Advertisement

Journal of Materials Engineering and Performance

, Volume 28, Issue 1, pp 485–497 | Cite as

The Effect of Chemical Composition and Processing Technology on the Microstructure, Texture and Earing Behavior of DR Tinplate

  • Xiao-fei Zheng
  • Lu-hai Liao
  • Yong-lin KangEmail author
  • Wei Liu
  • Quan-quan Qiu
Article
  • 27 Downloads

Abstract

The influence of alloying elements and processing technology on the microstructure, crystallographic texture and earing propensity has been investigated in two kinds of DR tinplate differing in Ti content: steel A, no Ti addition, and steel B 0.015% added. The cementite distribution, second-phase particles and the content of dissolved carbon and nitrogen atoms were obtained by SEM, TEM and XPS, respectively. Since the two steels develop both a partial 〈110〉//RD fiber and a {111}//ND fiber, the relative intensities of the several vital texture components seem to differ visibly. There are three types of strengthening mechanisms involved here: strengthening by grain size reduction, solution strengthening and strain hardening. That the tensile strength of steel B is greater than A implies the third mode plays a dominant role in the strength increasing for the DR tinplate. The crystallographic texture of materials not only results in a “preferential orientation” of the mechanical property, but also takes the primary responsibility for ears forming during drawing. Increasing the second cold-rolled reduction is not favorable to reduce the ear height, but this situation seems to be ameliorable. The average ears height of steel B is smaller than that of A, which demonstrated a low level of solute atoms and an ideal texture characteristic before deformation could alleviate the adverse effect caused by an elevated second cold reduction.

Keywords

DR tinplate crystallographic texture earing dissolved atoms titanium-alloyed steels 

