Advertisement

Effect of continuous casting speed on mold surface flow and the related near-surface distribution of non-metallic inclusions

  • Peng Fei
  • Yi MinEmail author
  • Cheng-jun Liu
  • Mao-fa Jiang
Article

Abstract

For the control of surface defects in interstitial-free (IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al2O3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface.

Keywords

non-metallic inclusions distribution casting speed surface flow 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgements

This work was financially supported by the National Natural Science Foundation of China (No. 51674069) and the National Key R & D Program of China (No. 2017YFC0805100).

References

  1. [1]
    M. Takahashi, Sheet steel technology for the last 100 years: Progress in sheet steels in hand with the automotive industry, ISIJ Int., 55(2015), No. 1, p. 79.CrossRefGoogle Scholar
  2. [2]
    T. EMI, Steelmaking technology for the last 100 years: toward highly efficient mass production systems for high quality steels, ISIJ Int., 55(2015), No. 1, p. 36.CrossRefGoogle Scholar
  3. [3]
    H.X. Yu, C.X. Ji, B. Chen, C. Wang, and Y.H. Zhang, Characteristics and evolution of inclusion induced surface defects of cold rolled IF sheet, J. Iron Steel Res. Int., 22(2015), Suppl. 1, p. 17.CrossRefGoogle Scholar
  4. [4]
    B.G. Thomas, Review on modeling and simulation of continuous casting, Steel Res. Int., 89(2018), No. 1, art. No. 1700312.Google Scholar
  5. [5]
    M. Iguchi, J. Yoshida, T. Shimizu, and Y. Mizuno, Model study on the entrapment of mold powder into molten steel, ISIJ Int., 40(2000), No. 7, p. 685.CrossRefGoogle Scholar
  6. [6]
    B.G. Thomas, Modeling of the continuous casting of steel—past, present, and future, Metall. Mater. Trans., B, 33(2002), No. 6, p. 795.CrossRefGoogle Scholar
  7. [7]
    X.X. Deng, L.P. Li, X.H. Wang, Y.Q. Ji, C.X. Ji, and G.S. Zhu, Subsurface macro-inclusions and solidified hook character in aluminum-killed deep-drawing steel slabs, Int. J. Miner. Metall. Mater., 21(2014), No. 6, p. 531.CrossRefGoogle Scholar
  8. [8]
    M.M. Jaradeh and T. Carlberg, Analysis of distribution of nonmetallic inclusions in aluminum DC-cast billets and slabs, Metall. Mater. Trans. B, 43(2012), No. 1, p. 82.CrossRefGoogle Scholar
  9. [9]
    R. Liu, J Sengupta, D. Crosbie, S. Chung, M. Trinh, and B.G. Thomas, Measurement of molten steel surface velocity with SVC and nail dipping during continuous casting process, [in] Symposium on Sensors, Sampling, and Simulation for Process Control Held during the 140th TMS Annual Meeting and Exhibition, San Diego, 2011, p. 51.CrossRefGoogle Scholar
  10. [10]
    S.M. Cho, S.H. Kim, and B.G. Thomas, Transient fluid flow during steady continuous casting of steel slabs: part i. measurements and modeling of two-phase flow, ISIJ Int., 54(2014), No. 4, p. 845.CrossRefGoogle Scholar
  11. [11]
    H.Q. Yu, M.Y. Zhu, and J. Wang, Interfacial fluctuation behavior of steel/slag in medium-thin slab continuous casting mold with argon gas injection, J. Iron Steel Res. Int., 17(2010), No. 4, p. 5.CrossRefGoogle Scholar
  12. [12]
    Y.B. Yin, J.M. Zhang, S.W. Lei, and Q.P. Dong, Numerical study on the capture of large inclusion in slab continuous casting with the effect of in-mold electromagnetic stirring, ISIJ Int., 57(2017), No. 12, p. 2165.CrossRefGoogle Scholar
