# A Subgrid-Scale Model for Turbulent Flow in Porous Media

- 315 Downloads

## Abstract

Given the analogy between the filtered equations of large eddy simulation and volume-averaged Navier–Stokes equations in porous media, a subgrid-scale model is presented to account for the residual stresses within the porous medium. The proposed model is based on the kinetic energy balance of the filtered velocity field within a pore; hence, when using the model, numerical simulations of the turbulent flow in the pores are not required. The accuracy of the model is validated with available data in the literature on turbulent flow through packed beds and staggered arrangement of square cylinders. The validation yields that the model successfully captures the effect of the pore-scale turbulent motion. The model is then used to study turbulent flow in a wall-bounded porous media to assess its accuracy.

## Keywords

Turbulence Porous media Volume average LES Subgrid-scale model## 1 Introduction

Fluid flow through porous media takes place in many practical applications, such as heat exchangers, cooling of electronic components, biological systems, geothermal engineering, solid matrix heat exchangers, enhanced oil recovery, thermal insulation, canopy flow, flow over vegetation, crop fields, grain storage, drying processes and chemical reactors (De Lemos 2009; Ljung et al. 2012; Vafai 2015). High Reynolds numbers, Re, in many of the aforementioned applications have motivated researchers to take into account the effects of turbulence within the pores (Dybbs and Edwards 1984; Khayamyan et al. 2017a, b; Larsson et al. 2018; Seguin et al. 1998). To exemplify, Dybbs and Edwards (1984) categorized the flow into four regimes of pore Re, \( \text{Re}_{p} \), according to: Darcian regime (\( \text{Re}_{p} < 1 \)), Forchheimer regime (\( 1 - 10 < \text{Re}_{p} < 150 \)), unsteady-laminar (\( 150 < \text{Re}_{p} < 300 \)) and turbulent regimes (\( \text{Re}_{p} > 300 \)) based on results from an experimental study of flow through beds of rods, spheres and complex rod bundles. However, experimental measurement and direct numerical simulation of turbulent flow inside the pores in random systems are tricky due to the complexity of the pore structures and their small size. This also implies that the computational effort required to exactly represent these systems is large especially for turbulent flow. A method to circumvent this problem is to replace the complex system of pores with a homogeneous medium with averaged properties using volume averaging techniques (VAT) (Whitaker 2013). Originating from this approach, several versions of macroscopic models are proposed in the literature. In most of these approaches, time averaging is used to model turbulent effects and volume averaging to homogenously present the morphology of the porous medium (Teruel 2009a). It should also be noted that during such averaging processes, extra terms appear that often have to be modeled using experimental measurement or numerical simulation of turbulent flow within the pores. Lee and Howell (1987), Antohe and Lage (1997), Getachew et al. (2000), and Lien and Leschziner (1994) are among those who proposed a two-equation macroscopic turbulence model by Reynolds averaging the volume-averaged Navier–Stokes (VANS) equations. According to Nield (2001), their strategy leads to a model of the macroscale Reynolds stresses, while the intra-pore stresses do not come into play. Another group of researchers such as Nakayama and Kuwahara (1999, 2008), Pedras and de Lemos (2001) and Nikora et al. (2007) applied the volume averaging operator to the Reynolds averaged equations in order to macroscopically model the turbulent flow. As a result, the models derived take into account the intra-pore turbulence in addition to its macroscopic effects. It is shown by Pedras and de Lemos (2001) that the order of time and volume averaging is not important except regarding the turbulence kinetic energy. In addition to the two-equation macroscopic turbulence models mentioned above, other turbulence models have been reported in the literature such as the zero equation model by Masuoka and Takatsu (1996), the one-equation model developed by Alvarez et al. (2003), multi-scale four-equation eddy viscosity model of Kuwata et al. (2014) and Kuwata and Suga’s (2013) based on a second moment closure. Two-equation turbulence models have, however, gained the most attention in the literature similar to their clear fluid counterparts. As compared to clear fluid flow, the transport equations of turbulent kinetic energy (TKE) and dissipation rate equations for porous media flow include additional terms which quantify the effects of the solid matrix on the turbulent parameters. Different correlations have been proposed in the literature to model these extra production terms (Nakayama and Kuwahara 1999, 2008; Pedras and de Lemos 2001). A comparison of the extra terms in TKE and dissipation rate equations from different models is presented in Guo et al. (2006). By a comparison of the results to experimental data, it is shown that the Nakayama and Kuwahara’s (1999) (N–K) model produces more reasonable results as compared to the other models investigated in their study. The original N–K model (Nakayama and Kuwahara 1999) and its modifications have been extensively used in different applications (Chandesris et al. 2006; Hoffmann 2004; Jouybari et al. 2018).

