Advertisement

Numerical simulation of the influence of fluid motion in mushy zone during micro-EDM on the crater surface profile of Inconel 718 alloy

  • Deepak G. DilipEmail author
  • S. P. Ananthan
  • Satyananda Panda
  • Jose Mathew
Technical Paper
  • 19 Downloads

Abstract

The micro-EDM, due to its ability to machine any electrically conductive material, has been one of the preferred manufacturing methodologies for machining difficult to machine materials. The micro-EDM is a thermal energy-based material removal process where the material removal occurs by spark erosion. In majority of the modeling associated with micro-EDM, the effect of the fluid motion in the liquid and mushy phase of the workpiece alloy is not considered. This paper aims at numerically simulating the crater surface profile formed on Inconel 718 incorporating the effects of material movement in the mushy zone using micro-EDM. Navier–Stokes equations were used as the governing equations. Temperature-dependent specific heat, thermal conductivity, density and viscosity were incorporated, in three ranges, i.e., solid (\({T}<1523\hbox { K}\)), liquid (\(T>1609\hbox { K}\)) and mushy (\(1523\hbox { K}<{T}<1609\hbox { K}\)). The mushy zone properties were calculated using enthalpy porosity method, and the properties were updated after each iteration. Specific boundary conditions like Gaussian distributed heat flux on the top surface, fixed percentage of heat to the anode and Marangoni stress on the top surface of the workpiece were applied. The simulations were performed using CFD package ANSYS 15.0 FLUENT for three distinct voltages 100, 125 and 150 V, keeping capacitance constant at \(0.4\,\upmu \hbox {F}\). User-defined functions were written in C language to incorporate the temperature-dependent properties and the boundary conditions. These simulated results were compared with the experimental values at same input condition, and the maximum calculated deviation in crater profile prediction was less than 14%.

Keywords

Micro-EDM Inconel 718 Mushy zone Navier–Stokes equations Crater profile 3D profilometer 

Notes

Acknowledgements

Authors would like to sincerely thank Department of Science and Technology (DST), Govt. of India, and Centre for Precision Measurements and Nanomechanical Testing, Department of Mechanical Engineering, National Institute of Technology Calicut, for providing support to carry out this work under the scheme Fund for Improvement of Science and Technology (No. SR/FST/ETI-388/2015).

