Advertisement

Dynamic simulation on effect of flame arrangement on thermal process of regenerative reheating furnace

  • Ou Jian-ping  (欧俭平)Email author
  • Ma Ai-chun  (马爱纯)
  • Zhan Shu-hua  (詹树华)
  • Zhou Jie-min  (周孑民)
  • Xiao Ze-qiang  (萧泽强)
Article

Abstract

By analyzing the characteristics of combustion and billet heating process, a 3-D transient computer fluid dynamic simulation system based on commercial software CFX4.3 and some self-programmed codes were developed to simulate the thermal process in a continuous heating furnace using high temperature air combustion technology. The effects of different switching modes on injection entrancement of multi burners, combustion and billet heating process in furnace were analyzed numerically, and the computational results were compared with on-site measurement, which verified the practicability of this numerical simulation system. The results indicate that the flow pattern and distribution of temperature in regenerative reheating furnace with partial same-side-switching combustion mode are favorable to satisfy the high quality requirements of reheating, in which the terminal heating temperature of billets is more than 1 460 K and the temperature difference between two nodes is not more than 10 K. But since the surface average temperature of billets apart from heating zone is only about 1 350 K and continued heating is needed in soaking zone, the design and operation of current state are still needed to be optimized to improve the temperature schedule of billet heating. The distribution of velocity and temperature in regenerative reheating furnace with same-side-switching combustion mode cannot satisfy the even and fast heating process. The terminal heating temperature of billets is lower than that of the former case by 30 K. The distribution of flow and temperature can be improved by using cross-switching combustion mode, whose terminal temperature of billets is about 1 470 K with small temperature difference within 10 K.

Key words

high temperature air combustion reheating furnace switched combustion numerical simulation 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. [1]
    WU Zhen-kun, YANG Rui, WANG Jian, et al. Numerical simulation of a 3-D combustion flow field in a single chamber heating furnace with horizontal tubes[J]. Fire Safety Science, 2001, 10(4): 213–217. (in Chinese)Google Scholar
  2. [2]
    SHU Zheng-chuan, ZHU Tong. Numerical simulation investigation of the combustion system modification scheme for a cell pit furnace[J]. Journal of Engineering for Thermal Energy & Power, 2003, 18(6): 639–639. (in Chinese)Google Scholar
  3. [3]
    SHEN Bing-zhen, ZHOU Jin, HAN Zhi-qiang, et al. Numerical simulation on temperature field of steel slab in reheating furnace of hot rolling process[J]. Metallurgy Energy, 2002, 21(4): 24–28. (in Chinese)Google Scholar
  4. [4]
    OU Jian-ping, WU Dao-hong, XIAO Ze-qiang. Numerical simulation on the flow, combustion and heat transfer in regenerative reheating furnace[J]. Industrial Furnace, 2003, 25(1): 44–47. (in Chinese)Google Scholar
  5. [5]
    WU Cheng-bo, LIANG Xiao-ping, WANG Yu. Numerical simulation of flow and heat transfer in impinging heating furnace[J]. Iron and Steel, 1995, 30(3): 58–62. (in Chinese)Google Scholar
  6. [6]
    CHEN Ming-ye. The numerical value method of metal heating in continuous rolling mill heating furnace[J]. Journal of Shanghai University of Engineering Science, 1995, 9(2): 37–41. (in Chinese)MathSciNetGoogle Scholar
  7. [7]
    ZHANG Wei-jun. Study of Simulation, Optimization and Intelligence on the Control of Thermal Process for Reheating Furnace[D]. Shenyang: Northeastern University, 1998. (in Chinese)Google Scholar
  8. [8]
    YANG Wei-hong. Application of Computational Fluid Dynamics in Industrial Furnace Research and Development[D]. Changsha: Central South University, 2000. (in Chinese)Google Scholar
  9. [9]
    YUTAKA S. Regenerative burner heating system[C]// Proceedings of Beijing Symposium on High Temperature Air Combustion. Beijing, The Federation of Engineering Societies of Chinese Association for Science and Technology, 1999: 170–180.Google Scholar
  10. [10]
    HASEGAWA T, TANAKA R, NIIOKA T. High temperature air combustion contributing to energy saving and pollutant reduction in industrial furnace[C]// Proceedings of Beijing Symposium on High Temperature Air Combustion. Beijing, The Federation of Engineering Societies of Chinese Association for Science and Technology, 1999: 102–114.Google Scholar
  11. [11]
    WANG Ying-shi, FAN Wei-chen, ZHOU Li-xing, et al. Numerical Computation of Combustion[M]. Beijing: Science Press, 1986. (in Chinese)Google Scholar
  12. [12]
    TAO Wen-quan. Numerical Heat Transfer[M]. Xi’an: Xi’an Jiaotong University Press, 1988. (in Chinese)Google Scholar
  13. [13]
    AEA Technology Engineering Software Ltd. CFX4.4 User Documentation[M]. Harwell, 1999.Google Scholar
  14. [14]
    PATANKAR S V. ZHANG Zheng Tr. Numerical Heat Transfer and Fluid Flow[M]. Beijing: Science Press, 1984. (in Chinese)Google Scholar
  15. [15]
    MEI Chi. Simulation and Optimization of Nonferrous Metallurgical Furnaces[M]. Beijing: Metallurgical Industry Press, 2001. (in Chinese)Google Scholar
  16. [16]
    Editorial Committee of References of Industrial Furnace Design for Steel Plant. References of Industrial Furnace Design for Steel Plant (Vol.2)[M]. Beijing: Metallurgical Industry Press, 1979. (in Chinese)Google Scholar

Copyright information

© Published by: Central South University Press, Sole distributor outside Mainland China: Springer 2007

Authors and Affiliations

  • Ou Jian-ping  (欧俭平)
    • 1
    Email author
  • Ma Ai-chun  (马爱纯)
    • 1
  • Zhan Shu-hua  (詹树华)
    • 2
  • Zhou Jie-min  (周孑民)
    • 1
  • Xiao Ze-qiang  (萧泽强)
    • 1
  1. 1.School of Energy Science and EngineeringCentral South UniversityChangshaChina
  2. 2.General Iron and Steel Research InstituteBeijingChina

Personalised recommendations