In spite of the extensive works mentioned above on turbulent flow in porous media, much is still unknown including an uncertainty on the existence of large structures in the flow. Several researches have reported that the pore size of the porous medium sets the upper limit of the size of turbulent eddies since these structures become confined in the pores (Jin and Kuznetsov 2017; Jin et al. 2015; Nield 1991; Uth et al. 2016). However, Uth et al. (2016) reported that large structures may exist in porous media with very large porosities equal to 0.995 which is discussed to be unrealistic by Jin and Kuznetsov (2017). Also, direct numerical simulations (DNS) performed by Chandesris et al. (2013) and Breugem and Boersma (2005) for turbulent flow in a channel partially filled with a porous medium showed that large structures forming above a porous–fluid interface penetrate into the upper layer of the porous bed. In order to capture these large structures and considering the analogy between the filtered equations of large eddy simulations (LES) with VANS equations in porous media, Breugem et al. (2006) simulated turbulent flow over and inside a packed bed in a channel using LES. The filter size was considered sufficiently small so that the subfilter-scale dispersion in the channel region was negligible in their study. Breugem et al. (2006) showed that the residual stresses in porous media are small for their case. Obviously, this assumption may not be valid when the Re in the pores is so high that turbulent effects are not negligible. LES modeling of turbulent flow within and over forests as porous media have also been previously reported in several studies including Dwyer et al. (1997), Kanda and Hino (1994), Shaw and Patton (2003) and Watanabe (2004).

Based on the introduction above, the aim of the present study is to present a subgrid-scale model for the intra-pore residual stresses that emerge in the VANS equations. To this end, a model is proposed based on filtered kinetic energy balance within the pores. One advantage with this model is that prior numerical simulations of turbulent flow within the pores are not required in order to close the macroscopic equations. For cases where large structures are present, the VANS equations directly represent the larger motions, whereas the residual motions in the REV are captured with the subgrid-scale model. Otherwise, if there is microscopic turbulence and no macroscopic turbulence, the subgrid-scale model accounts for the turbulence effects within the pores and the VANS equations will be solved in the same way as in laminar flows. Therefore, no turbulence model is used for the macroscopic turbulence and no extra equation is solved for turbulent quantities such as TKE and dissipation rate.

## 2 Governing Equations

### 2.1 Filtered Equations

*residual stress*model so that \( \tau_{ij}^{r} = \overline{{U_{i} U_{j} }} - \overline{U}_{i} \overline{U}_{j} \) can be evaluated. As mentioned in Pope (2000), the filter type and width, \( \Delta \), do not appear explicitly in Eqs. (1) and (2). They indirectly affect the filtered velocity through the model for the residual stresses. Several subgrid-scale models are proposed for \( \tau_{ij}^{r} \) in the literature to close the filtered equations. The model proposed by Smagorinsky is the simplest one which is based on a linear viscosity model (Pope 2000), as:

According to Pope (2000), the size of Δ should be selected such that at least 80% of energy is resolved.

