Effect of Mn Addition on Microstructural Changes and Mechanical Properties of Ti–5Al–2.5Fe Alloys

  • Gyeong Ryeong Bak
  • Dae-Won Jeong
  • Yong Taek Hyun
  • Hyun Soon Park
Article
  • 39 Downloads

Abstract

The microstructures and mechanical properties were investigated in newly developed Ti–5Al–2.5Fe and Ti–5Al–2.5Fe–2Mn alloys, which were fabricated by two-step hot rolling processes. Lamellar structures were observed in the Ti–5Al–2.5Fe–2Mn alloy aged at 600 °C for 24 h, depending on the viewing directions (normal, rolling, and transverse). In the aged Ti–5Al–2.5Fe alloy, a spheroidized α matrix and TiFe precipitates in the α grain boundary were observed, with a crystallographic orientation relationship of (011)TiFe//(01\(\overline{1}\)0)α. It was found that Mn addition improved the mechanical properties, attributed to the increased β phase (approximately 4.3 times relative to the Ti–5Al–2.5Fe alloy) and solid solution strengthening. Interestingly, in the Ti–5Al–2.5Fe alloys, the oxygen was enriched by the TiFe phase rather than the α phase, which may weaken the oxygen solute dragging effect.

Keywords

Titanium alloys Mn addition Transmission electron microscopy Strain/stress measurements Phase fraction Oxygen 

Notes

Acknowledgements

The authors are grateful to Dr. J. C. Park for EELS measurements. This research was supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF-2016R1D1A1B03934213) funded by the Ministry of Education and by INHA UNIVERSITY Research Grant (INHA-55432) as well as by Materials/Components Technology Development Program of Korea Evaluation Institute of Industrial Technology (Grant No. 10050608).

