Advertisement

MAPAN

pp 1–6 | Cite as

Investigation of 1 GPa Controlled Clearance Piston Gauge Using Finite Element Analysis

  • Rudi Anggoro Samodro
  • In-Mook ChoiEmail author
  • Sam-Yong Woo
Original Paper

Abstract

A one GPa controlled clearance piston gauge used as a high pressure standard at KRISS was investigated. In establishing the high pressure standard, the distortion coefficient is one of the most important parameters, but it is not easy to determine. The conventional analysis using a Heydemann–Welch model has a problem when determining a stall pressure, because of the nonlinear characteristic of fall rates with respect to pressure. Some metrological characteristics, such as the distortion coefficient of the piston–cylinder assembly in free deformation (FD) mode and the jacket distortion coefficient and stall pressure in controlled clearance (CC) mode, were investigated using a finite element analysis (FEA). In particular, it was determined that the relation of cubic fall rate to jacket pressure becomes nonlinear above 600 MPa. The FEA results were verified by comparison with a 500 MPa pressure standard and a fall rate measurement of 1 GPa. The most important parameter, the distortion coefficient in the FD and CC mode, was determined to be (7.59 ± 0.24) × 10−7 MPa−1 and (3.35 ± 0.39) × 10−7 MPa−1, respectively. A zero-distortion coefficient was obtained in the FEA when around 17% of the applied pressure was used as the jacket pressure. This value was similar to the experimentally determined result of around 20%.

Keywords

Finite element analysis Piston gauge Distortion coefficient Fall rate Heydemann–Welch model 

Notes

References

  1. [1]
    R.S. Dadson, S.L. Lewis and G.N Peggs, The pressure balance theory and practice, National Physical Laboratory, HMSO, Delhi, 1982, pp. 1–9.Google Scholar
  2. [2]
    S.Y. Woo, Y.J. Lee, I.M. Choi, B.S. Kim and H.H. Shin, Effects of the O-ring used for sealing in high pressure balance on measurements of pressure, J. Meas. Sci. Technol. 13 (2002) 1353-1358.ADSCrossRefGoogle Scholar
  3. [3]
    S. Dogra, S. Yadav, A.K. Bandyopadhyay, Computer simulation of a 1.0 GPa piston–cylinder assembly using finite element analysis (FEA), Measurement, 43 (2010) 1345-1354.CrossRefGoogle Scholar
  4. [4]
    W. Sabuga, G. Molinar, G. Buonanno, T. Eswald, J.C. Legras and L. Yagmur, Finite element method used for calculation of the distortion coefficient and associated uncertainty of a PTB 1 GPa pressure balance—EUROMET project 463, J. Metrol., 43 (8) (2006) 311-325.ADSCrossRefGoogle Scholar
  5. [5]
    G. Molinar, W. Sabuga, G. Robinson and J.C. Legras, Comparison of methods for calculating distortion in pressure balances up to 400 MPa—EUROMET project #256, J. Metrol., 35 (1998) 739.ADSCrossRefGoogle Scholar
  6. [6]
    W. Sabuga, T. Priruenrom, G.M.M. Beciet, G. Giovinco, T. Rabault, P. Wongthep, D. Prazak, FEA calculation of pressure distortion coefficients of gas-operated pressure balances—EURAMET project 1039, Measurement, 45 (2012), 2462-2468.CrossRefGoogle Scholar
  7. [7]
    P. Wongthep, T. Rabault, R. Noguera and C. Sarraf, A new model of fluid flow to determine pressure balance characteristics, Metrologia, 50 (2013) 153-157.ADSCrossRefGoogle Scholar
  8. [8]
    R.A. Samodro, I.M. Choi and S.Y. Woo, A study on characteristics of 1 GPa controlled clearance piston gauge using finite element method, Proceeding of XX IMEKO World Congress, Busan, Republic of Korea, 2012, pp. 1658-1661.Google Scholar
  9. [9]
    H. Kajigawa, K. Ide and T. Kobata, Methods for altering deformational characteristics of controlled clearance piston–cylinders, Measurement, 44 (2011) 359-364.CrossRefGoogle Scholar
  10. [10]
    D.A. Olson, S.A. Gelany, A.A. Eltawil, Use of a higher order Heydemann–Welch model to characterize a controlled clearance piston gauge, Measurement, 15 (2011) 2469-2471.Google Scholar
  11. [11]
    R.A. Samodro, Characterization of 1 GPa controlled clearance piston gauge for high pressure standard using finite element method, Master Degree Thesis, (2012) pp. 26-28.Google Scholar

Copyright information

© Metrology Society of India 2020

Authors and Affiliations

  1. 1.University of Science and Technology (UST)DaejeonRepublic of Korea
  2. 2.Korea Research Institute of Standards and Science (KRISS)DaejeonRepublic of Korea
  3. 3.National Standardization Agency of Indonesia (BSN)Tangerang SelatanIndonesia

Personalised recommendations