### 2.2 Volume-Averaged Equations for Flows in Porous Media

*of a REV with a volume of*

**x***V*, \( \varvec{y = r} - \varvec{x} \) is the relative position, \( \gamma \) is the phase indicator being 1 in the fluid phase and 0 in the solid phase and

*m*is the weighting function. A schematic of a REV for a random porous media is shown in Fig. 1 for which the REV is a sphere with radius \( r_{0} \) where

*m*is defined as:

*subfilter*-

*scale*\( \varphi \) in LES terminology. Also, \( {{\left\langle \varphi \right\rangle = \left\langle \varphi \right\rangle^{\varepsilon } } \mathord{\left/ {\vphantom {{\left\langle \varphi \right\rangle = \left\langle \varphi \right\rangle^{\varepsilon } } \varepsilon }} \right. \kern-0pt} \varepsilon } \) in Eq. (8) is the intrinsic average of \( \varphi \) and \( \varepsilon \) denotes the porosity of the porous medium, which is defined as:

#### 2.2.1 Modeling of Subfilter-Scale Stress in Porous Media

Extra source terms in turbulence equations

References | \( S_{\text{k}} = \varepsilon_{{{\text{d}}\infty }} \) | \( S_{\varepsilon } = \frac{{\varepsilon_{{{\text{d}}\infty }}^{2} }}{{k_{\infty } }} \) | \( \upsilon_{r\varepsilon } /\upsilon \) |
---|---|---|---|

N–K (Nakayama and Kuwahara 1999) | \( k_{\infty } = 3.7\varphi^{{{3 \mathord{\left/ {\vphantom {3 2}} \right. \kern-0pt} 2}}} \left( {1 - \varphi } \right)\left\langle {\bar{U}_{j} } \right\rangle \left\langle {\bar{U}_{j} } \right\rangle^{f} \) \( \varepsilon_{{{\text{d}}\infty }} = 39\varphi^{2} \left( {1 - \varphi } \right)^{{{5 \mathord{\left/ {\vphantom {5 2}} \right. \kern-0pt} 2}}} \frac{{\left( {\left\langle {\bar{U}_{j} } \right\rangle \left\langle {\bar{U}_{j} } \right\rangle } \right)^{{{3 \mathord{\left/ {\vphantom {3 2}} \right. \kern-0pt} 2}}} }}{d} \) | \( \frac{{\upsilon_{r\varepsilon } }}{\upsilon } = 0.0316\frac{\varepsilon }{{\sqrt {1 - \varepsilon } }}\frac{{\left\langle {\bar{U}_{j} } \right\rangle d}}{\upsilon } \) | |

N–K (Nakayama and Kuwahara 2008) | \( k_{\infty } = 0.673\left\langle {\bar{U}_{j} } \right\rangle \left\langle {\bar{U}_{j} } \right\rangle \) \( \varepsilon_{{{\text{d}}\infty }} = \frac{{1.75\left( {1 - \varphi } \right)}}{\varphi }\frac{{\left( {\left\langle {\bar{U}_{j} } \right\rangle \left\langle {\bar{U}_{j} } \right\rangle } \right)^{{{3 \mathord{\left/ {\vphantom {3 2}} \right. \kern-0pt} 2}}} }}{d} \) | \( \frac{{\upsilon_{r\varepsilon } }}{\upsilon } = 0.0233\frac{\varepsilon }{1 - \varepsilon }\frac{{\left\langle {\bar{U}_{j} } \right\rangle d}}{\upsilon }\quad {\text{Packed}}\;{\text{bed}} \) \( \frac{{\upsilon_{r\varepsilon } }}{\upsilon } = 0.0099\left( {\frac{{\left\langle {\bar{U}_{j} } \right\rangle d_{\text{p}} }}{\upsilon }} \right)^{{{3 \mathord{\left/ {\vphantom {3 4}} \right. \kern-0pt} 4}}} \quad {\text{Channels}}\;{\& }\;{\text{Pipes}} \) |

It can be assumed that in the Smagorinsky model for clear fluid, the second term on the RHS of Eq. (17) can be neglected due to its minor effect on the residual stresses as compared to the first term. However, as mentioned by Nakayama and Kuwahara (2008), the characteristics filtered strain rate (the first term on the RHS of Eq. (17) is negligible compared to the characteristics residual strain rate (the second term on the RHS of Eq. (17)) for turbulent flow in porous media.

