Evolution of Microstructure in a Low-Si Micro-alloyed Steel Processed Through One-Step Quenching and Partitioning
- 138 Downloads
An attempt has been made in the current study to investigate the possibility of austenite retention in 0.5 wt pct Si steel without Al, processed through the one-step Q&P technique. The XRD and microstructural analysis confirmed austenite retention (maximum of 5.73 ± 0.16 vol pct), which showed thin film and blocky morphologies. The experimental amount of retained austenite was found to increase with the increasing quench temperature; however, it was almost independent of partitioning time. The carbon content in the retained austenite did not show any significant variation, after Q&P treatment for different time–temperature combinations. The hardness was found to be sensitive to quench temperature than the partitioning time.
The authors gratefully acknowledge the financial support of Tata Steel Ltd., Jamshedpur for this research. The authors would also like to thank the Director, CSIR-NML, and Tata Steel management for their kind encouragement and permission to publish this work.
- 2.M.C. Somani, D.A. Porter, L.P. Karjalainen, and D.K. Misra: Inter. J. Metall. Eng., 2013, vol. 2(2), pp. 154-60.Google Scholar
- 12.T. Nyyssönen, M. Somani, P. Peura, and V.-T. Kuokkala: Proc. of the ASME 2013 International Mechanical Engineering Congress and Exposition, San Diego, California, USAGoogle Scholar
- 16.E. De Moor, S. Lacroix, L. Samek, J. Penning, and J.G. Speer: The 3rd Inter. Conf. on Advanced Structural Steels, Gyeongju, Korea, August 22–24, 2006.Google Scholar
- 17.P.C. Wolfram: M.S. Thesis, Colorado School of Mines, Golden, Co, 2013.Google Scholar
- 20.G.R. Speich: Trans. Metall. Soc. AIME, 1969, vol. 245, pp. 2553-64Google Scholar
- 24.L. Suarez, J. Schneider, and Y. Houbaert: Defect and Diffusion Forum, 2008, vol. 273-276, pp. 655-60.Google Scholar
- 26.H. Kong, Q. Chao, M.H. Cai, E.J. Pavlina, B. Rolfe, P.D. Hodgson, and H. Beladi: Metall. Mater. Trans. A, 2018, vol. 49, pp. 1509-19.Google Scholar
- 31.E. De Moor, J. Penning, C. Fojer, A.J. Clarke, and J.G. Speer: Inter. Conf. on New Developments in Advanced High-Strength Sheet Steels, Orlando, FL, 2008, pp. 199–207.Google Scholar
- 35.A.M. Streicher, J.G. Speer, D.K. Matlock, and B.C. De Cooman: Proc. of Int. Conf. on Advanced High Strength Sheet Steels for Automotive Applications, Winter Park, US, Jun 6-9, 2004, pp. 51-62.Google Scholar
- 41.J. Dearden and H. O’Neill: Trans. Inst. Weld, 1940, vol. 3, pp. 203-14.Google Scholar
- 44.J.G. Speer, A.M. Streicher, D.K. Matlock, F. Rizzo, and G. Krauss: Austenite Formation and Decomposition, TMS/ISS, warrendale (2003) 505-22.Google Scholar
- 45.K.W. Andrews: J. of the Iron and Steel Inst., 1965, vol. 203, pp. 721-27.Google Scholar