# A Methodology for Inverse Determination of Stress-strain Curves Based on Spherical Indentation

- 118 Downloads

## Abstract

Instrumented indentation testing is widely used for the mechanical characterization of materials and phases. Among important mechanical parameters such as hardness and Young’s modulus the determination of yield stress and hardening behavior of metallic materials calculated from indentation results is a particular topical subject. This paper presents a methodology which allows for the reconstruction of the stress-strain curve from a single load-displacement curve measured by a spherical indenter. The method is based on the depth-dependent strain field induced by a spherical indenter. The loading part of the curve is discretised in single tuples of indentation depth and force. Since the mean strain induced by the spherical indenter is dependent on indentation depth, every depth can be assigned to a mean uniaxial strain value. The force is then used to calculate the associated uniaxial stress. The method was exemplarily applied to the carbon steel C45 in different heat treatment conditions. It could be shown that after a calibration procedure the stress-strain curves of the carbon steel can be calculated without the requirement of assuming a mathematical description of the curve (e.g. power-law material behavior). The method and its framework can easily be expanded and adjusted in order to be used as an easy and quick method for inverse determination of material parameters.

## Keywords

Indentation Stress-strain curve Plastic properties Inverse analysis## References

- 1.Oliver W-C, Pharr G-M (1992) An improved technique for determination hardness and elastic-modulus using load and displacement. J Mater Res 7:1564–1583CrossRefGoogle Scholar
- 2.Taljat B, Zacharia T, Kosel F (1998) New analytical procedure to determine stress-strain curve from spherical indentation data. Int J Solids Struct 35:4411–4426CrossRefGoogle Scholar
- 3.Huber N, Tsakmakis C (1999) Determination of constitutive properties from spherical indentation data using neural networks. Part ii: plasticity with nonlinear isotropic and kinematic hardening. J Mech Phys Solids 47:1589–1607CrossRefGoogle Scholar
- 4.Huber N, Tsakmakis C (1999) Determination of constitutive properties from spherical indentation data using neural networks. Part I: the case of pure kinematic hardening in plasticity laws. J Mech Phys Solids 47:1569–1588CrossRefGoogle Scholar
- 5.Cao Y -P, Lu J (2004) A new method to extract the plastic properties of metal materials from an instrumented indentation loading curve. Acta Mater 52:4023–4032CrossRefGoogle Scholar
- 6.Beghini M, Bertini L, Fontanari V (2006) Evaluation of the stress-strain curve of metallic materials by spherical indentation. Int J Solids Struct 43:2411–2459Google Scholar
- 7.Collin J -M, Mauvoisin G, Pilvin P (2010) Materials characterization by instrumented indentation using two different approaches. Mater Des 31:636–640CrossRefGoogle Scholar
- 8.Hasanov A, Muradoglu Z (2012) Fast inversion algorithm for identification of elastoplastic properties of power hardening materials. Int J Non-Linear Mech 47:526–536CrossRefGoogle Scholar
- 9.Patel D -K, Kalidindi S-R (2016) Correlation of spherical nanoindentation stress-strain curves to simple compression stress-strain curves for elastic plastic isotropic materials using finite element models. Acta Materialia 112:295–302CrossRefGoogle Scholar
- 10.Chen W -C, Li M, Zhang T, Cheng Y -T, Cheng C -M (2007) Influence of indenter tip roundness behavior in nanoindentation. Mater Sci Eng A 445-446:323–327CrossRefGoogle Scholar
- 11.Liu L, Ogasawara N, Chiba N, Chen X (2009) Can indentation technique measure unique elastoplastic properties?. J Mater Res 24:784–800CrossRefGoogle Scholar
- 12.Tabor D (1948) A simple theory of static and dynamic hardness. Proc R Soc London Series Math Phys Sci 192:247–274CrossRefGoogle Scholar
- 13.Tabor D (2000) The hardness of metals. Oxford University Press, OxfordGoogle Scholar
- 14.Cao Y -P, Qian X, Huber H (2007) Spherical indentation into elastoplastic materials: Indentation-response based definition of the representative strain. Mater Sci Eng A 454-455:1–13CrossRefGoogle Scholar
- 15.Donohue B -R, Ambrus A, Kalidindi S-R (2012) Critical evaluation of the indentation data analyses methods for the extraction of isotropic uniaxial mechanical properties using finite element models. Acta Metallurgica 60:3943–3952Google Scholar
- 16.Pöhl F, Huth S, Theisen W (2014) Indentation of self-similar indenters: An FEM-assisted energy-based analysis. J Mech Phys Solids 66:32–41CrossRefGoogle Scholar
- 17.Field J -S, Swain M -V (1993) A simple predictive model for spherical indentation. J Mater Res 8:297–306CrossRefGoogle Scholar
- 18.Lee J -H, Kim T, Lee H (2010) A study on robust indentation techniques to evaluate elastic-plastic properties of metals. Int J Solids Struct 47:647–664CrossRefGoogle Scholar
- 19.Ahn J -H, Kwon D (2001) Derivation of plastic stress-strain relationship from ball indentations. J Mater Res 16:3170–3178CrossRefGoogle Scholar
- 20.N’Jock M -Y, Chicot D, Decoopman X, Lesage J, Ndjaka J -M, Pertuz A (2013) Mechanical tensile properties by spherical macroindentation using an indentation strain-hardening. Int J Mech Sci 75:257–264CrossRefGoogle Scholar
- 21.Swaddiwudhipong S, Tho K -K, Liu Z -S, Zeng K (2005) Material characterization based on dual indenters. Int J Solids Struct 42:69–83CrossRefGoogle Scholar
- 22.Pharr G -M, Herbert E -G, Gao Y (2010) The indentation size effect: A critical examination of experimental observations and mechanistic interpretations. Annu Rev Mater Res 40:271–292CrossRefGoogle Scholar
- 23.Swadener J G, George E -P, Pharr G -M (2002) The correlation of indentation size effect measured with indenters of various shapes. J Mech Phys Solids 50:681–694CrossRefGoogle Scholar
- 24.Qu S, Huang Y, Pharr G -M, Hwang K -C (2006) The indentation size effect in the spherical indentation of iridium: A study via the conventional theory of mechanism-based strain gradient plasticity. Int J Plast 22:1265–1286CrossRefGoogle Scholar
- 25.Niederhofer P, Pöhl F, Geenen K, Huth S, Theisen W (2016) Influence of crystallographic orientation on cavitation erosion resistance of high interstitial CrMnCN austenitic stainless steels. Tribol Int 95:66–75CrossRefGoogle Scholar