Influence of Shear Stress on Erosion–Corrosion of Stainless Steels in Simulated Mine Water

  • A. K. Moloto
  • M. H. E. Seshweni
  • N. J. Mathe
  • B. A. Obadele
  • S. Aribo
  • P. A. Olubambi
  • O. O. Ige
Article
  • 25 Downloads

Abstract

This study provides information on the performance of three stainless steels at various shear stresses and presence of silica sand particles in simulated mine water. The materials employed were two duplex stainless steels (UNS S32205 and UNS S32750) and one austenitic stainless steel (UNS 30403). The rotating cylinder electrode system produced shear stresses to evaluate the flow-induced and erosion–corrosion tests by open-circuit potential and potentiodynamic polarization techniques. Hardness tests were used to examine the performance of the degraded samples, and scanning electron microscopy was used to characterize the surface morphology. UNS S32750 displayed nobler OCP compared with UNS S32205 with austenitic steel having the least potential irrespective of the shear stresses and with/without silica sand. Work hardening of the duplex stainless steels promoted variable behavior in the hardness results. The current density results revealed that UNS S32705 had the best corrosion performance in the studied environments. The SEM images showed plastic deformation, material dissolution and pitting corrosion as the shear stress increased and on the introduction of silica sand.

Keywords

Erosion–corrosion Rotating cylinder electrode Stainless steel Simulated mine water 

Notes

Compliance with Ethical Standards

Conflict of interest

On behalf of all authors, the corresponding author states that there is no conflict of interest with the article.