  13. [13]
    B.G. Thomas, Q. Yuan, S. Mahmood, R. Liu, and R. Chaudhary, Transport and entrapment of particles in steel continuous casting, Metall. Mater. Trans. B, 45(2014), No. 1, p. 22.CrossRefGoogle Scholar
  14. [14]
    X.P. Song, S.S. Cheng, and Z.J. Cheng, Numerical computation for metallurgical behavior of primary inclusion in compact strip production mold, ISIJ Int., 52(2012), No. 10, p. 1824.CrossRefGoogle Scholar
  15. [15]
    C.P. Nie, X.F. Zhang, B. Wang, Y.H. Sun, and Q. Liu, Characteristics of inclusion motion and accumulation in CSP mold, ISIJ Int., 55(2015), No. 8, p. 1677.CrossRefGoogle Scholar
  16. [16]
    S.M. Cho, H.J. Lee, S.H. Kim, R. Chaudhary, B.G. Thomas, D.H. Lee, Y.J. Kim, W.R. Choi, S.K. Kim, and H.S. Kim, Measurement of transient meniscus flow in steel continuous casters and effect of electromagnetic braking, [in] Symposium on Sensors, Sampling, and Simulation for Process Control Held during the 140th TMS Annual Meeting and Exhibition, San Diego, 2011, p. 59.CrossRefGoogle Scholar
  17. [17]
    A.V. Karasev and H. Suito, Characteristics of fine oxide particles produced by Ti/M (M=Mg and Zr) complex deoxidation in Fe-10mass%Ni alloy, ISIJ Int., 48(2008), No. 11, p. 1507.CrossRefGoogle Scholar
  18. [18]
    D.Y. Wang, M.F. Jiang, H. Matsuura, and F. Tsukihashi, Dynamic evolution of inclusions in Ti-bearing Al-deoxidized molten irons at 1873 K, Steel Res. Int., 85(2014), No. 1, p. 16.CrossRefGoogle Scholar
  19. [19]
    H.Q. Yu and M.Y. Zhu, Numerical simulation of the effects of electromagnetic brake and argon gas injection on the three-dimensional multiphase flow and heat transfer in slab continuous casting mold, ISIJ Int., 48(2008), No. 5, p. 584.CrossRefGoogle Scholar
  20. [20]
    N. Kubo, T. Ishii, J. Kubota, and N. Aramaki, Two-phase flow numerical simulation of molten steel and argon gas in a continuous casting mold, ISIJ Int., 42(2002), No. 11, p. 1251.CrossRefGoogle Scholar
  21. [21]
    R. Chaudhary, G.G. Lee, B.G. Thomas, and S.H. Kim, Transient mold fluid flow with well- and mountain-bottom nozzles in continuous casting of steel, Metall. Mater. Trans. B, 39(2008), No. 6, p. 870.CrossRefGoogle Scholar
  22. [22]
    R. McDavid and B.G. Thomas, Flow and thermal behavior of the top surface flux/powder layers in continuous casting molds, Metall. Mater. Trans. B, 27(1996), No. 4, p. 672.CrossRefGoogle Scholar
  23. [23]
    A. Hajari and M. Meratian, Surface turbulence in a physical model of a steel thin slab continuous caster, Int. J. Miner. Metall. Mater., 17(2010), No. 6, p. 697.CrossRefGoogle Scholar
  24. [24]
    J. Sengupta, B.G. Thomas, H.J. Shin, G.G. Lee, and S.H. Kim, A new mechanism of hook formation during continuous casting of ultra-low-carbon steel slabs, Metall. Mater. Trans. A, 37(2006), No. 5, p. 1597.CrossRefGoogle Scholar

Copyright information

© University of Science and Technology Beijing and Springer-Verlag GmbH Germany, part of Springer Nature 2019

Authors and Affiliations

  • Peng Fei
    • 1
    • 2
  • Yi Min
    • 1
    • 2
    Email author
  • Cheng-jun Liu
    • 1
    • 2
  • Mao-fa Jiang
    • 1
    • 2
  1. 1.Key Laboratory for Ecological Metallurgy of Multimetallic Mineral (Ministry of Education)ShenyangChina
  2. 2.School of Metallurgy, Northeastern UniversityhenyangChina

Personalised recommendations