##### 2.2.1.1 Evaluation of Characteristics Residual Strain Rate

## 3 Evaluation of \( \upsilon_{r\varepsilon }^{{}} \) for Two Types of Porous Media

### 3.1 Turbulent Flow in a Packed Bed

*D,*the following expressions may be formed (Nakayama and Kuwahara 2008; Seguin et al. 1998):

*d*

_{p}is the pore diameter. Substituting these quantities in Eq. (21) yields the subfilter scale stress, as:

### 3.2 Turbulent Flow in Staggered Arrangement of Square Cylinders

*D*(Fig. 3),

*K*and

*b*are defined as (Kuwahara et al. 2006):

## 4 Assessment of the Present Model for Turbulent Flow in Wall-Bounded Porous Media

*x*direction are considered to be periodic. Advection terms are discretized using bounded central difference method and second-order Euler backward method is used for the discretization of unsteady terms. The numerical simulations are carried out in Ansys CFX where the present subgrid-scale model is added to include the turbulence effects within the pores. The LES model is selected to capture any possible large structures in the channel. A grid independency study is carried out and it is observed that the velocity profile does not change for an increase in elements from approximately 3200 to 6400. Therefore, 3200 elements are selected for the simulations. Figure 6 shows a comparison between the normalized velocity profiles calculated from the present model and DNS case A in Jin and Kuznetsov 2017. This case is a porous medium with \( {s \mathord{\left/ {\vphantom {s d}} \right. \kern-0pt} d} = 0.75 \), \( \varepsilon = 0.69 \), \( {H \mathord{\left/ {\vphantom {H s}} \right. \kern-0pt} s} = 40 \) and \( \text{Re} = {{u_{D} d} \mathord{\left/ {\vphantom {{u_{D} d} \upsilon }} \right. \kern-0pt} \upsilon } = 257 \) which correspond to channel Re of \( \text{Re} = {{u_{D} 2H} \mathord{\left/ {\vphantom {{u_{D} 2H} \upsilon }} \right. \kern-0pt} \upsilon } = 15400 \). The results are obtained at the large time interval for which the time averaging velocity is independent of the time of starting the averaging process. This time interval has been checked for different starting times of averaging process in order to verify the independency of the final results. It should be noted that no large structures are observed in the present simulations which are in agreement with Jin and Kuznetsov (2017), Jin et al. (2015), Nield (1991) and Uth et al. (2016). Therefore, the main turbulent effects are mainly due to turbulence within the pores. As can be observed in Fig. 6, the present results are in a good agreement with the normalized velocity calculated from the DNS data in Jin and Kuznetsov (2017). As a final comparison, Fig. 7 illustrates \( {{\partial \left( {\varepsilon \left\langle {u^{\prime}v^{\prime}} \right\rangle } \right)} \mathord{\left/ {\vphantom {{\partial \left( {\varepsilon \left\langle {u^{\prime}v^{\prime}} \right\rangle } \right)} {\partial y}}} \right. \kern-0pt} {\partial y}} \) as calculated from DNS results in Jin and Kuznetsov (2017), model results in Jin and Kuznetsov (2017) which are calculated from \( \upsilon_{r\varepsilon } = {{c_{\mu } \left\langle k \right\rangle^{2} } \mathord{\left/ {\vphantom {{c_{\mu } \left\langle k \right\rangle^{2} } {\left\langle {\varepsilon_{\text{d}} } \right\rangle }}} \right. \kern-0pt} {\left\langle {\varepsilon_{\text{d}} } \right\rangle }} \) assuming that the TKE, \( k \), and dissipation rate, \( \varepsilon_{\text{d}} \), are those calculated from DNS results and the present results from Eq. (25). As can be seen, the present results are in a good agreement with the model results in Jin and Kuznetsov (2017). Due to negligible velocity gradient in most of the channel height, a small amount of Reynolds stress is calculated from eddy viscosity except for the region close to the wall where the velocity gradient takes large values. Consequently, both of the present model results and model results of Jin and Kuznetsov (2017) increase close to the wall which agree reasonably well with the DNS data of Jin and Kuznetsov (2017).

