Advertisement

Powder Metallurgy and Metal Ceramics

, Volume 57, Issue 7–8, pp 458–464 | Cite as

Zirconia–Titanium Interface in Ceramic Based Composite

  • P. Lada
  • A. Miazga
  • P. Bazarnik
  • K. Konopka
  • M. Szafran
REFRACTORY AND CERAMIC MATERIALS
  • 7 Downloads

One of the important aspects in the preparation of composite materials is the possibility of reaction between used components. In the case of composite of ZrO2–Ti system, it could be the reaction between zirconia and titanium particles during sintering process. In this work ZrO2/Ti interface at 3Y-ZrO2–10 vol.% Ti composites was analyzed. The composites were prepared by slip casting method. Sintering process was carried out at 1450°C in the inert atmosphere of argon. The sinters were prepared for SEM and STEM microscope observations by polishing and ion milling. The chemical analysis was conducted by EDS. The bonding between Ti particle and ZrO2 matrix was continuous. XRD analysis, microscopic observations and chemical analysis showed the limited diffusion between components. The creation of new phases at ZrO2/Ti interface was not revealed.

Keywords

zirconium oxide titanium composite interface 

Notes

Acknowledgements

The work was carried out within the frame of the project financed by the National Center of Science (NCN), project DEC-2013/11/B/ST8/00309.