References

  1. 1.
    Cortie MB, McEwan JJ, Enright DP (1996) Materials selection in the mining industry: old issues and new challenges. J South Afr Inst Min Metall 96(4):145–157Google Scholar
  2. 2.
    Lindgren M, Suihkonen R, Vuorinen J (2015) Erosive wear of various stainless steel grades used as impeller blade materials in high temperature aqueous slurry. Wear 328–329:391–400CrossRefGoogle Scholar
  3. 3.
    Lindgren M, Siljander S, Suihkonen R, Pohjanne P, Vuorinen P (2016) Erosion–corrosion resistance of various stainless steel grades in high-temperature sulfuric acid solution. Wear 364–365:10–21CrossRefGoogle Scholar
  4. 4.
    Burson-Thomas CB, Wood RJK (2017) Developments in erosion–corrosion over the past 10 years. J Bio Tribo Corros 3:14.  https://doi.org/10.1007/s40735-017-0073-4 CrossRefGoogle Scholar
  5. 5.
    Aribo S, Barker R, Hu X, Neville A (2013) Erosion–corrosion behaviour of lean duplex stainless steels in 3.5% NaCl solution. Wear 302:1602–1608CrossRefGoogle Scholar
  6. 6.
    Giourntas L, Hodgkiess T, Galloway AM (2015) Comparative study of erosion–corrosion performance on a range of stainless steels. Wear 332–333:1051–1058CrossRefGoogle Scholar
  7. 7.
    Zhao Y, Zhou F, Yao J, Dong S, Li N (2015) Erosion–corrosion behavior and corrosion resistance of AISI 316 stainless steel in flow jet impingement. Wear 328–329:464–474CrossRefGoogle Scholar
  8. 8.
    Silverman DC (1984) Rotating cylinder electrode for velocity sensitivity testing. Corrosion 40(5):220–226CrossRefGoogle Scholar
  9. 9.
    Effird KD, Wright EJ, Boros JA, Hailey TG (1993) Correlation of steel corrosion in pipe flow with jet impingement and rotating cylinder tests. Corrosion 49:992–1003CrossRefGoogle Scholar
  10. 10.
    Walsh FC, Kear G, Nahle AH, Wharton JA, Arena LF (2017) The rotating cylinder electrode for studies of corrosion engineering and protection of metals—an illustrated review. Corros Sci 123:1–20CrossRefGoogle Scholar
  11. 11.
    Ige OO, Barker R, Hu X, Umoru LE, Neville A (2013) Assessing the influence of shear stress and particle impingement on inhibitor efficiency through the application of in situ electrochemistry in a CO2-saturated environment. Wear 304(1–2):49–59CrossRefGoogle Scholar
  12. 12.
    Hango SI, Chown LH, van der Merwe JW, Kavishe FPL, Cornish LA (2014) Corrosion of selected hard facing materials exposed to mine water. Int Sci Technol J Namibia 4:90–105Google Scholar
  13. 13.
    ASTM E3-11 (2011) Standard guide for preparation of metallographic specimens. ASTM International, West Conshohocken, PA. www.astm.org
  14. 14.
    Ige OO, Aribo S, Obadele BA, Langa T, Olubambi PA (2017) Erosion–corrosion characteristics of spark plasma sintered pure nickel in simulated mine water. Tribol Int 109:441–446CrossRefGoogle Scholar
  15. 15.
    Lethbane ML, Olubambi PA, Chikwanda HK (2015) Corrosion behaviour of sintered Ti–Ni–Cu–Nb in 0.9% NaCl environment. J Mater Res Technol 4(4):367–376CrossRefGoogle Scholar
  16. 16.
    Song G, Atrens A, Wu X, Zhang B (1998) Corrosion behaviour of AZ21 AZ501 and AZ91 in sodium chloride. Corros Sci 40(10):1769–1791CrossRefGoogle Scholar
  17. 17.
    Yuan Q-L, Stack MM (2002) Effect of preferential dissolution on erosion–corrosion for chromium steel in alkali slurry. Trans Nonferr Metals Soc China 12(5):931–935Google Scholar
  18. 18.
    Lu BT, Luo JL, Mohammad F, Wang K, Wan XM (2008) Correlation between repassivation kinetics and corrosion rate over a passive surface in flowing slurry. Electrochimita Acta 53:7022–7031CrossRefGoogle Scholar
  19. 19.
    Belfrouh A, Masson C, Vouagner D, De Becdelievre AM, Prakash NS, Audouard JP (1996) The cumulative effect of alloying elements N, W, Mo and Cu on the corrosion behaviour of 17Cr-13Ni stainless steel in 2 N H2SO4. Corros Sci 38(10):1639–1648CrossRefGoogle Scholar
  20. 20.
    Kim JS, Xiang PJ, Kim KY (2005) Effect of tungsten and nickel addition on the repassivation behaviour of stainless steel. Corrosion 61(2):174–183CrossRefGoogle Scholar
  21. 21.
    Kim JS, Kwon HS (1999) Effects of tungsten on corrosion and kinetics of sigma phase formation of 25% chromium duplex stainless steels. Corrosion 55(5):512–521CrossRefGoogle Scholar
  22. 22.
    Haugan EB, Naess M, Rodriguez CT, Johnsen R, Iannuzzi M (2017) Effect of Tungsten on the pitting and crevice corrosion resistance of type 25Cr super duplex stainless steels. Corrosion 73(1):53–67CrossRefGoogle Scholar
  23. 23.
    Park HJ, Lee HW (2014) Effect of alloyed Mo and W on the corrosion characteristics of super duplex stainless steel weld. Int J Electrochem Sci 9:6687–6698Google Scholar

Copyright information

© Springer International Publishing AG, part of Springer Nature 2018

Authors and Affiliations

  • A. K. Moloto
    • 1
  • M. H. E. Seshweni
    • 1
  • N. J. Mathe
    • 1
  • B. A. Obadele
    • 1
  • S. Aribo
    • 1
    • 2
  • P. A. Olubambi
    • 1
  • O. O. Ige
    • 1
    • 3
  1. 1.Center for NanoEngineering and Tribocorrosion, School of Mining, Metallurgy and Chemical EngineeringUniversity of JohannesburgJohannesburgSouth Africa
  2. 2.Department of Metallurgical, and Materials EngineeringFederal University of TechnologyAkureNigeria
  3. 3.Department of Materials Science and EngineeringObafemi Awolowo UniversityIle-IfeNigeria

Personalised recommendations