Assessment of wood utility poles’ deterioration through natural frequency measurements
- 43 Downloads
Abstract
Utility poles in a power distribution line are usually made of prestressed concrete, reinforced concrete or wood. In Latin America, given the abundance of different species of wood suitable for structural purposes, the latter material is more commonly used. The durability of wood in structures exposed to meteorological agents is usually an issue, especially when these have a critical role in the operation of industries or when the structures provide a service to society. For this reason, it is convenient to develop simple techniques that allow the assessment of the damage during their service life. In this paper, results obtained experimentally are contrasted with the outcomes of finite element models, taking deterministic property values of the material and simulating the same load state of the test. The correlation between the degree deterioration of wood poles and their dynamic behavior taking into account defects such as cracks, knots and others, was evaluated. The wood used in the experiments is Eucalyptus grandis, a species that is widely cultivated in South and Central America and particularly, found in the northeastern part of Argentina. The experimental work has been carried out in laboratory using real poles with different degrees of damage and deterioration, that were provided by the EDES, the electricity company that provides service in the Province of Buenos Aires, Argentina.
Keywords
Wood poles Wood damage FEM Experimental mechanics Structural dynamicsNotes
Acknowledgements
The authors acknowledge the financial support of the Department of Engineering, the SGCyT-Universidad Nacional del Sur, CIC-Bs.As., ANPCyT and CONICET, all Argentinian agencies.
References
- 1.ASTM D 143-94 (2007) Standard test methods for small clear specimens of timber. West Conshohoken.Google Scholar
- 2.ASTM D 198 (2002) Standard test methods of static test of lumber in structural sizes. West Conshohoken.Google Scholar
- 3.ASTM D 1036 (2005) Standard test methods of static test of wood poles. West Conshohoken.Google Scholar
- 4.Piter J, Zerbino R, Blaß H (2004) Visual strength grading of Argentinean eucalyptus grandis. Holz als Roh-und Werkst 62(1):1–8CrossRefGoogle Scholar
- 5.García DA, Rosales MB (2017) Deflections in sawn timber beams with stochastic properties. Eur J Wood and Wood Prod 75(5):683–699CrossRefGoogle Scholar
- 6.García DA, Sampaio R, Rosales MB (2015) Vibrational problems of timber beams with knots considering uncertainties. J Braz Soc Mech Sci Eng 38:1–13Google Scholar
- 7.Torrán E, Zitto S, Cotrina A, Piter JC (2009) Bending strength and stiffness of poles of Argentinean eucalyptus grandis. Maderas. Ciencia y Tecnología 11(1):71–84CrossRefGoogle Scholar
- 8.Kurz JH (2015) Monitoring of timber structures.Google Scholar
- 9.Yu Y, Li J, Yan N, Dackermann U, Samali B (2016) Load capacity prediction of in-service timber utility poles considering wind load. J Civil Struct Health Monit 6(3):385–394CrossRefGoogle Scholar
- 10.Shafieezadeh A, Onyewuchi UP, Begovic MM, DesRoches R (2014) Age-dependent fragility models of utility wood poles in power distribution networks against extreme wind hazards. IEEE Trans Power Deliv 29(1):131–139CrossRefGoogle Scholar
- 11.ANSI-05.1 (2002) American national Standard for wood poles—Specifications and dimensions. Washintong.Google Scholar
- 12.Vernier Software and Technology (2010) “LabQuest TM.” https://www.vernier.com/products/interfaces/.
- 13.IRAM 9529 (2005) Wood poles static flexion test methods (Spanish). Buenos Aires.Google Scholar
- 14.ISO 3130:1975 (1975) Wood—determination of moisture content for physical and mechanical test. Geneva.Google Scholar
- 15.ISO 3131:1975 (1975) Wood—Determination of density for physical and mechanical tests.Google Scholar
- 16.FlexPDE, PDE (2017) Solutions inc.. http://www.pdesolutions.com.
- 17.MathWorks, Inc. MATLAB (2011) Matlab 2011a.Google Scholar
- 18.CIRSOC 601 (2011) Proyecto de Reglamento Argentino de Estructuras de Madera (Spanish).Google Scholar
- 19.Conway H, Becker E, Dubil J (1964) Vibration frequencies of tapered bars and circular plates. J Appl Mech 31(2):329–331CrossRefzbMATHGoogle Scholar