References

  1. 1.
    E. Spišák, J. Slota, T. Kvačkaj, and A. Bobeni, The Influence of Tandem Mill Reduction on Double Reduced (DR) Tinplates Anisotropy, Metalurgija, 2006, 45(1), p 45–49Google Scholar
  2. 2.
    H.M. Alworth, J.T. Michalak, and S.A. Shei, The Effects of Second Cold Reduction on the Plastic Anisotropy, Crystallographic Texture and Earing Behavior of DR-9 Tin-Mill Product, J. Appl. Metalwork., 1987, 4(4), p 327–330Google Scholar
  3. 3.
    D. Raabe, Y. Wang, and F. Roters, Crystal Plasticity Simulation Study on the Influence of Texture on Earing in Steel, Comput. Mater. Sci., 2005, 34(3), p 221–234Google Scholar
  4. 4.
    M.R. Toroghinezhad, A.O. Humphreys, and J.J. Jonas, Effect of Chromium, Boron and Manganese Additions on the Deformation and Recrystallization Textures of Warm Rolled Low Carbon Steels, Trans. Iron Steel Inst. Jpn., 2003, 43(11), p 1842–1850Google Scholar
  5. 5.
    H. Inagaki, Fundamental Aspect of Texture Formation in Low Carbon Steel, ISIJ Int., 2007, 34(4), p 313–321Google Scholar
  6. 6.
    T. Yamashita and P. Hayes, Analysis of XPS Spectra of Fe 2+, and Fe 3+, Ions in Oxide Materials, Appl. Surf. Sci., 2008, 254(8), p 2441–2449Google Scholar
  7. 7.
    T. Fujii, F.M.F. De Groot, G.A. Sawatzky, F.C. Voogt, T. Hibma, and T.K. Okada, In Situ XPS Analysis of Various Iron Oxide Films Grown by NO2-Assisted Molecular-Beam Epitaxy, Phys. Rev. B, 1999, 59(4), p 3195Google Scholar
  8. 8.
    A. Ghosh, P. Modak, R. Dutta, and D. Chakrabarti, Effect of MnS Inclusion and Crystallographic Texture on Anisotropy in Charpy Impact Toughness of Low Carbon Ferritic Steel, Mater. Sci. Eng., A, 2015, 654, p 298–308Google Scholar
  9. 9.
    NIST online database. http://srdata.nist.gov/xps
  10. 10.
    R. Valentini, R. Ishak, M.D. Sanctis, and A. Solina, New Continuous Annealing Cycle for Producing DDQ Steel Sheets for Automotive Industries, La Metall. Ital., 2003, 95(4), p 51–56Google Scholar
  11. 11.
    H. Abe, T. Suzuki, and K. Takagi, Effects of the Size and Morphology of Cementite Particles on the Annealing Texture in Low-Carbon Aluminum-Killed Steel, Trans. Iron Steel Inst. Jpn., 1981, 21(2), p 100–108Google Scholar
  12. 12.
    R.K. Ray, J.J. Jonas, and R.E. Hook, Cold Rolling and Annealing Textures in Low Carbon and Extra Low Carbon Steels, Metall. Rev., 1994, 39(4), p 129–172Google Scholar
  13. 13.
    H. Inagaki, Fundamental Aspect of Texture Formation in Low Carbon Steel, ISIJ Int., 2007, 34(4), p 313–321Google Scholar
  14. 14.
    K. Koyama, H. Kato, and M. Nagumo, A Kinetics Model for Carbide Precipitation during Over-Aging in Continuous Annealing of Low-Carbon, Cold-Rolled Sheet Steels, Trans. Iron Steel Inst. Jpn., 2009, 72(7), p 823–830Google Scholar
  15. 15.
    T.O.D. Souza and V.T.L. Buono, Optimization of the Strain Aging Resistance in Aluminum Killed Steels Produced by Continuous Annealing, Mater. Sci. Eng., A, 2003, 354(1), p 212–216Google Scholar
  16. 16.
    M. Janošec, I. Schindler, V. Vodárek, J. Palát, S. Rusz, P. Suchánek, M. RÜŽIČKA, and E. Místecký, Microstructure and Mechanical Properties of Cold Rolled, Annealed HSLA Strip Steels, Arch. Civ. Mech. Eng., 2007, 7(2), p 29–38Google Scholar
  17. 17.
    L. Xiang, E.-B. Yue, D.D. Fan, and P. Zhao, Calculation of AIN and MnS Precipitation in Non-Oriented Electrical Steel Produced by CSP Process, J. Iron. Steel Res. Int., 2008, 15(5), p 88–94Google Scholar
  18. 18.
    S.K. Michelic, D. Loder, T. Reip, A.A. Barani, and C. Bernhard, Characterization of TiN, TiC and Ti(C, N) in Titanium-alloyed Ferritic Chromium Steels Focusing on the Significance of Different Particle Morphologies, Mater. Charact., 2015, 100, p 61–67Google Scholar
  19. 19.
    P. Ghosh, C. Ghosh, R.K. Ray, and D. Bhattacharjee, Precipitation Behavior and Texture Formation at Different Stages of Processing in an Interstitial Free High Strength Steel, Scr. Mater., 2008, 59(3), p 276–278Google Scholar
  20. 20.
    P. Ghosh, B. Bhattacharya, and R.K. Ray, Comparative Study of Precipitation Behavior and Texture Formation in Cold Rolled-batch Annealed and Cold Rolled-Continuous Annealed Interstitial Free High Strength Steels, Scr. Mater., 2007, 56(8), p 657–660Google Scholar