References

  1. 1.
    L. Xiao, S.G. Tian, X.Y. Bao, L.Q. Chen, Influence of heat treatment on microstructure and creep properties continuous rolled Ti–6Al–4V alloy. Mater. Sci. Eng. A 559, 401–406 (2013)CrossRefGoogle Scholar
  2. 2.
    I. Bantounas, T.C. Lindley, D. Rugg, D. Dye, Effect of microtexture on fatigue cracking in Ti–6Al–4V. Acta Mater. 55, 5655–5665 (2007)CrossRefGoogle Scholar
  3. 3.
    J. Koike, Y. Shimoyama, I. Ohnuma, T. Okamura, R. Kainuma, K. Ishida, K. Maruyama, Stress-induced phase transformation during superplastic deformation in two-phase Ti–Al–Fe alloys. Acta Mater. 48, 2059–2069 (2000)CrossRefGoogle Scholar
  4. 4.
    M. Niinomi, Mechanical properties of biomedical titanium alloys. Mater. Sci. Eng. A 243, 231–236 (1998)CrossRefGoogle Scholar
  5. 5.
    B.H. Choe, W.Y. Choi, J.H. Shim, C.H. Park, J.H. Kang, S.E. Kim, Y.T. Hyun, Microstructural analysis of thermo-mechanical processed Ti–6Al–4Fe alloy. Korean J. Mater. Res. 25, 8 (2015)Google Scholar
  6. 6.
    M. Arulselvan, G. Ganesan, Hot deformation behavior of Ti–6Al–4V in different strain rates. IJIRAE 1, 207–212 (2014)Google Scholar
  7. 7.
    H. Fujii, Strengthening of α + β titanium alloys by thermomechanical processing. Mater. Sci. Eng. A 243, 103–108 (1998)CrossRefGoogle Scholar
  8. 8.
    G. Lutjering, Influence of processing on microstructure and mechanical properties of (α + β) titanium alloys. Mater. Sci. Eng. A 243, 32–45 (1998)CrossRefGoogle Scholar
  9. 9.
    S.-W. Kim, J.H. Kim, Y.H. Song, J.K. Hong, Y.T. Hyun, J.-T. Yeom, Deformation characteristics of Ti-6Al-4Fe alloys with enhanced high temperature ductility. Mater. Sci. Eng. A 559, 96–100 (2013)CrossRefGoogle Scholar
  10. 10.
    J. Koike, Y. Shimoyama, H. Fujii, K. Maruyama, Characterization of superplasticity in Ti-5.5Al-1Fe alloys. Scripta Mater. 39, 1009–1014 (1998)CrossRefGoogle Scholar
  11. 11.
    Y.H. Song, J.H. Kang, C.H. Park, S.-W. Kim, Y.T. Hyun, N.H. Kang, J.-T. Yeom, Microstructure evolution of Ti-6Al-4Fe-0.25Si through aging heat treatment, Korean. J Met. Mater. 50, 477–485 (2012)Google Scholar
  12. 12.
    P. Zeitz, J.E. Wittig, G. Frommeyer, Eutectoid decomposition and mechanical properties of TiFe(Al) alloys. Scripta Metall. 20, 757–762 (1986)CrossRefGoogle Scholar
  13. 13.
    A.I. Kahveci, G.E. Welsch, Effect of oxygen on the hardness and alpha/beta phase ratio of Ti–6Al–4V alloy. Scripta Metall. 20, 1287–1290 (1986)CrossRefGoogle Scholar
  14. 14.
    J.-M. Oh, B.-G. Lee, S.-W. Cho, S.-W. Lee, G.-S. Choi, J.-W. Lim, Oxygen effects on the mechanical properties and lattice strain of Ti and Ti–6Al–4V. Met. Mater. Int. 17, 733–736 (2011)CrossRefGoogle Scholar
  15. 15.
    Q. Yu, L. Qi, T. Tsuru, R. Traylor, D. Rugg, J.W. Morris Jr., M. Asta, D.C. Chrzan, A.M. Minor, Origin of dramatic oxygen solute strengthening effect in titanium. Science 347, 635–639 (2015)CrossRefGoogle Scholar
  16. 16.
    A.K. De, D.C. Murdock, M.C. Mataya, J.G. Speer, D.K. Matlock, Quantitative measurement of deformation-induced martensite in 304 stainless steel by X-ray diffraction. Scirpta Mater. 50, 1445–1449 (2004)CrossRefGoogle Scholar
  17. 17.
    I. Weiss, S.L. Semiatin, Thermomechanical processing of beta titanium alloys-an overview. Mater. Sci. Eng. A 243, 46–65 (1998)CrossRefGoogle Scholar
  18. 18.
    D.-S. Kang, N. Koga, M. Sakata, N. Nakada, T. Tsuchiyama, S. Takaki, Enhanced work hardening by redistribution of oxygen in (α + β)-type Ti–4Cr–0.2O alloys. Mater. Sci. Eng. A 606, 101–107 (2014)CrossRefGoogle Scholar
  19. 19.
    M.N. Vijayshankar, S. Ankem, High temperature tensile deformation behavior of β-Ti alloys. Mater. Sci. Eng. A 129, 229–237 (1990)CrossRefGoogle Scholar
  20. 20.
    M. Peters, J. Hemptenmacher, J. Kumpfert, C. Leyens, Titanium and titanium alloys—fundamentals and applications, C. Leyens, M. Peters, WILEY-VCH (2003) pp. 1–35Google Scholar
  21. 21.
    D.-G. Lee, S.H. Lee, C.S. Lee, Quasi-static and dynamic deformation behavior of Ti–6Al–4V alloy containing fine α2-Ti3Al precipitates. Mater. Sci. Eng. A 366, 25–37 (2004)CrossRefGoogle Scholar
  22. 22.
    H.H. Wu, D.R. Trinkle, Direct diffusion through interpenetrating networks: oxygen in titanium. Phys. Rev. Lett. 107, 045504-1–045504-4 (2011)Google Scholar

Copyright information

© The Korean Institute of Metals and Materials 2018

Authors and Affiliations

  • Gyeong Ryeong Bak
    • 1
    • 2
  • Dae-Won Jeong
    • 1
    • 2
  • Yong Taek Hyun
    • 2
  • Hyun Soon Park
    • 3
  1. 1.Department of Materials Science and EngineeringDong-A UniversityBusanRepublic of Korea
  2. 2.Titanium DepartmentKorea Institute of Materials Science (KIMS)ChangwonRepublic of Korea
  3. 3.Department of Materials Science and EngineeringInha UniversityIncheonRepublic of Korea

Personalised recommendations