Advertisement

Silicon

pp 1–9 | Cite as

Numerical Simulation on Design of Temperature Control for Side Heater in Directional Solidification System of Multi-Crystalline Silicon

  • Botao Song
  • Yufeng Luo
  • Senlin Rao
  • Fayun ZhangEmail author
  • Yun Hu
Original Paper
  • 18 Downloads

Abstract

In this paper, the transient numerical simulation was used to study the effects of temperature variation in three ways (the open downward parabola, the straight line and the open upward parabola) of side heater in multi-crystalline silicon directional solidification system during solidification period. The melt-crystal (m/c) interface, thermal field and thermal stress during directional solidification of polysilicon have been simulated. The results show that in the process of solidification, compared with the open downward parabola and straight line temperature variation, the temperature change of the side heater depends on the open upward parabola can better control the horizontal and vertical temperature difference in polysilicon, making the deflection of m/c interfaces smaller. Smaller thermal stress distribution can be obtained from the middle stage to the end of solidification while temperature change of side heater according to upward parabola, which is beneficial to improve the quality of polysilicon ingots.

Keywords

Interfacial morphology Directional solidification Thermal field Thermal stress 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgments

This work was supported by NSFC (No.51664047), The landing project of Jiangxi province of science and technology(20123BBE50116), the research project of Jiangxi provincial department of education science and technology (GJJ161200、GJJ161199).

