Advertisement

Research on Friction Characteristics of AlCrN and TiAlSiN Coatings and Properties of Coated Tools

  • Qi-Bin Yue
  • Hui-Bo HeEmail author
  • Hua-Ying Li
  • Jun Zhang
  • Yuan-Ming Li
  • Lu Ma
Regular Paper
  • 76 Downloads

Abstract

AlCrN and TiAlSiN coatings were deposited on the surface of 30CrMnSi steel and cemented carbide YT15 by multi-arc ion plating technique. A scanning electron microscopy was used to observe the surface morphologies of both coatings. The reciprocating sliding tests of AlCrN and TiAlSiN coating were performed to investigate the friction coefficients and the wear mechanisms of both coatings were analyzed as well. Dry machining tests on 30CrMnSi hardened steel were carried out with the AlCrN and TiAlSiN coated tools on a CA6140A lathe. The effects of cutting speed on cutting forces and cutting temperatures of AlCrN and TiAlSiN coated tools were obtained and analyzed. The microcosmic micrographs of wear areas of both coated tools were observed and investigated by scanning electron microscope and energy dispersive spectrum. The results show that the hardness and bonding strength of AlCrN coating are higher than that of TiAlSiN coating, while the friction coefficient of AlCrN coating is lower than that of TiAlSiN coating. Both the cutting force and cutting temperature of AlCrN coated tool are lower than TiAlSiN coated tool. The time required for the bluntness of the AlCrN coated tool is approximately 33.3% longer than that of the TiAlSiN coated tool, and the main wear mechanisms of both tools are mainly crater wear, diffusion wear and oxidation wear.

Keywords

AlCrN TiAlSiN Cutting force Cutting temperature Tool wear 

Notes

Acknowledgements

This work was supported by the Fundamental Research Funds for the Central Universities of Ministry of Education of People’s Republic of China (XDJK2017C081) and the Cooperative research and development of scientific research prototype (180029).