  21. 21.
    P. Ghosh, C. Ghosh, and R.K. Ray, Thermodynamics of Precipitation and Textural Development in Batch-Annealed Interstitial-Free High-Strength Steels, Acta Mater., 2010, 58(11), p 3842–3850Google Scholar
  22. 22.
    C. Jing, The Second-Phase Particles in Interstitial-Free(IF)Steels, Mater. Rev., 2005, 19, p 50–52Google Scholar
  23. 23.
    Y.L. Chen, Y. Wang, and A.M. Zhao, Precipitation of AlN and MnS in Low Carbon Aluminum-Killed Steel, J. Iron. Steel Res. Int., 2012, 19(4), p 51–56Google Scholar
  24. 24.
    Y. Kang, H. Yu, J. Fu, K. Wang, and Z. Wang, Morphology and Precipitation Kinetics of AlN in Hot Strip of Low Carbon Steel Produced by Compact Strip Production, Mater. Sci. Eng., A, 2003, 351(1), p 265–271Google Scholar
  25. 25.
    R. Radis and E. Kozeschnik, Kinetics of AlN Precipitation in Micro-Alloyed Steel, Modell. Simul. Mater. Sci. Eng., 2010, 18(5), p 055003Google Scholar
  26. 26.
    H. Kato, K. Kawasaki K, O. Kazuo, 689 Nucleation Sites of Cementites in Grains that Precipitate During Overaging of C.A.P.L. Process(PROPERTIES OF IRON AND STEEL, The 106th ISIJ Meeting Programme), Trans. Iron Steel Inst. Jpn., 1983, p 69Google Scholar
  27. 27.
    K. Ushioda and H. Tsuchiya, Fundamentals for Controlling the Microstructure and Properties of Cold Rolled and Continuously Annealed Sheet Steels, Trans. Indian Inst. Met., 2013, 66(5–6), p 655–664Google Scholar
  28. 28.
    K. Ushioda, N. Yoshinaga, and O. Akisue, Influences of Mn on Recrystallization Behavior and Annealing Texture Formation in Ultralow-Carbon and Low-Carbon Steels, Trans. Iron Steel Inst. Jpn., 2007, 34(1), p 85–91Google Scholar
  29. 29.
    I. Tsukatani, T. Inoue, and M. Sudo, Effects of Carbon and Manganese on the Recrystallization Texture of Cold-Rolled Steel Sheet, Trans. Iron Steel Inst. Jpn., 2009, 79(2), p 201–208Google Scholar
  30. 30.
    M. Takahashi and A. Okamoto, Effects of Heating Rate, N Contents, and Mn Contents on Recrystallization Texture of Aluminum-Killed Steel Sheets, Trans. Iron Steel Inst. Jpn., 2010, 61, p 2246–2262Google Scholar
  31. 31.
    R.K. Ray and J.J. Jonas, Transformation Textures in Steels, Metall. Rev., 1994, 35(1), p 1–36Google Scholar
  32. 32.
    H. Inagaki, Effect of Ti on the Development of Rolling Textures in High Purity Iron, Textures Microstruct., 1988, 8, p 173–189Google Scholar
  33. 33.
    J. Jia, L. Dai, S. Yuan, X. Song, Z. Yuan, and X. Chai, Effects of P and Ti on 111 Plane Texture in High Strength IF Steels, Chin. J. Mater. Res., 2011, 25(6), p 656–660Google Scholar
  34. 34.
    H. Yoshida, K. Okuda, H. Kawabe, T. Urabe, Y. Tanaka, Y. Hosoya, Effect of Niobium Addition on the Texture Formation of High Strength Cold-Rolled Low Carbon Steel Sheets, Mater. Sci. Forum, 2007, 558–559, p 425–430Google Scholar
  35. 35.
    M. Černík, R. Gburík, L. Hrabčáková, P. Vranec, Texture Analysis of Tinplate Steel and its Application in Production of Double Reduced High Strength Tinplate Grades with Controlled Earing Properties, 2015, (4), p 12108–12111Google Scholar
  36. 36.
    W.D. Callister, D.G. Rethwisch, Materials Science and Engineering SI version, -8/E, Wiley, 2011Google Scholar
  37. 37.
    J. Asensio, G. Romano, V.J. Martinez, J.I. Verdeja, and J.A. Pero-Sanz, Ferritic Steels: Optimization of Hot-Rolled Textures through Cold Rolling and Annealing, Mater. Charact., 2001, 47(2), p 119–127Google Scholar
  38. 38.
    S. Li and X. Zhang, A New Method for Predicting Earing Tendency of Textured Sheets, Acta Metall. Sin., 1996, 32(8), p 884–890Google Scholar
  39. 39.
    R. Saha, R.K. Ray, and D. Bhattacharjee, Attaining Deep Drawability and Non-Earing Properties in Ti+Nb Interstitial-Free Steels through Double Cold Rolling and Annealing, Scr. Mater., 2007, 57(3), p 257–260Google Scholar

Copyright information

© ASM International 2018

Authors and Affiliations

  • Xiao-fei Zheng
    • 1
  • Lu-hai Liao
    • 1
  • Yong-lin Kang
    • 1
    Email author
  • Wei Liu
    • 2
  • Quan-quan Qiu
    • 1
  1. 1.University of Science and Technology Beijing, School of Materials and EngineeringBeijingChina
  2. 2.Shougang Jingtang United Iron and Steel Co LtdTangshanChina

Personalised recommendations