peel Test for Thin Film Adhesion,”J. Eng. Materials Tech., Vol. 110, p. 266–273 (1988).
Author information
Authors and Affiliations
Additional information
Pôle Technologique Henri Farman, Esplanade Roland Garros, BP 1029, 51686 Reims Cedex 2, France.
Département de Métallurgie et de Génie des Matériaux, C.P. 6079, Succ. A, Montréal, Que., Canada, H3C 3A7.
Rights and permissions
About this article
Cite this article
Bourgés, F., Savadogo, O. Development of a recycled polymer coating for steel corrosion protection: An adhesion study. Journal of Coatings Technology 70, 63–69 (1998). https://doi.org/10.1007/BF02697842
Issue Date:
DOI: https://doi.org/10.1007/BF02697842