References

  1. 1.
    Chang, H. B., Li, S. Y., & Shi, R. P. (2017). Design and manufacturing technology of high speed milling cutter for aluminum alloy. Procedia Engineering, 174, 630–637.CrossRefGoogle Scholar
  2. 2.
    TenNer, J., Zhao, R., Tremmel, S., Häfner, T., Schmidt, M., & Merklein, M. (2018). Tribological behavior of carbon based coatings adapted to lubricant-free forming conditions. International Journal of Precision Engineering and Manufacturing-Green Technology, 5, 361–367.CrossRefGoogle Scholar
  3. 3.
    Li, H. Y., He, H. B., & Han, W. Q. (2015). A study on cutting and tribology performances of TiN and TiAlN coted tools. International Journal of Precision Engineering and Manufacturing, 16(4), 781–786.CrossRefGoogle Scholar
  4. 4.
    Kataoka, R., & Shamoto, E. (2019). Influence of vibration in cutting on tool flank wear: fundamental study by conducting a cutting experiment with forced vibration in the depth-of-cut direction. Precison Engineering, 55, 322–329.CrossRefGoogle Scholar
  5. 5.
    Kuo, C. L., Wang, C. Y., & Ko, S. K. (2018). Wear behavior of CVD diamond—coated tools in the drilling of woven CFRP composites. Wear, 398–399, 1–12.CrossRefGoogle Scholar
  6. 6.
    Hosokawa, A., Hosino, G., Koyano, T., & Ueda, T. (2018). Cutting characteristics of PVD-coated tools deposited by filtered arc deposition (FAD) method. CIRP Annals, 67(1), 83–86.CrossRefGoogle Scholar
  7. 7.
    Wu, T., Li, T. J., Ding, X. H., Chen, H., & Wang, L. (2018). Design of a modular green closed internal cooling turning tool for applications. International Journal of Precision Engineering and Manufacturing-Green Technology, 5, 211–217.CrossRefGoogle Scholar
  8. 8.
    Durmaz, Y. M., & Yildiz, F. (2019). The wear performance of carbide tools coated with TiAlSiN, AlCrN and TiAlN ceramic films in intelligent machining process. Ceramics International, 45, 3839–3848.CrossRefGoogle Scholar
  9. 9.
    Liu, W., Chu, Q. Q., & He, R. X. (2018). Preparation and properties of TiAlN coatings on silicon nitride ceramic cutting tools. Ceramics International, 44, 22019–22215.CrossRefGoogle Scholar
  10. 10.
    Li, G. D., Sun, J. F., & Xu, Y. (2018). Microstructure, mechanical properties, and cutting performance of TiAlSiN multilayer coatings prepared by HiPIMS. Surface and Coatings Technology, 353, 274–281.CrossRefGoogle Scholar
  11. 11.
    Chang, Y. Y., Weng, S. Y., Chen, C. H., & Fu, F. X. (2017). High temperature oxidation and cutting performance of AlCrN, TiVN and multilayered AlCrN/TiVN hard coatings. Surface and Coatings Technology, 332, 494–503.CrossRefGoogle Scholar
  12. 12.
    Zhou, J., Feng, Z. D., & Fan, X. F. (2018). Effect of negative bias on TiAlSiN coating deposited on nitride Zircaloy-4. Journal of Nuclear Materials, 498, 76–82.CrossRefGoogle Scholar
  13. 13.
    Mo, J. L., Zhu, M. H., & Lei, B. (2007). Comparison of tribological behaviors of AlCrN and TiAlN coatings deposited by physical vapor deposition. Wear, 263, 1423–1429.CrossRefGoogle Scholar
  14. 14.
    Antonov, M., Afshari, H., & Baronins, J. (2018). The effect of temperature and sliding speed on friction and wear of Si3N4, Al2O3, and ZrO2 balls tested against AlCrN PVD coating. Tribology International, 188, 400–514.Google Scholar
  15. 15.
    He, N., Li, H. X., & Ji, L. (2016). High temperature tribological properties of TiAlSiN coatings produced by hybrid PVD technology. Tribology International, 98, 133–143.CrossRefGoogle Scholar
  16. 16.
    Skordaris, G., Bouzakis, K. D., & Kotsanis, T. (2017). Effect of PVD film’s residual stresses on their mechanical properties, brittleness, adhesion and cutting performance of coated tools. CIRP Journal of Manufacturing Science and Technology, 18, 145–151.CrossRefGoogle Scholar
  17. 17.
    Gong, M. F., Chen, J., Deng, X., & Wu, S. H. (2017). Sliding wear behavior of TiAlN and AlCrN coatings on a unique cemented carbide substrate. International Journal of Refractory Metals and Hard Materials, 69, 209–214.CrossRefGoogle Scholar
  18. 18.
    Chen, W. L., Zheng, J., & Zhang, S. H. (2015). Investigation on microstructures and mechanical properties of AlCrN coatings deposited on the surface of plasma nitrocarburized cool-work tool steels. Vacuum, 121, 194–201.CrossRefGoogle Scholar
  19. 19.
    Zheng, G. M., Xu, R. F., & Cheng, X. (2018). Effect of cutting parameters on wear behavior of coated tool and surface roughness in high-speed turning of 300M. Measurement, 125, 99–108.CrossRefGoogle Scholar
  20. 20.
    He, H. B., Li, H. Y., Zhang, X. Y., Yue, Q. B., Zhang, J., Ma, L., et al. (2019). Research on the cutting performances and wear mechanisms of TiAlCrN coated tools during dry turning. International Journal of Precision Engineering and Manufacturing, 20, 201–207.CrossRefGoogle Scholar
  21. 21.
    Karaguzel, U., & Budak, E. (2018). Investigating effects of milling conditions on cutting temperatures through analytical and experimental methods. Journal of Materials Processing Technology, 262, 532–540.CrossRefGoogle Scholar
  22. 22.
    Xu, J. H., He, L. J., Su, H. H., & Zhang, L. (2018). Tool wear investigation in high-pressure jet coolant assisted machining Ti2AlNb intermetallic alloys based on FEM. International Journal of Lightweight Materials and Manufacture, 1, 219–228.CrossRefGoogle Scholar

Copyright information

© Korean Society for Precision Engineering 2019

Authors and Affiliations

  1. 1.College of Engineering and TechnologySouthwest UniversityChongqingPeople’s Republic of China
  2. 2.Chongqing Key Laboratory of Agriculture Equipment for Hilly and Mountainous RegionsChongqingPeople’s Republic of China
  3. 3.School of Mechanical and Aerospace Engineering, ReCAPT (K-MEM R&D Cluster)Gyeongsang National UniversityJinjuSouth Korea

Personalised recommendations