Zusammenfassung
Holzfaserplatten mit 3 mm Dicke wurden bei einem Verhätnis von Stützweite zu Probendicke (=L/h) zwischen 10 und 45 durch Biegefestigkeitsprüfungen untersucht. Es wurde festgestellt, daß mit wachsendem VerhältnisL/h im Bereich von 10 bis 25 die Biegefestigkeit zunimmt und anschließend konstant bleibt oder wieder absinkt. Ebenso wurde festgestellt, daß mit zunehmender Probenbreite die Biegefestigkeit im BereichL/h von 10 bis 25 abnimmt, während von 25 bis 45 keine eindeutige Tendenz zu erkennen ist. Es konnte ferner beobachtet werden, daß bei 75 mm Probenbreite nach Erreichen des Maximums beiL/h=25 die Biegefestigkeit im weiteren Verlauf konstant bleibt. Es wurde deutlich, daß bei niedrigerenL/h-Werten die Breite einen größeren Einfluß ausübt. während sie bei höheren Werten von geringerer Bedeutung ist.
Summary
Hard-boards of 3 mm thickness were tested under varying span-depth ratio ranging from 10 to 45. It has been observed that as the ratio increases, the modulus of rupture in the interval 10 to 25 increases and then it is either constant or falls off. It is also observed that by increasing the width of the specimens, the modulus of rupture in the interval of span-depth ratios 10 to 25 is decreasing while in the interval of 25 to 45 no definite trend is indicative. It is further observed that for the width of 75 mm, after having reached the maximum at the span-depth ratio of 25, the moduls of rupture tends to remain constant for higher values. However, it has been evident that for smaller span-depth ratios width has a greater influence and for higher span-depth ratios width shows no such noteworthy difference. *** DIRECT SUPPORT *** A02R4275 00002
Schrifttum
Bach, C., u. R. Baumann: Elastizität und Festigkeit, 9. Aufl. Berlin 1924, Springer.
F.A.O.: Fibre Board and Particle Board. Report of an International Consultation on Insulation Board, Hardboard and Particle Board, sponsored jointly by the F.A.O. of the United Nations and the Economic Commission for Europe. Geneva, January 21 to February 4, 1957.
I.S.I.: Specification for Fibre Hard-Boards. IS: 1658–1960/IS: 1658–1966.
I.S.I.: Methods of Test for Wood Particle Boards and Boards from other Lignocellulosic Materials. IS: 2380–1963.
I.S.O.: Method of Determination of Bending Strength of Fibre Building Boards. Draft ISO Recommendation No. 842, Feb. 1965.
Kollmann, F.: Eigenschaften, Prüfung und Klassifizierung von Holzfaser- und Holzspanplatten. Svensk Papperstidning Bd.52 (1949) No. 10, S. 251/267.
Kollmann, F. u. A. Dosondil: Holzfaserplatten. Ihre Eigenschaften und Prüfung, mit besonderer Berücksichtigung der Dauer. festigkeit Forschungsheft 426. „Forschung auf dem Gebiete des Ingenieurwesens”, B. Bd.16 (1949) Sept.
Sekhar, A. C., u. B. S. Rawat. Influence of Size, Shape and Notches in Test Specimens in Timber J. Ind. Engg. Vol. 1956, No. 12.
—, u. S. S. Rajput: Some Observations on the Effect of Size and Shape of Test Specimens and Direction of Load on some Mechanical Properties of Wood. Materialprüf, Bd.7 (1965) Nr. 9, S. 340/342.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Sekhar, A.C., Khurana, R.L. & Singh, M.M. Einfluß des Verhältnisses von Stützweite zu Probendicke auf die Biegefestigkeit von Faserplatten. Holz als Roh-und Werkstoff 27, 110–112 (1969). https://doi.org/10.1007/BF02608314
Issue Date:
DOI: https://doi.org/10.1007/BF02608314