Advertisement

International Journal of Material Forming

, Volume 12, Issue 2, pp 223–240 | Cite as

Analysis of non-isothermal warm deep drawing of dual-phase DP600 steel

  • T. PepelnjakEmail author
  • E. Kayhan
  • B. Kaftanoglu
Thematic Issue: Advances in Material Forming Simulation

Abstract

Improving the formability of the material is a key issue in the deep drawing process. Heating the material above its recrystallization temperature drastically increases formability, but in the case of dual phase (DP) steels, it results in a loss of their mechanical properties. To improve the drawing ratio, only the heating of the flange region in the warm temperature range up to 573 K was studied on DP600 sheet steel by numerical simulation. A thermo-elastic-plastic finite element method (FEM) analysis of deep drawing at several drawing ratios was performed and compared with experimental results. During the experiments, the flange area of the blank was heated by induction heating, and the central part over the punch was cooled with spray water. Experimental results showed that limiting drawing ratio could be increased by 25.58%. The microstructure of the DP 600 steel was analyzed before and after the warm forming process. No significant changes were observed, and the high strength properties of the DP 600 steel remained intact. There was good agreement between numerical and experimental results.

Keywords

Sheet metal forming Dual-phase steel Numerical simulation Warm forming Drawing ratio 

Notes

Acknowledgements

The authors would like to acknowledge the financial support received from The Scientific and Technological Research Council of Turkey (TUBITAK) and Slovenia(ARRS) under Project No: 111 M448 and from ATILIM University under the project No: ATÜ-BAP-1011-13. The use of facilities in the Metal Forming Center of Excellence at ATILIM University as well as Faculty of Natural Sciences and Engineering, University of Ljubljana is also acknowledged and thanks are extended to the personnel for their contributions on the material tests and the use of HPC.

Compliance with ethical standards

Conflict of Interest

There is no conflict of interest.