References

  1. 1.
    A.S. Al-Radha, D. Dymock, C. Younes, and D. O’Sullivan, “Surface properties of titanium and zirconia dental implant materials and their effect on bacterial adhesion,” Journal of dentistry, 40, No. 2, 146–153 (2012).CrossRefGoogle Scholar
  2. 2.
    P. Miranzo, and M.I. Osendi, “Thermal conductivity of a ZrO2–Ni functionally graded coatings,” Scr. Mater., 58, No. 11, 973–976 (2008).CrossRefGoogle Scholar
  3. 3.
    T. Wager, R. Kirchheim, and M. Ruhle, “Chemical reaction at metal/ceramic interfaces during diffusion bonding,” Acta Metall. Mater., 43, No. 3, 1053–1063 (1995).CrossRefGoogle Scholar
  4. 4.
    M.C. Munoz, J.I. Beltran, S. Gallego, and J.I. Cerdá, “Adhesion at metal–ZrO2 interfaces,” Surf. Sci. Reports, 61, No. 6, 303–344 (2006).CrossRefGoogle Scholar
  5. 5.
    T. Fujii, K. Tohgo, H. Araki, K. Wakazono, M. Ishikura, and Y. Shimamuraand, “Effect of material composition on mechanical properties of ceramic-metal composite materials,” Key Eng. Mater., 462–463, 100–105 (2011).CrossRefGoogle Scholar
  6. 6.
    B.C. Weber, H.J. Garrett, F.A. Mauer, and M.A. Schwartz, “Observations on the stabilization of zirconia,” J. Am. Ceram. Soc., 39, No. 6, 197–206 (1956).CrossRefGoogle Scholar
  7. 7.
    R. Ruh, “Reaction of zirconia and titanium at elevated temperatures,” J. Am. Ceram. Soc., 46, No. 7, 301–307 (1963).CrossRefGoogle Scholar
  8. 8.
    R. Ruh, N.M. Tallan, and H.A. Lipsitt, “Effect of metal additions on the microstructure of zirconia,” J. Am. Ceram. Soc., 47, No. 12, 632–635 (1964).CrossRefGoogle Scholar
  9. 9.
    K.L. Lin, and C.C. Lin, “Ti2ZrO phases formed in the titanium and zirconia interface after reaction at 1550°C,” J. Am. Ceram. Soc., 88, No. 5, 1268-1272 (2005).CrossRefGoogle Scholar
  10. 10.
    K.L. Lin, and C.C. Lin, “Zirconia-related phases in the zirconia/titanium diffusion couple after annealing at 1100–1550°C”, J. Am. Ceram. Soc., 88, No. 10, 2928–2934 (2005).Google Scholar
  11. 11.
    K.L. Lin, and C.C. Lin, “Effected of annealing temperature on microstructural development at the interface between zirconia and titanium,” J. Am. Ceram. Soc., 90, No. 3, 893–899 (2007).CrossRefGoogle Scholar
  12. 12.
    K.L. Lin, and C.C. Lin, “Transmission electron microscope investigation of the interface between titanium and zirconia,” J. Am. Ceram. Soc., 82, No. 11, 3179–3185 (1999).CrossRefGoogle Scholar
  13. 13.
    A.P. Tomsia, H. Ishibashi, E. Saiz, and J.S. Moya, “Powder processing of Mullite/Mo functionally graded materials,” J. Eur. Ceram. Soc., 18, No. 9, 1365–1371 (1998).CrossRefGoogle Scholar
  14. 14.
    J.F. Bartolome, M. Diaz, J. Requena, J.S. Moya, and A.P. Tomsia, “Mullite/Molybdenum ceramic-metal composites”, Acta Mater., 47, No. 14, 3891-3899 (1999).CrossRefGoogle Scholar
  15. 15.
    D. Doni Jayaseelan, D. Amutha Rani, T. Nishikawa, H. Awaji, and T. Ohjia, “Sintering and microstructure of mullite-Mo composites,” J. Eur. Ceram. Soc., 22, 1113–1117 (2002).CrossRefGoogle Scholar
  16. 16.
    J.F. Bartolome, M. Diaz, J.S. Moya, E. Saiz, and A.P. Tomsia, “Mullite/Mo interfaces formed by intrusion bonding”, J. Eur. Ceram. Soc., 24, 785–790 (2004).CrossRefGoogle Scholar
  17. 17.
    L.D. Teng, F.M. Wang, and W.C. Li, “Thermodynamics and microstructure of Ti–ZrO2 metal–ceramic functionally graded materials,” Mater. Sci. Eng. A, 293, Nos. 1–2, 130–136 (2000).CrossRefGoogle Scholar
  18. 18.
    T. Lidonga, and L. Wenchaob, “Residual stress analysis of Ti–ZrO2 thermal barrier graded materials,” Mater. Design, 23, 627–632 (2002).CrossRefGoogle Scholar
  19. 19.
    P. Lada, P. Falkowski, A. Miazga, K. Konopka and M. Szafran, “Fabrication of ZrO2–Ti composites by slip casting method,” Arch. Metall. Mater., 61, No. 2B, 1095–1100 (2016).CrossRefGoogle Scholar
  20. 20.
    M. Chmielewski, S. Nosewicz, D. Jakubowska, M. Lewandowska, and P. Bazarnik, “The influence of sintering time on the microstructural properties of chromium-rhenium matrix composites,” Int. J.Refractory Metals and Hard Materials, 59, 78–86 (2016).CrossRefGoogle Scholar
  21. 21.
    J.A. Munoz-Tabares, J. Reyes-Gasga, E. Jiménez-Piqué, and M. Anglada, “Microstructural changes in ground 3Y-TZP and their effect on mechanical properties,” Acta Mater., 59 No. 17, 6670–6683 (2011).CrossRefGoogle Scholar
  22. 22.
    P. Lada, A. Miazga, P. Bazarnik and K. Konopka, “Microstructure Characterization of Composite from ZrO2–Ti System,” Arch. Metall. Mater., 62, No. 4, 2045–2049 (2017).CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2018

Authors and Affiliations

  • P. Lada
    • 1
  • A. Miazga
    • 1
  • P. Bazarnik
    • 1
  • K. Konopka
    • 1
  • M. Szafran
    • 2
  1. 1.Warsaw University of Technology, Faculty of Materials Science and EngineeringWarsawPoland
  2. 2.Faculty of ChemistryWarsaw University of TechnologyWarsawPoland

Personalised recommendations