References

  1. 1.
    Meshram DB, Puri YM (2017) Review of research work in die sinking EDM for machining curved hole. J Braz Soc Mech Sci Eng 39(7):2593–2605CrossRefGoogle Scholar
  2. 2.
    Masuzawa T (2000) State of the art of micromachining. CIRP Ann 49(2):473–488CrossRefGoogle Scholar
  3. 3.
    Dhanik S, Joshi SS (2005) Modeling of a single resistance capacitance pulse discharge in micro-electro discharge machining. J Manuf Sci Eng 127(4):759–767CrossRefGoogle Scholar
  4. 4.
    Jilani ST, Pandey PC (1982) Analysis and modelling of EDM parameters. Precis Eng 4(4):215–221CrossRefGoogle Scholar
  5. 5.
    Van Dijck FS, Dutre WL (1974) Heat conduction model for the calculation of the volume of molten metal in electric discharges [discharge machining]. J Phys D Appl Phys 7(6):899–910CrossRefGoogle Scholar
  6. 6.
    DiBitonto DD, Eubank PT, Patel MR, Barrufet MA (1989) Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model. J Appl Phys 66(9):4095–4103CrossRefGoogle Scholar
  7. 7.
    Yeo SH, Kurnia W, Tan PC (2008) Critical assessment and numerical comparison of electro-thermal models in EDM. J Mater Process Technol 203:241–251CrossRefGoogle Scholar
  8. 8.
    Joshi SN, Pande SS (2010) Thermo-physical modeling of die-sinking EDM process. J Manuf Process 12(1):45–56CrossRefGoogle Scholar
  9. 9.
    Patel MR, Barrufet MA, Eubank PT, DiBitonto DD (1989) Theoretical models of the electrical discharge machining process- II: the anode erosion model. J App Phys 66:4104–4111CrossRefGoogle Scholar
  10. 10.
    Yeo SH, Kurnia W, Tan PC (2007) Electro-thermal modelling of anode and cathode in micro-EDM. J Phys D Appl Phys 40(8):2513–2521CrossRefGoogle Scholar
  11. 11.
    Allen P, Chen X (2007) Process simulation of micro electro-discharge machining on molybdenum. J Mater Process Technol 186:346–355CrossRefGoogle Scholar
  12. 12.
    Murali MS, Yeo SH (2005) Process simulation and residual stress estimation of micro- electro discharge machining using finite element method. Jpn J Appl Phys 44(7A):5254–5263CrossRefGoogle Scholar
  13. 13.
    Shabgard M, Ahmadi R, Seyedzavvar M, Oliaei SNB (2013) Mathematical and numerical modeling of the effect of input-parameters on the flushing efficiency of plasma channel in EDM process. Int J Mach Tools Manuf 65:79–87CrossRefGoogle Scholar
  14. 14.
    Zhang Y, Liu Y, Shen Y et al (2013) A new method of investigation the characteristic of the heat flux of EDM plasma. Proc CIRP 6:450–455CrossRefGoogle Scholar
  15. 15.
    Singh H (2012) Experimental study of distribution of energy during EDM process for utilization in thermal models. Int J Heat Mass Transf 55:5053–5064CrossRefGoogle Scholar
  16. 16.
    Tao J, Ni J, Shih AJ (2012) Modeling of the anode crater formation in electrical discharge machining. J Manuf Sci Eng 147:011002-1–011002-11Google Scholar
  17. 17.
    Mujumdar SS, Curreli D, Kapoor SG, Ruzic D (2015) Modeling of melt-pool formation and material removal in micro-electrodischarge machining. ASME J Manuf Sci Eng 137(3):031007-1–031007-9CrossRefGoogle Scholar
  18. 18.
    Dilip DG, John G, Panda S, Mathew J (2016) Numerical modeling of micro-EDM process using finite volume method. In: Ahuja BB, Basu SK, Rajiv B (eds) 6th international and 27th all India manufacturing technology, design and research conference (AIMTDR 2016), College of Engineering Pune, Pune, India, 16–18 December 2016, pp 1556–1560Google Scholar
  19. 19.
    Versteeg HK, Malalasekera W (2007) An introduction to computational fluid dynamics the finite volume method, 2nd edn. PHI, HarlowGoogle Scholar
  20. 20.
    Patankar VS (1980) Numerical heat transfer and fluid flow, 1st edn. CRC Press, Boca RatonzbMATHGoogle Scholar
  21. 21.
    Voller RV, Prakash C (1987) A Fixed grid numerical modeling methodology for convection-diffusion mushy region phase-change problems. Int J Heat Mass Transf 30(8):1709–1719CrossRefGoogle Scholar
  22. 22.
    Kuriachen B, Varghese A, Somashekar KP, Mathew J (2014) Three-dimensional numerical simulation of micro electric discharge machining of Ti–6Al–4V. Int J Adv Manuf Technol 79(1):147–160Google Scholar
  23. 23.
    Somashekhar KP, Panda S, Mathew J, Ramachandran N (2015) Numerical simulation of micro-EDM model with multi spark. Int J Adv Manuf Technol 76:83–90CrossRefGoogle Scholar
  24. 24.
    Shao B, (2015) Modeling and simulation of micro electrical discharge machining process. Dissertation, The Graduate College at University of NebraskaGoogle Scholar
  25. 25.
    Saunders N, Guo Z, Li X, Miodownik AP, Schillé J (2004) Modelling the material properties and behaviour of Ni-based superalloys. In: Green KA, Pollock TM, Harada H, Howson TE, Reed RC, Schirra JJ, Walston S (eds) Superalloys 2004 - Proceedings of the tenth international symposium on superalloys, Champion PA, United States, 19–23 September 2004, pp 849–858Google Scholar
  26. 26.
    Romano J, Ladani L, Sadowski M (2016) Laser additive melting and solidification of Inconel 718: finite element simulation and experiment. Min Met Mat Soc 68(3):967–977CrossRefGoogle Scholar
  27. 27.
    Mills CK (2002) Recommended values of thermophysical properties for selected commercial alloys, 1st edn. Woodhead Publishing Limited, CambridgeCrossRefGoogle Scholar
  28. 28.
    Ananthan SP, Dilip DG, Panda S, Mathew J (2017) Numerical simulation and experimental investigation of the crater surface profile formed during micro EDM on Inconel 718. In: Babu NR, Samuel GL (eds) 10th international conference on precision, meso, micro and nano engineering, IIT Madras, Chennai, India, 7–9 December 2017, Paper no 425, pp 243–246Google Scholar
  29. 29.
    Fluent 6.3 Users Guide (2006) Fluent IncGoogle Scholar

Copyright information

© The Brazilian Society of Mechanical Sciences and Engineering 2019

Authors and Affiliations

  • Deepak G. Dilip
    • 1
    Email author
  • S. P. Ananthan
    • 1
  • Satyananda Panda
    • 2
  • Jose Mathew
    • 1
  1. 1.Department of Mechanical EngineeringNational Institute of Technology CalicutKozhikodeIndia
  2. 2.Department of MathematicsNational Institute of Technology CalicutKozhikodeIndia

Personalised recommendations