## 5 Conclusion

Due to the similarity between the filtered Navier–stokes and VANS equations within porous media, it is found that these equations may be used to directly solve the large structures of turbulence provided that a proper model for the subgrid-scale is adopted. To this end, the filtered kinetic energy within the pores in a REV is re-examined to reach a balance between the production and dissipation terms in the pores. As a result, a subfilter-scale model for the residual stresses in porous media is presented without a need of doing a prerequisite numerical simulation of turbulent flow within the pores. The present model is validated with numerical and experimental results from the literature for packed beds and staggered array of square cylinders. The present model is also used to model turbulent flow in a wall-bounded porous media. Although no large structures are observed in the domain, the present subgrid-scale model successfully predicts the level of subgrid Reynolds stress close to the wall and within the porous medium.

## Notes

### Acknowledgements

The project was funded by the Kempe Foundations and Luleå University of Technology, and the work was carried out under the Grant 2017-04390 from the Swedish Research Council.

## References

- Alvarez, G., Bournet, P.-E., Flick, D.: Two-dimensional simulation of turbulent flow and transfer through stacked spheres. Int. J. Heat Mass Transf.
**46**(13), 2459–2469 (2003)CrossRefGoogle Scholar - Antohe, B., Lage, J.: A general two-equation macroscopic turbulence model for incompressible flow in porous media. Int. J. Heat Mass Transf.
**40**(13), 3013–3024 (1997)CrossRefGoogle Scholar - Bey, O., Eigenberger, G.: Fluid flow through catalyst filled tubes. Chem. Eng. Sci.
**52**(8), 1365–1376 (1997)CrossRefGoogle Scholar - Breugem, W., Boersma, B.: Direct numerical simulations of turbulent flow over a permeable wall using a direct and a continuum approach. Phys. Fluids
**17**(2), 025103 (2005)CrossRefGoogle Scholar - Breugem, W., Boersma, B., Uittenbogaard, R.: The influence of wall permeability on turbulent channel flow. J. Fluid Mech.
**562**, 35–72 (2006)CrossRefGoogle Scholar - Chandesris, M., d’Hueppe, A., Mathieu, B., Jamet, D., Goyeau, B.: Direct numerical simulation of turbulent heat transfer in a fluid-porous domain. Phys. Fluids
**25**(12), 125110 (2013)CrossRefGoogle Scholar - Chandesris, M., Serre, G., Sagaut, P.: A macroscopic turbulence model for flow in porous media suited for channel, pipe and rod bundle flows. Int. J. Heat Mass Transf.
**49**(15–16), 2739–2750 (2006)CrossRefGoogle Scholar - De Lemos, M.J.: Turbulent flow around fluid–porous interfaces computed with a diffusion-jump model for k and ε transport equations. Transp. Porous Media
**78**(3), 331–346 (2009)CrossRefGoogle Scholar - Dwyer, M.J., Patton, E.G., Shaw, R.H.: Turbulent kinetic energy budgets from a large-eddy simulation of airflow above and within a forest canopy. Bound. Layer Meteorol.
**84**(1), 23–43 (1997)CrossRefGoogle Scholar - Dybbs, A., Edwards, R.: A new look at porous media fluid mechanics—Darcy to turbulent. In: Fundamentals of Transport Phenomena in Porous Media, pp. 199–256. Springer, Berlin (1984)Google Scholar
- Fluent, A.: 16.0, Ansys Fluent User’s Guide. ANSYS. In. Inc (2015)Google Scholar