References

  1. 1.
    Sadagopan S, Urban D (2003) Roadmap Project TRP#0012, American Iron and Steel Institute/Department of Energy TechnologyGoogle Scholar
  2. 2.
    Anonymous (2014) Advanced high-strength steels application guidelines, version 5.0. World Auto Steel, BrusselsGoogle Scholar
  3. 3.
    Aydin H, Essadiqi E, Jung I-H, Yue S (2013) Development of 3rd generation AHSS with medium Mn content alloying compositions. Mat Sci Eng A 564:501–508CrossRefGoogle Scholar
  4. 4.
    Krupitzer R (2012) AHSS technology workshop. Steel Market Development Institute, SouthfieldGoogle Scholar
  5. 5.
    Bandyopadhyay K, Panda SK, Saha P, Padmanabham G (2015) Limiting drawing ratio and deep drawing behavior of dual phase steel tailor welded blanks: FE simulation and experimental validation. J Mater Process Technol 217:48–64CrossRefGoogle Scholar
  6. 6.
    Ingarao G, Di Lorenzo R, Micari F (2009) Analysis of stamping performances of dual phase steels: a multi-objective approach to reduce springback and thinning failure. Mat Des 30:4421–4433CrossRefGoogle Scholar
  7. 7.
    Tekkaya AE et al (2015) Metal forming beyond shaping: predicting and setting product properties. CIRP Ann 64:629–653CrossRefGoogle Scholar
  8. 8.
    Lei C, Cui J, Xing Z, Fu H, Zhao H (2012) Investigation of cooling effect of hot-stamping dies by numerical simulation. Phys Proc 25:118–124CrossRefGoogle Scholar
  9. 9.
    Verma RK, Biswas P, Kuwabara T, Chung K (2014) Two stage deformation modeling for DP 780 steel sheet using crystal plasticity. Mat Sci Eng A 604:98–102CrossRefGoogle Scholar
  10. 10.
    Kim T, Altan T, Yan Q (2009) Evaluation of stamping lubricants in forming advanced high strength steels (AHSS) using deep drawing and ironing tests. J Mater Process Technol 209:4122–4133CrossRefGoogle Scholar
  11. 11.
    Mackensen A, Golle M, Golle R, Hoffmann H (2010) Experimental investigation of the cutting force reduction during the blanking operation of AHSS sheet materials. CIRP Ann 59:283–286CrossRefGoogle Scholar
  12. 12.
    Kim H, Han S, Yan Q, Altan T (2009) Evaluation of stamping lubricants in forming advanced high strength steels (AHSS) using deep drawing and ironing tests. CIRP Ann 57:299–304CrossRefGoogle Scholar
  13. 13.
    Cora ÖN, Ağcayazı A, Namiki K, Sofuoğlu H, Koc M (2012) Die wear in stamping of advanced high strength steels – Investigations on the effects of substrate material and hard-coatings. Tribol Int 52:50–60CrossRefGoogle Scholar
  14. 14.
    Abdollahpoor A, Chen X, Pereira MP, Xiao N, Rolfe BF (2016) Sensitivity of the final properties of tailored hot stamping components to the process and material parameters. J Mater Process Technol 228:125–136CrossRefGoogle Scholar
  15. 15.
    Merklein M, Wielanda M, Lechnera M, Bruschib S, Ghiotti A (2016) Hot stamping of boron steel sheets with tailored properties: a review. J Mater Process Technol 228:11–24CrossRefGoogle Scholar
  16. 16.
    Lehtinen P, Väisänen T, Salmi M (2015) The effect of local heating by laser irradiation for aluminum, deep drawing steel and copper sheets in incremental sheet forming. Phys Proc 78:312–319CrossRefGoogle Scholar
  17. 17.
    Neugebauer R, Altan T, Geiger M, Kleiner M, Sterzing A (2006) Sheet metal forming at elevated temperatures. Ann CIRP 55(2):793–816CrossRefGoogle Scholar
  18. 18.
    Kleiner M, Geiger M, Klaus A (2003) Manufacturing of lightweight components by metal forming. Ann CIRP 52(2):521–542CrossRefGoogle Scholar
  19. 19.
    Mori K, Maki S, Tanaka Y (2005) Warm and hot stamping of ultra high tensile strength steel sheets using resistance heating. Ann CIRP 54(1):209–212CrossRefGoogle Scholar
  20. 20.
    Bruschi S, Altan T, Banabic D, Bariani PF, Brosius A, Cao J, Ghiotti A, Khraisheh M, Merklein M, Tekkaya AE (2014) Testing and modelling of material behaviour and formability in sheet metal forming. Ann CIRP 63(2):727–749CrossRefGoogle Scholar
  21. 21.
    Kaya S, Spampinato G, Altan T (2008) An experimental study on nonisothermal deep drawing process using aluminium and magnesium alloys. J Manuf Sci E-T ASME 130(061001–1):061001–061011CrossRefGoogle Scholar
  22. 22.
    Yoshihara S, Nishimura H, Yamamoto H, Manabe K (2003) Formability enhancement in magnesium alloy stamping using a local heating and cooling technique: circular cup deep drawing process. J Mater Process Technol 142:609–613CrossRefGoogle Scholar
  23. 23.
    Gelin JC, Moisan A (1986) Application of a thermo-viscoplastic model to the analysis of defects in warm forming conditions. Ann CIRP 35(1):157–160CrossRefGoogle Scholar
  24. 24.
    Ota E, Yogo Y, Iwata T et al (2014) Formability improvement technique for heated sheet metal forming by partial cooling. Key Eng Mater 622-623:279–283CrossRefGoogle Scholar
  25. 25.
    Kayhan E (2015) The development of a method to improve the limit drawing ratio of blanks using preferential heating. Dissertation, Atilim UniversityGoogle Scholar
  26. 26.
    Billur E, Altan T (2014) Three generations of advanced high-strength steels for automotive applications. Stamping J, Parts 1–3, pp 16–17, 12–13, 12–13Google Scholar
  27. 27.
    Saxena KK, Drotleff K, Mukhopadhyay J (2016) Elevated temperature forming limit strain diagrams of automotive alloys Al6014-T4 and DP600: A case study. J Strain Anal 51(6):459–470.  https://doi.org/10.1177/0309324716651028 CrossRefGoogle Scholar
  28. 28.
    Hua C, Yina Q, Zhao Z, Ou H (2017) A new measuring method for friction factor by using ring with inner boss compression test. Int J Mech Sci 123:133–140.  https://doi.org/10.1016/j.ijmecsci.2017.01.042 CrossRefGoogle Scholar
  29. 29.
    Schey JA (1983) Tribology in metal working: friction, lubrication and wear. AMS, Metals ParkGoogle Scholar
  30. 30.
    Anonymous (2016) Abaqus theory manual, dassault systems, Ver. 6.14 (digital version)Google Scholar
  31. 31.
    Ding Y, Liu X, Guo Y, Chen W (2011) Warm forming simulation of dual-phase steel tailor-welded blanks based on thermo-mechanical coupled method. Adv Mater Res 291-294:494–498.  https://doi.org/10.4028/www.scientific.net/AMR.291-294.494 CrossRefGoogle Scholar

Copyright information

© Springer-Verlag France SAS, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Forming Laboratory, Faculty of Mechanical EngineeringUniversity of LjubljanaLjubljanaSlovenia
  2. 2.Department of Manufacturing Engineering and Metal Forming Center of ExcellenceATILIM UniversityAnkaraTurkey

Personalised recommendations