References

  1. 1.
    Nguyen THT, Chen J-C, Hu C et al (2017) Numerical analysis of thermal stress and dislocation density distributions in large size multi-crystalline silicon ingots during the seeded growth process[J]. J Cryst Growth 468:316–320.  https://doi.org/10.1016/j.jcrysgro.2016.09.061 CrossRefGoogle Scholar
  2. 2.
    Tang YN, Shen HF (2010) Simulation for temperature distribution of polycrystalline silicon casting process[J]. Journal of System Simulation 22(7):1614–1617.  https://doi.org/10.16182/j.cnki.joss.2010.07.007 CrossRefGoogle Scholar
  3. 3.
    Smirnova OV, Mamedov VM, Kalaev VV (2014) Numerical modeling of stress and dislocations in Si ingots grown by seed-directional solidification and comparison to experimental data[J]. Cryst Growth Des 14:5532–5536.  https://doi.org/10.1021/cg500736j CrossRefGoogle Scholar
  4. 4.
    Hu C, Chen JC, Nguyen THT et al (2018) Optimization of heat transfer during the directional solidification process of 1600 kg silicon feedstock[J]. J Cryst Growth 484:70–77.  https://doi.org/10.1016/j.jcrysgro.2017.12.042 CrossRefGoogle Scholar
  5. 5.
    Wu ZY, Zhong GX, Zhou XC et al (2016) Upgrade of the hot zone for large-size high-performance multi-crystalline silicon ingot casting[J]. J Cryst Growth 441:58–63.  https://doi.org/10.1016/j.jcrysgro.2016.02.012 CrossRefGoogle Scholar
  6. 6.
    Lin T, Sun YH, Duan CY et al (2016) Influence of soaking time on polycrystalline silicon purification during directional solidification[J]. J Mater Sci Eng 34(4):643–646.  https://doi.org/10.14136/j.cnki.issn1673-2812.2016.04.027 CrossRefGoogle Scholar
  7. 7.
    Xu M, Zheng L, Zhang H et al (2011) Thermal system design and optimization of an industrial silicon directional solidification system[J]. J Cryst Growth 318:288–292.  https://doi.org/10.1016/j.jcrysgro.2010.10.102 CrossRefGoogle Scholar
  8. 8.
    Kesavan V, Srinivasan M, Ramasamy P (2018) The influence of multiple-heaters on the reduction of impurities in mc-Si for directional solidification[J]. Silicon:1–10.  https://doi.org/10.1007/s12633-018-9928-7 CrossRefGoogle Scholar
  9. 9.
    Anbu G, Srinivasan M, Ramasamy P (2018) Modelling on modified heater design of DS system for improving the quality of mc-silicon ingot[J]. Silicon:1–8.  https://doi.org/10.1007/s12633-018-9928-7 CrossRefGoogle Scholar
  10. 10.
    Chen W, Wu Z, Zhong G et al (2016) Optimization of heat transfer by adjusting power ratios between top and side heaters for casting high-performance multi-crystalline silicon ingots[J]. J Cryst Growth 451:155–160.  https://doi.org/10.1016/j.jcrysgro.2016.07.031 CrossRefGoogle Scholar
  11. 11.
    Li Z, Liu L, Zhang Y et al (2016) Influence of crucible thermal conductivity on crystal growth in an industrial directional solidification process for silicon ingots[J]. International Journal of Photoenergy.  https://doi.org/10.1155/2016/8032709 Google Scholar
  12. 12.
    Lu XD, Zhang P, Wu YQ et al (2015) Thermal field optimization and improvement of directional solidification of polycrystalline silicon ingot furnace quartz crucible[J]. Journal of Synthetic Crystal 44(11):3179–3183.  https://doi.org/10.16553/j.cnki.issn1000-985x.2015.11.044 CrossRefGoogle Scholar
  13. 13.
    Fang HS, Wang S, Zhou L et al (2012) Influence of furnace design on the thermal stress during directional solidification of multicrystalline silicon[J]. J Cryst Growth 346:5–11.  https://doi.org/10.1016/j.jcrysgro.2012.02.032 CrossRefGoogle Scholar
  14. 14.
    Wang S, Zhang QJ, Tian J et al (2015) Influence of inlet gas velocity bottom insulated plate movement on thermal stresses of silicon ingot during cooling process[J]. China Sciencepaper 10(11):1329–1333Google Scholar
  15. 15.
    Yang X, Ma W, Lv G et al (2014) A modified vacuum directional solidification system of multicrystalline silicon based on optimizing for heat transfer[J]. J Cryst Growth 400:7–14.  https://doi.org/10.1016/j.jcrysgro.2014.04.025 CrossRefGoogle Scholar
  16. 16.
    Li J, Chen Y, Hong R (2016) Modeling and optimization of the feedstock melting for industrial photovoltaic multi-crystalline silicon ingot[J]. Sol Energy 139:108–115.  https://doi.org/10.1016/j.solener.2016.09.024 CrossRefGoogle Scholar
  17. 17.
    Chen XJ, Nakano S, Liu LJ et al (2008) Study on thermal stress in a silicon ingot during a unidirectional solidification process[J]. J Cryst Growth 310:4330–4335.  https://doi.org/10.1016/j.jcrysgro.2008.07.027 CrossRefGoogle Scholar
  18. 18.
    Chen X, Nakano S, Kakimoto K (2010) Three-dimensional global analysis of thermal stress and dislocations in a silicon ingot during a unidirectional solidification process with a square crucible[J]. J Cryst Growth 312:3261–3266.  https://doi.org/10.1016/j.jcrysgro.2010.08.045 CrossRefGoogle Scholar
  19. 19.
    Nguyen THT, Liao S-H, Chen J-C et al (2016) Effects of the hot zone design during the growth of large size multi-crystalline silicon ingots by the seeded directional solidification process[J]. J Cryst Growth 452:27–34.  https://doi.org/10.1016/j.jcrysgro.2015.12.045 CrossRefGoogle Scholar
  20. 20.
    Kvande R, Mjos O, Ryningen B (2005) Growth rate and impurity distribution in multicrystalline silicon for solar cells[J]. Mater Sci Eng A 413-414:545–549.  https://doi.org/10.1016/j.msea.2005.09.035 CrossRefGoogle Scholar
  21. 21.
    Zhang FY, Rao SL, Wang FH et al (2017) Research Progress on the solid-liquid Interface in the crystal growth of polycrystalline silicon[J]. Journal of Synthetic Crystal 46(10):2077–2082.  https://doi.org/10.16553/j.cnki.issn1000-985x.2017.10.038 CrossRefGoogle Scholar
  22. 22.
    Nagarajan SG, Srinivasan M, Aravinth K et al (2018) Improving heat transfer properties of DS furnace by the geometrical modifications for enhancing the multi crystalline silicon ingot (mc-Si) quality using transient simulation[J]. Silicon:1–11.  https://doi.org/10.1007/s12633-018-9870-8 CrossRefGoogle Scholar
  23. 23.
    Yu Q, Liu L, Ma W et al (2012) Local design of the hot-zone in an industrial seeded directional solidification furnace for quasi-single crystalline silicon ingots[J]. J Cryst Growth 358:5–11.  https://doi.org/10.1016/j.jcrysgro.2012.07.039 CrossRefGoogle Scholar
  24. 24.
    Luo T, LV Q, Ma W et al (2013) Numerical and experimental study of vacuum directional solidification purification process for SoG-Si in metallurgicalroute[J]. J Cryst Growth 384:122–128.  https://doi.org/10.1016/j.jcrysgro.2013.09.020 CrossRefGoogle Scholar
  25. 25.
    Zhou B, Chen W, Dong H et al (2017) Effect of side insulation on stress and dislocation in the multi-crystalline silicon ingot during cooling process[J]. Journal of Materials Science and Engineering B:89–98.  https://doi.org/10.17265/2161-6221/2017.5-6.001
  26. 26.
    Chen XJ, Nakano S, Liu LJ et al (2008) Study on thermal stress in a silicon ingot during a unidirectional solidification process[J]. J Cryst Growth 310:4330–4335.  https://doi.org/10.1016/j.jcrysgro.2008.07.027 CrossRefGoogle Scholar

Copyright information

© Springer Nature B.V. 2019

Authors and Affiliations

  1. 1.School of Mechatronics EngineeringNanchang UniversityNanchangChina
  2. 2.Key Laboratory of Silicon Materials in Colleges of Jiangxi ProvinceXinyuChina
  3. 3.School of Mechatronics & Vehicle EngineeringEast China Jiaotong UniversityNanchangChina
  4. 4.School of New Energy Science and EngineeringXinyu UniversityXinyuChina

Personalised recommendations