- Getachew, D., Minkowycz, W., Lage, J.: A modified form of the κ–ε model for turbulent flows of an incompressible fluid in porous media. Int. J. Heat Mass Transf.
**43**(16), 2909–2915 (2000)CrossRefGoogle Scholar - Guo, B., Yu, A., Wright, B., Zulli, P.: Simulation of turbulent flow in a packed bed. Chem. Eng. Technol.
**29**(5), 596–603 (2006)CrossRefGoogle Scholar - Hoffmann, M.R.: Application of a simple space-time averaged porous media model to flow in densely vegetated channels. J. Porous Media
**7**(3) (2004)Google Scholar - Jin, Y., Kuznetsov, A.: Turbulence modeling for flows in wall bounded porous media: an analysis based on direct numerical simulations. Phys. Fluids
**29**(4), 045102 (2017)CrossRefGoogle Scholar - Jin, Y., Uth, M.-F., Kuznetsov, A., Herwig, H.: Numerical investigation of the possibility of macroscopic turbulence in porous media: a direct numerical simulation study. J. Fluid Mech.
**766**, 76–103 (2015)CrossRefGoogle Scholar - Jouybari, N.F., Maerefat, M., Lundström, T.S., Nimvari, M.E., Gholami, Z.: A general macroscopic model for turbulent flow in porous media. J. Fluids Eng.
**140**(1), 011201 (2018)CrossRefGoogle Scholar - Kanda, M., Hino, M.: Organized structures in developing turbulent flow within and above a plant canopy, using a large eddy simulation. Bound. Layer Meteorol.
**68**(3), 237–257 (1994)CrossRefGoogle Scholar - Khayamyan, S., Lundström, T.S., Gren, P., Lycksam, H., Hellström, J.G.I.: Transitional and turbulent flow in a bed of spheres as measured with stereoscopic particle image velocimetry. Transp. Porous Media
**117**(1), 45–67 (2017a)CrossRefGoogle Scholar - Khayamyan, S., Lundström, T.S., Hellström, J.G.I., Gren, P., Lycksam, H.: Measurements of transitional and turbulent flow in a randomly packed bed of spheres with particle image velocimetry. Transp. Porous Media
**116**(1), 413–431 (2017b)CrossRefGoogle Scholar - Kuwahara, F., Yamane, T., Nakayama, A.: Large eddy simulation of turbulent flow in porous media. Int. Commun. Heat Mass Transf.
**33**(4), 411–418 (2006)CrossRefGoogle Scholar - Kuwata, Y., Suga, K.: Modelling turbulence around and inside porous media based on the second moment closure. Int. J. Heat Fluid Flow
**43**, 35–51 (2013)CrossRefGoogle Scholar - Kuwata, Y., Suga, K., Sakurai, Y.: Development and application of a multi-scale k–ε model for turbulent porous medium flows. Int. J. Heat Fluid Flow
**49**, 135–150 (2014)CrossRefGoogle Scholar - Larsson, I.S., Lundström, T.S., Lycksam, H.: Tomographic PIV of flow through ordered thin porous media. Exp. Fluids
**59**(6), 96 (2018)CrossRefGoogle Scholar - Lee, K., Howell, J.: Forced convective and radiative transfer within a highly porous layer exposed to a turbulent external flow field. In: Proceedings of the 1987 ASME-JSME Thermal Engineering Joint Conf 1987, pp. 377–386Google Scholar
- Lien, F., Leschziner, M.: A general non-orthogonal collocated finite volume algorithm for turbulent flow at all speeds incorporating second-moment turbulence-transport closure, Part 1: computational implementation. Comput. Methods Appl. Mech. Eng.
