Advertisement

Silicon

pp 1–14 | Cite as

Development and Properties of Centrifugally Cast Silicon Nitride Reinforced Functionally Graded Copper Matrix Composite

  • N. RadhikaEmail author
  • S. Thirumalini
  • R. Jojith
Original Paper
  • 17 Downloads

Abstract

The current study aims to synthesize copper alloy and functionally graded Cu-10Sn-5Ni/10Si3N4 composite using horizontal centrifugal casting method and compare their mechanical and adhesive wear characteristics. The fabricated castings have dimensions of Øout100 x Øin70 × 100 mm. Microstructural analysis revealed that inner region of composite possesses higher concentration of reinforcement particles, resulting in better hardness and tensile properties at this region compared to outer regions of both unreinforced alloy and composite. Analysis of dry sliding wear performance and frictional coefficient was performed at inner region of the composite under different sliding conditions using Taguchi’s method on pin-on-disc tribometer. Signal-to-Noise ratio and Analysis of Variance results concluded that applied load had the most influence on wear rate and coefficient of friction followed by sliding distance and sliding velocity. Worn surface morphologies of composite specimens revealed a transition from mild to severe wear at high loads. The fabricated composites are well suitable for sliding tribological applications.

Keywords

Functionally graded composite Copper Microhardness X-ray diffraction analysis Tensile strength Adhesive wear Friction 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgments

We are so thankful to Defense Research and Development Organization for providing the financial support. [ERIP/ER/1503188/M/01/1587].

