Skip to main content
Log in

Untersuchungen über die Dickenschwankungen bei Holzfaserplatten

Studies on thickness variation in hardboard

  • Published:
Holz als Roh- und Werkstoff Aims and scope Submit manuscript

Zusammenfassung

Die Dickenschwankungen bei Holzfaserhartplatten, soweit sie durch den Preßvorgang bedingt sind, werden besprochen. Die Dicke der Platte hängt weitgehend von der Beschaffenheit der Preßplatte ab, in welcher das Faservlies gepreßt wird. So wurde beobachtet, daß Platten, die den obersten Etagen entstammen, im allgemeinen an ihren Enden dicker sind als in der Mitte, während solche, die aus unten gelegenen Etagen kommen, im Gegensatz dazu in der Mitte dicker sind. Diejenigen Platten dagegen, die in den mittleren Etagen gepreßt wurden, zeigten allgemein eine ziemlich gleichmäßige Dicke. Die Dickenabweichungen der aus den obersten Etagen stammenden Platten wurden als wesentlich höher festgestellt als die Abweichungen der aus den unteren oder mittleren Etagen kommenden Platten. Der Hauptanteil der Ausschußplatten mit zu großer Dicke stammt also aus den oberen Etagen, der Ausschuß durch zu dünne Platten aus den unteren Etagen. Nach der dritten Etage von unten wird die Wahrscheinlichkeit des Ausschusses wesentlich kleiner, nimmt jedoch nach der 19. Etage der insgesamt 20 Etagen umfassenden Hartplattenpresse wieder zu.

Summary

Variation in thickness in hardboard, as influenced by the pressing operation is discussed. Thickness of boards depends on the daylight which has pressed the pulp, thus whereas the boards obtained from the uppermost daylight are generally thicker at the ends than in the centre, those obtained from the lower daylights may be thicker at the centre. Pulp pressed in the central daylights gives fairly uniform products. The thickness variation arising in the upper daylights is substantially more than that in the lower or central daylights.

Majority of the rejects due to too thick boards results from the upper daylights, rejects due to too thin boards are mostly form the lower daylights. The probability of rejects due to out of tolerance boards falls rapidly after third daylight, but may show a slight rise after daylight 19 in a common 20 daylight hardboard super water heated press.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Schrifttum

  1. Kollmann, F.: Eigenschaftsstreuungen bei Holzfaserhartplatten. Holz als Roh- und Werkstoff Bd.6, (1957) S. 247/252.

    Google Scholar 

  2. Kumar, V. B., u. O. L. Johansen: Variation in Physical and Mechanical Properties of Quarter Iuch Pressed Boards. Norsk Skogindustri Bd.2 (1958) S. 47.

    Google Scholar 

  3. Stillinger, J. R., u. W. G. Coggan: Relationship of Moisture Content and Flexural Properties in 25 Commercial Hardboards. For. Prod. J. Bd.5 (1956) S. 179.

    Google Scholar 

  4. Kumar, V. B.: Variation in Physical and Mechanical Properties of Hardboards. Unveröffentlichte Arbeit, Nösted Bruk A. S. Drammen.

  5. Kumar, V. B., u. O. L. Johansen: Siehe [2] Teil 2. Veröffentlichung in Kürze.

  6. FAO: Third Conference on Wood Technology. Food and Agricultural Organization of the United Nations Paris 1955, S. 121.

  7. Kumar, V. B.: Non-Destructive Tests for Hardboard Quality Evaluation. Svenks Papperstidning Bd.15 (1958) S. 461.

    Google Scholar 

  8. Roald, B.: Unveröffentlichter Bericht in Papirindustriens Forskningsinstitutt, Oslo, 1958.

  9. Elieson, C. A.: Aktuellt om Wallboardpressen. Svensk Papp. Tidn. Bd.11 (1956) S. 402.

    Google Scholar 

  10. Keylwerth, R.: Statistische Qualitätskontrolle. Holz als Roh- und Werkstoff Bd.7 (1955) S. 268 bis 271.

    Google Scholar 

  11. Kumar, V. B.: Statistical Quality Control in Wood Industry, Part 1: Veneer Drier. Composite Wood Bd.2 (1956) S. 37.

    Google Scholar 

  12. Kumar, V. B.: Application of Statistical Quality Control to Cooling Process in Wood Fibre Insulation Board Industry. Norsk Skogindustri Bd.5 (1957) S. 193.

    Google Scholar 

  13. Kumar, V. B.: Statistical Quality Control Methods and their Application to Hardboard Industry. Norsk Skogindustri Bd.6 (1958) S. 204.

    Google Scholar 

  14. Kumar, V. B.: Application of Statistical Quality Control to Veneer Driers. Norsk Skogindustri Bd.5 (1957) S. 397.

    Google Scholar 

  15. Grant, E. L.: Statistical Quality Control, Second Edition. New York 1952: McGraw-Hill.

    Google Scholar 

  16. A. S. T. M.: Manual on Quality Control of Materials. Jan. 1951, S. 26.

  17. Papirindustriens Forskiningsinstitutt Oslo.

  18. Juran, J. M.: Quality Control Handbook, First Edition, S. 79. New York 1951: MacGraw-Hill.

    Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Rights and permissions

Reprints and permissions

About this article

Cite this article

Kumar, V.B. Untersuchungen über die Dickenschwankungen bei Holzfaserplatten. Holz als Roh-und Werkstoff 16, 371–377 (1958). https://doi.org/10.1007/BF02617855

Download citation

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF02617855

Navigation