**114**(1–2), 123–148 (1994)CrossRefGoogle Scholar - Ljung, A.-L., Frishfelds, V., Lundström, T.S., Marjavaara, B.D.: Discrete and continuous modeling of heat and mass transport in drying of a bed of iron ore pellets. Drying Technol.
**30**(7), 760–773 (2012)CrossRefGoogle Scholar - Masuoka, T., Takatsu, Y.: Turbulence model for flow through porous media. Int. J. Heat Mass Transf.
**39**(13), 2803–2809 (1996)CrossRefGoogle Scholar - Nakayama, A., Kuwahara, F.: A macroscopic turbulence model for flow in a porous medium. J. Fluids Eng.
**121**(2), 427–433 (1999)CrossRefGoogle Scholar - Nakayama, A., Kuwahara, F.: A general macroscopic turbulence model for flows in packed beds, channels, pipes, and rod bundles. J. Fluids Eng.
**130**(10), 101205 (2008)CrossRefGoogle Scholar - Nield, D.: The limitations of the Brinkman-Forchheimer equation in modeling flow in a saturated porous medium and at an interface. Int. J. Heat Fluid Flow
**12**(3), 269–272 (1991)CrossRefGoogle Scholar - Nield, D.: Alternative models of turbulence in a porous medium, and related matters. J. Fluids Eng.
**123**(4), 928–931 (2001)CrossRefGoogle Scholar - Nikora, V., McEwan, I., McLean, S., Coleman, S., Pokrajac, D., Walters, R.: Double-averaging concept for rough-bed open-channel and overland flows: theoretical background. J. Hydraul. Eng.
**133**(8), 873–883 (2007)CrossRefGoogle Scholar - Pedras, M.H., de Lemos, M.J.: Macroscopic turbulence modeling for incompressible flow through undeformable porous media. Int. J. Heat Mass Transf.
**44**(6), 1081–1093 (2001)CrossRefGoogle Scholar - Pope, S.B., Pope, S.B.: Turbulent Flows. Cambridge University Press, Cambridge (2000)CrossRefGoogle Scholar
- Qin, C., Hassanizadeh, S.: A new approach to modelling water flooding in a polymer electrolyte fuel cell. Int. J. Hydrog. Energy
**40**(8), 3348–3358 (2015)CrossRefGoogle Scholar - Seguin, D., Montillet, A., Comiti, J., Huet, F.: Experimental characterization of flow regimes in various porous media—II: transition to turbulent regime. Chem. Eng. Sci.
**53**(22), 3897–3909 (1998)CrossRefGoogle Scholar - Shaw, R.H., Patton, E.G.: Canopy element influences on resolved-and subgrid-scale energy within a large-eddy simulation. Agric. For. Meteorol.
**115**(1–2), 5–17 (2003)CrossRefGoogle Scholar - Teruel, F.E.: A new turbulence model for porous media flows. Part I: constitutive equations and model closure. Int. J. Heat Mass Transf.
**52**(19–20), 4264–4272 (2009a)CrossRefGoogle Scholar - Teruel, F.E.: A new turbulence model for porous media flows. Part II: analysis and validation using microscopic simulations. Int. J. Heat Mass Transf.
**52**(21–22), 5193–5203 (2009b)CrossRefGoogle Scholar - Uth, M.-F., Jin, Y., Kuznetsov, A., Herwig, H.: A direct numerical simulation study on the possibility of macroscopic turbulence in porous media: effects of different solid matrix geometries, solid boundaries, and two porosity scales. Phys. Fluids
**28**(6), 065101 (2016)CrossRefGoogle Scholar - Vafai, K.: Handbook of Porous Media. CRC Press, Boca Raton (2015)CrossRefGoogle Scholar
- Versteeg, H.K., Malalasekera, W.: An Introduction to Computational Fluid Dynamics: The Finite Method. Pearson Prentice Hall, Upper Saddle River (2007)Google Scholar
- Watanabe, T.: Large-eddy simulation of coherent turbulence structures associated with scalar ramps over plant canopies. Bound. Layer Meteorol.
**112**(2), 307–341 (2004)CrossRefGoogle Scholar - Whitaker, S.: The Method of Volume Averaging, vol. 13. Springer, Berlin (2013)Google Scholar

## Copyright information

**Open Access**This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.