References

  1. 1.
    Davis JR (2001) ASM Speciality Handbook: Copper and copper alloys. ASM international, 3-9.  https://doi.org/10.1361/caca2001p003
  2. 2.
    Phani PS, Vishnukanthan V, Sundararajan G (2007) Effect of heat treatment on properties of cold sprayed nanocrystalline copper alumina coatings. Acta Mater 55(14):4741–4751CrossRefGoogle Scholar
  3. 3.
    Radhika N, Raghu R (2015) Mechanical and tribological properties of functionally graded aluminium/zirconia metal matrix composite synthesized by centrifugal casting. Int J Mater Res 106(11):1174–1181CrossRefGoogle Scholar
  4. 4.
    Tjong SC, Lau KC (2000) Tribological behaviour of SiC particle-reinforced copper matrix composites. Mater Lett 43(5–6):274–280CrossRefGoogle Scholar
  5. 5.
    Macke A, Schultz BF, Rohatgi P (2012) Metal matrix composites. Adv Mater Process 170(3):19–23Google Scholar
  6. 6.
    Cole GS, Sherman AM (1995) Lightweight materials for automotive applications. Mater Charact 35(1):3–9CrossRefGoogle Scholar
  7. 7.
    Gogotsi YG (1994) Particulate silicon nitride-based composites. J Mater Sci 29(10):2541–2556CrossRefGoogle Scholar
  8. 8.
    Tu JP, Wang NY, Yang YZ, Qi WX, Liu F, Zhang XB, Lu HM, Liu MS (2002) Preparation and properties of TiB2 nanoparticle reinforced copper matrix composites by in situ processing. Mater Lett 52(6):448–452CrossRefGoogle Scholar
  9. 9.
    Akhtar F, Askari SJ, Shah KA, Du X, Guo S (2009) Microstructure, mechanical properties, electrical conductivity and wear behavior of high volume TiC reinforced Cu-matrix composites. Mater Charact 60(4):327–336CrossRefGoogle Scholar
  10. 10.
    Zhan Y, Zhang G (2003) Graphite and SiC hybrid particles reinforced copper composite and its tribological characteristic. J Mater Sci 22(15):1087–1089Google Scholar
  11. 11.
    Wu JY, Zhou YC, Wang JY (2006) Tribological behavior of Ti2SnC particulate reinforced copper matrix composites. Mater Sci Eng A 422(1–2):266–271CrossRefGoogle Scholar
  12. 12.
    Xia L, Jia B, Zeng J, Xu J (2009) Wear and mechanical properties of carbon fiber reinforced copper alloy composites. Mater Charact 60(5):363–369CrossRefGoogle Scholar
  13. 13.
    Kestursatya M, Kim JK, Rohatgi PK (2001) Friction and wear behavior of a centrifugally cast lead-free copper alloy containing graphite particles. Metall Mater Trans A 32(8):2115–2125CrossRefGoogle Scholar
  14. 14.
    Senthil Kumar P, Manisekar K, Subramanian E, Narayanaswamy R (2013) Dry sliding friction and wear characteristics of cu-Sn alloy containing molybdenum disulfide. Tribol T 56(5):857–866CrossRefGoogle Scholar
  15. 15.
    Radhika N, Raghu R (2016) Development of functionally graded Aluminium composites using centrifugal casting and influence of reinforcements on mechanical and Wear properties. Trans Nonferrous Metals Soc China 26(4):905–916CrossRefGoogle Scholar
  16. 16.
    Kieback B, Neubrand A, Riedel H (2003) Processing techniques for functionally graded materials. Mater Sci Eng A 362(1):81–106CrossRefGoogle Scholar
  17. 17.
    Chirita G, Soares D, Silva FS (2008) Advantages of the centrifugal casting technique for the production of structural components with Al–Si alloys. Mater Des 29(1):20–27CrossRefGoogle Scholar
  18. 18.
    Sharma P, Sharma S, Khanduja D (2015) Production and some properties of Si3N4 reinforced aluminium alloy composites. J Asian Ceramic Soc 3(3):352–359CrossRefGoogle Scholar
  19. 19.
    Whalen TJ, Anderson AT (1975) Wetting of SiC, Si3N4, and carbon by Si and binary Si alloys. J Am Ceram Soc 58(9–10):396–399CrossRefGoogle Scholar
  20. 20.
    Ramesh CS, Keshavamurthy R, Channabasappa BH, Ahmed A (2009) Microstructure and mechanical properties of Ni–P coated Si3N4 reinforced Al6061 composites. Mater Sci Eng A 502(1–2):99–106CrossRefGoogle Scholar
  21. 21.
    Amigo V, Ortiz JL, Salvador MD (2000) Microstructure and mechanical behavior of 6061Al reinforced with silicon nitride particles, processed by powder metallurgy. Scr Mater 42(4):383–388CrossRefGoogle Scholar
  22. 22.
    Lee KB, Kwon H (1999) Fabrication and characteristics of AA6061/Si3N4p composite by the pressureless infiltration technique. Metall. Mater. Trans. A 30(11):2999–3007CrossRefGoogle Scholar
  23. 23.
    Kumar NM, Kumaran SS, Kumaraswamidhas LA (2016) Wear behaviour of Al 2618 alloy reinforced with Si3N4, AlN and ZrB2 in situ composites at elevated temperatures. Alex Eng J 55(1):19–36CrossRefGoogle Scholar
  24. 24.
    Robin A, de Santana JCP, Sartori AF (2010) Characterization of copper–silicon nitride composite electrocoatings. J Appl Electrochem 40(3):507–513CrossRefGoogle Scholar
  25. 25.
    Radhika N, Subramaniam R (2013) Wear behaviour of aluminium/alumina/graphite hybrid metal matrix composites using Taguchi's techniques. Ind Lubr Tribol 65(3):166–174CrossRefGoogle Scholar
  26. 26.
    Basavarajappa S, Chandramohan G, Davim JP (2007) Application of Taguchi techniques to study dry sliding wear behaviour of metal matrix composites. Mater Des 28(4):1393–1398CrossRefGoogle Scholar
  27. 27.
    Radhika N, Vaishnavi A, Chandran GK (2014) Optimisation of dry sliding wear process parameters for Aluminium hybrid metal matrix composites. Tribol Ind 36(2):188–194Google Scholar
  28. 28.
    Theivasanthi T, Alagar M (2010) X-ray diffraction studies of copper nanopowder. arXiv preprint arXiv: 1003.6068Google Scholar
  29. 29.
    Bai YJ, Bian J, Wang CG, Zhu B, Qi YX, Wang YX, Liu YX, Geng GL (2005) One step convenient synthesis of crystalline β-Si3N4. J Mater Chem 15(45):4832–4837CrossRefGoogle Scholar
  30. 30.
    Mandal A, Maiti R, Chakraborty M, Murty BS (2004) Effect of TiB2 particles on aging response of Al–4Cu alloy. Mater Sci Eng A 386(1–2):296–300CrossRefGoogle Scholar
  31. 31.
    Deshpande PK, Lin RY (2006) Wear resistance of WC particle reinforced copper matrix composites and the effect of porosity. Mater Sci Eng A 418(1–2):137–145CrossRefGoogle Scholar
  32. 32.
    Hong E, Kaplin B, You T, Suh MS, Kim YS, Choe H (2011) Tribological properties of copper alloy-based composites reinforced with tungsten carbide particles. Wear 270:591–597CrossRefGoogle Scholar
  33. 33.
    Zhang L, He XB, Qu XH, Duan BH, Lu X, Qin ML (2008) Dry sliding wear properties of high volume fraction SiCp/Cu composites produced by pressureless infiltration. Wear 265(11–12):1848–1856CrossRefGoogle Scholar
  34. 34.
    Nayak D, Ray N, Sahoo R, Debata M (2014) Analysis of tribological performance of Cu hybrid composites reinforced with graphite and TiC using factorial techniques. Tribol Trans 57:908–918CrossRefGoogle Scholar
  35. 35.
    Sangaravadivel P, Natarajan N, Krishnaraj V (2016) Experimental investigation and optimization of dry sliding Wear parameters on solid lubricant reinforced bronze matrix composites-a Taguchi approach. Appl Mech Mater 852:435–445CrossRefGoogle Scholar
  36. 36.
    Zhan Y, Zhang G (2004) Friction and wear behavior of copper matrix composites reinforced with SiC and graphite particles. Tribol Lett 17(1):91–98CrossRefGoogle Scholar
  37. 37.
    Das Bakshi S, Leiro A, Prakash B, Bhadeshia HK (2015) Dry rolling/sliding wear of nanostructured pearlite. Mater Sci Technol 31(14):1735–1744CrossRefGoogle Scholar
  38. 38.
    Zhang G, Schlarb AK (2009) Morphologies of the wear debris of polyetheretherketone produced under dry sliding conditions: correlation with wear mechanisms. Wear 266(7–8):745–752CrossRefGoogle Scholar

Copyright information

© Springer Nature B.V. 2019

Authors and Affiliations

  1. 1.Department of Mechanical Engineering, Amrita School of EngineeringAmrita Vishwa VidyapeethamCoimbatoreIndia

Personalised recommendations